Autel MaxiService EBS301 Manual
  1. Manuals
  2. Brands
  3. Autel Manuals
  4. Test Equipment
  5. MaxiService EBS301
  6. Manual

Autel MaxiService EBS301 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
1.
SAFETY PRECAUTIONS AND WARNINGS .............................................. 1
2.
GENERAL INFORMATION .......................................................................... 2
2.1
2.2
2.3
2.4
2.5
2.6
3.
USING THE SCAN TOOL .............................................................................. 8
3.1
3.2
3.3
3.4
3.5
3.6
3.7
V
3.8
4.
PLAYBACK DATA ....................................................................................... 17
4.1
4.2
4.3
5.
OBDII DIAGNOSTICS ................................................................................. 19
5.1
5.2
5.3
5.4
5.5
5.6

Table of Contents

.................................................................................... 6
...................................................................................... 8
.......................................................................................... 10
.................................................................................................. 10
........................................................................................................ 10
............................................................................................ 11
.................................................................................. 15
....................................................................................... 17
......................................................................................... 18
.......................................................................................... 18
............................................................................................... 20
.............................................................................................. 23
.................................................................................................. 25
........................................................................................... 31
..................................................................................... 35
(OBD) II ............................................................. 2
) ........................................................ 2
.................................................................... 4
......................................................... 5
............................................................................. 10
.................................................................... 16
......................................................... 32
(DLC) .................................... 3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MaxiService EBS301 and is the answer not in the manual?

Questions and answers

Related Manuals for Autel MaxiService EBS301

Summary of Contents for Autel MaxiService EBS301

  • Page 1: Table Of Contents

    Table of Contents SAFETY PRECAUTIONS AND WARNINGS ..........1 GENERAL INFORMATION ................2 (OBD) II ............. 2 OARD IAGNOSTICS (DTC ) ............2 IAGNOSTIC ROUBLE ODES (DLC) ........3 OCATION OF THE ONNECTOR OBD II R ..............4 EADINESS ONITORS OBD II M ............
  • Page 2 ................ 36 OARD ONITOR ..................39 OMPONENT .............. 40 IEWING EHICLE NFORMATION 5.10 M ..................42 ODULES RESENT 5.11 DTC L ..................... 43 OOKUP PRINT AND UPDATE................... 45 6.1....................45 RINT 6.2..................46 OFTWARE UPDATE EPB ........................52 7.1.

  • Page 3: Safety Precautions And Warnings

    1. Safety Precautions and Warnings To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle:  Always perform automotive testing in a safe environment. ...

  • Page 4: General Information

    2. General Information 2.1 On-Board Diagnostics (OBD) II The first generation of On-Board Diagnostics (called OBD I) was developed by the California Air Resources Board (ARB) and implemented in 1988 to monitor some of the emission control components on vehicles. As technology evolved and the desire to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed.

  • Page 5: Location Of The Data Link Connector (Dlc)

    2.3 Location of the Data Link Connector (DLC) The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic scan tools interface with the vehicle's on-board computer. The DLC is usually located 12 inches from the center of the instrument panel (dash), under or around the driver’s side for most vehicles.

  • Page 6: Obd Ii Readiness Monitors

    2.4 OBD II Readiness Monitors An important part of a vehicle’s OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components have been evaluated by the OBD II system. They are running periodic tests on specific systems and components to ensure that they are performing within allowable limits.

  • Page 7: Obd Ii Monitor Readiness Status

    monitors are termed non-continuous monitors. For different ignition type engines, the available monitors are different too. The following monitors are to be used for spark ignition engines only: EGR System O2 Sensors Catalyst Evaporative System O2 Sensor Heater Secondary Air Heated Catalyst The following monitors are to be used for compression ignition engines only:...

  • Page 8: Obd Ii Definitions

    including erasing of diagnostic trouble codes (DTCs) with a scan tool or a disconnected battery, can result in Readiness Monitors being set to “Not Ready”. Since the three continuous monitors are constantly evaluating, they will be reported as “Ready” all of the time. If testing of a particular supported non-continuous monitor has not been completed, the monitor status will be reported as “Not Complete”...
  • Page 9 of the enabling criteria. Drive cycles vary among vehicles and for each monitor in any particular vehicle. OBD II Drive Cycle -- A specific mode of vehicle operation that provides conditions required to set all the readiness monitors applicable to the vehicle to the “ready” condition. The purpose of completing an OBD II drive cycle is to force the vehicle to run its onboard diagnostics.

  • Page 10: Using The Scan Tool

    3. Using the Scan Tool 3.1 Tool Description CONNECTOR -- Connects the scan tool to the vehicle’s Data Link Connector (DLC). LCD DISPLAY -- Indicates test results. TFT color display (320 x 240 dpi). FUNCTION BUTTON – Corresponds with “buttons” on screen for executing commands.
  • Page 11 ESC BUTTON -- Cancels a selection (or action) from a menu or returns to the previous screen. LEFT SCROLL BUTTON -- When look up DTC definitions, moves to previous character and views additional information on previous screens if DTC definition covers more than one screen;...

  • Page 12: Specifications

    3.2 Specifications Display: TFT color display (320 x 240 dpi) Operating Temperature: 0 to 60°C (32 to 140 °F) Storage Temperature: -20 to 70°C (-4 to 158 °F) External Power: 12.0 to 18.0 V power provided via vehicle battery or adapter. Dimensions: Length Width...

  • Page 13: System Setup

    Find DLC on vehicle.  A plastic DLC cover may be found for some vehicles and you need to remove it before plugging the OBD2 cable. Plug the cable to the vehicle’s DLC. Power up the scan tool , and wait for the Main Screen to appear.(Figure 3.1) Figure 3.1 3.6 System Setup...
  • Page 14 From the Main Screen: Use LEFT/RIGHT scroll button to select Setup, and press the OK button. Following the instructions to do adjustments and settings could make your diagnosis more conveniently and easily. (Figure 3.2) Figure 3.2 Language Setup  English is the default language. From System Setup screen, use the UP/DOWN scroll button and LEFT/RIGHT scroll button to select Language, and press the OK button.
  • Page 15 Unit of Measure  Metric is the default measurement unit. From System Setup screen, use the LEFT/RIGHT scroll button to select EN/METRIC and press the OK button. From Unit of Measure screen, use the LEFT/RIGHT scroll button to select the desired unit of measurement. (Figure 3.4 ) Figure 3.4 Press the OK button to save your selection and return to previous menu.
  • Page 16 Figure 3.5 Key Test The Key Test function checks if the keyboard is working properly. From System Setup screen, use the UP/DOWN scroll button and LEFT/RIGHT scroll button to select Key Test, and press the OK button. Press any key to start test. When you press a key, the edge around corresponding key on the screen should turn to red.

  • Page 17: Vehicle Coverage

    About The About function allows viewing of some important information such as serial number and software version number of the scanner. From System Setup screen, use the UP/DOWN scroll button and LEFT/RIGHT scroll button to select About and press the OK button;...

  • Page 18: Product Troubleshooting

    For your vehicle to be OBD II compliant it must have a 16-pin DLC (Data Link Connector) under the dash and the Vehicle Emission Control Information Label must state that the vehicle is OBD II compliant. 3.8 Product Troubleshooting Vehicle Linking Error A communication error occurs if the scan tool fails to communicate with the vehicle’s ECU (Electronic Control Unit).

  • Page 19: Playback Data

    4. Playback Data The Playback Data function allows viewing data from last test recorded by the scan tool. 4.1 Reviewing Data Use the UP/DOWN scroll button and LEFT/RIGHT scroll button to select Playback from Main Screen (Figure 3.1), and press the OK button. Wait for the Review data screen to appear. Review data 1.EPB 2.Scan...

  • Page 20: Deleting Data

     If no data from previously tested vehicle is recorded, a message “No data available!” shows on the screen. Review selected data on screen. Vehicle Specification Vehicle: Mustang Engine Type: Other Capacity: 3.8L Transmission: Manual Fuel Type: Gasoline Emission Level: Federal Emission VIN:1FAFP40462F100819 PrefSuf:2R3APB VersionID:4612...

  • Page 21: Obdii Diagnostics

    5. OBDII Diagnostics The OBD II Diagnostics function is a fast-access option that allows you to carry out a quick test on the engine system of OBD II vehicles. When more than one vehicle control module is detected by the scan tool, you will be prompted to select the module where the data may be retrieved.

  • Page 22: Read Codes

    vehicle. Contact your local distributor manufacturer’s customer service department for assistance. 7） View a summary of system status (MIL status, DTC counts, Monitor status) on screen. (Figure 5.1 ) Press ESC button for Diagnostic Menu (Figure 5.3) to come up. System Status MIL Status Codes Found...
  • Page 23 more than a specified amount of key-cycles. These codes will cause the control module to illuminate the malfunction indicator light (MIL) when emission-related fault occurs.  Pending Codes are also referred to as “maturing codes” or “continuous monitor codes”. They indicate problems that the control module has detected during the current or last driving cycle but are not considered serious yet.
  • Page 24 Read Codes 1.Stored Codes 2.Pending Codes 3.Permanent Codes Figure 5.4  If there is not any Diagnostic Trouble Code, the display indicates “No (pending) codes are stored in the module!” Wait a few seconds or press any key to return to previous screen. NOTE: Permanent Codes function is available for merely vehicles supporting the CAN protocols.

  • Page 25: Erase Codes

     If the manufacturer of your vehicle is not listed, use the UP/DOWN scroll button to select Other and press the OK button. 5.2 Erase Codes CAUTION: Erasing the Diagnostic Trouble Codes may allow the scan tool to delete not only the codes from the vehicle’s on-board computer, but also “Freeze Frame”...
  • Page 26  If you press Yes function key or OK button, a warning message will come up asking your confirmation. (Figure 5.7) Erase Codes DTCs and Freeze Data will be lost Do you wish to continue? Figure 5.7 3) Press the OK button to confirm. ...

  • Page 27: Live Data

    Press any button to return to Diagnostic Menu. 5.3 Live Data In this function, you can not only read the live data but also record data for later review. Viewing Data The View Data function allows viewing of live or real time PID data of vehicle’s computer module(s).
  • Page 28 …………………Live Data 1. Complete List 2. Custom List Figure 5.11 2) View live PIDs on the screen. Use the UP/DOWN scroll button for more PIDs if additional information is available on more than one page.( Figure 5.12) Complete List Numbers of DTCs Fuel system 1 status Fuel system 2 status Calculated load value...
  • Page 29 Figure 5.13  If the “Merge Graph” on the bottom appears when a PID is selected to view, merged graph information is available. (Figure 5.14) NOTE: Merge Graph can be used to compare two related parameters in graphic mode, which is especially convenient in the Custom List option where you could select two interacted parameter to merge and see their relationship.
  • Page 30  Select Pause to suspend viewing. You could resume the viewing process again by selecting Start. 3) Press the ESC button to return to previous menu. B. Viewing Custom List 1) To view customized PID data, use the UP/DOWN scroll button to select Custom List from Live Data menu and press the OK button.( Figure 5.11) 2) Use the UP/DOWN scroll button to move up and down to the...
  • Page 31 Custom List Numbers of DTCs Fuel system 1 status Pause Graphics Save Figure 5.16 Use the ESC button to return to previous menu. Recording Data The Record Data function allows recording vehicle modules’ Parameter Identification (PID) data help diagnose intermittent vehicle problems. You could save data files to the SD card and then use the Playback function to view the saved files.
  • Page 32  If you record live data under graph mode, following screen shows: Figure 5.18 NOTE: The scan tool can only playback text data even though the data is saved in graphic mode. When there is not enough memory space, a warning message prompting to delete previously recorded data.

  • Page 33: Freeze Frame

    Select Pause to suspend recording. You could resume the recording process again by selecting Start. You may review the saved data in Playback function. Press ESC button to exit. 5.4 Freeze Frame Freeze Frame Data allows the technician to view the vehicle’s operating parameters at the moment a DTC (Diagnostic Trouble Code) is detected.

  • Page 34: Retrieving I/M Readiness Status

    Select Save to record freeze frame. A confirming message “Save success!” shows on the display and scan tool return to previous menu. If you don’t want to save the freeze frame data, press ESC button to return to previous screen. 5.5 Retrieving I/M Readiness Status I/M Readiness function is used to check the operations of the Emission System on OBD2 compliant vehicles.
  • Page 35 1) Use the UP/DOWN scroll button to select I/M Readiness from Diagnostic Menu and press OK button. (Figure 5.3) 2) Wait a few seconds while the scan tool validates the PID MAP. If the vehicle supports both types of tests, then both types will be shown on the screen for selection.
  • Page 36  FUEL -- Fuel System Monitor  CCM -- Comprehensive Component Monitor  EGR – EGR System Monitor  HCCAT -- NMHC Catalyst Monitor  NCAT -- NOx Aftertreatment Monitor  BP -- Boost Pressure System Monitor  EGS -- Exhaust Gas Sensor Monitor ...

  • Page 37: O2 Monitor Test

    7) Press the ESC button to return to Diagnostic Menu. 5.6 O2 Monitor Test OBD2 regulations set by SAE require that relevant vehicles monitor and tests on the oxygen (O2) sensors to identify problems related to fuel efficiency and vehicle emissions. These tests are not on-demand tests and they are done automatically when engine operating conditions are within specified limits.

  • Page 38: On-Board Monitor Test

    …………….O2 Monitor Test………….. The selected mode is not supported! Press any key to continue Figure 5.25 View test results of selected O2 sensor. (Figure 5.26) … ……… .O2 Bank1 Sensor2 Rich-Lean Threshd V Lean-Rich Threshd V Low for Switch (V) High for Switch (V) Rich-Lean Threshd S Lean-Rich Threshd S...
  • Page 39 and a current value for each monitor. By comparing the current value with the minimum and maximum value, the scan tool will determine if it is OK. Use the UP/DOWN scroll button to select On-Board Monitor Test from Diagnostic Menu and press the OK button. (Figure 5.3) Wait a few seconds while the scan tool validates the PID MAP.
  • Page 40  If the vehicle under test does not support the mode, an advisory message will be displayed on the screen. (Figure 5.29) On-Board Monitor Test The selected mode is not supported Press any key to continue Figure 5.29  For CAN-equipped vehicles, test selections can be as below: On-Board Monitor Test 1.

  • Page 41: Component Test

     For CAN-equipped vehicles, test results displayed can be as below: Flow Test Module Test Value 0.10 Min Limit 0.00 Max Limit 95.0 Status Figure 5.32 Press ESC button to return to the previous menus. 5.8 Component Test The Component Test function allows initiating a leak test for the vehicle's EVAP system.

  • Page 42: Viewing Vehicle Information

    3) If the test has been initiated by the vehicle, a confirmation message will be displayed on the screen. Component Test Command Sent! Press any key to continue Figure 5.34  Some vehicles do not allow scan tools to control vehicle systems or components.
  • Page 43 2) An advisory message comes up to remind you. Wait a few seconds or press any key to continue. Vehicle Info. Turn key on with engine off ! Press any key to continue Figure 5.36 3) Wait for the scan tool to display the Vehicle Info. menu. Vehicle Info.

  • Page 44: Modules Present

    Vehicle ID Number 1FAFP40462F100819 Figure 5.38 6) Press the ESC button to return previous menu 5.10 Modules Present The Modules Present function allows viewing of the module IDs and communication protocols for OBD2 modules in the vehicle. 1) Use the UP/DOWN scroll button to select Modules Present from Diagnostic Menu and press OK button.

  • Page 45: Dtc Lookup

    5.11 DTC Lookup The DTC Lookup function allows user to search definitions of DTC stored in built-in DTC library. Use the UP/DOWN scroll button to select DTC Lookup from Diagnostic Menu and press OK button. (Figure 5.3) Wait for the scan tool to display the DTC Lookup screen. DTC Lookup Only PCBU can be the first letter to be put in.
  • Page 46 Trouble Codes P0005 Fuel Shutoff Valve A Control Circuit/Open Save Figure 5.42  Use the LEFT/RIGHT scroll button to view the previous / next DTC.  Select Save to record code definition.  For manufacturer specific codes, you need to select a vehicle make on an additional screen to look for DTC definitions.

  • Page 47: Print And Update

    A PC or laptop with USB ports A USB cable Install PC Suit through the included CD, or download the applications in our website: www.autel.com or our distributors’ site. Connect the scanner to computer with the USB cable supplied. Run Printer software on computer.

  • Page 48: Software Update

     Register the Tool User would update the scan tool ONLY after you had registered the tool on our website: www.autel.com. Then you could download software, update online, retrieve information and get warranty service. NOTE: Prior to registration, please confirm your network is working properly.
  • Page 49 If you are a new member to Autel and do not have an account yet, click the Create Autel ID button on the left side. Enter the required information in the input fields, read through Autel’s Terms and Conditions and tick on Agree, and then click...
  • Page 50 Figure 6.2 Enter your Autel ID and password and wait for the Update window to display. If you forget your password unintentionally, you may always click the [Forget Password?] to link to our website and find your password back. Select the product type and serial number, click OK to continue.
  • Page 51 Selected Items button on the right side of screen.  Or, click on the Select All checkbox on the right side of screen and all updatable items will be selected automatically. Then click the Update Selected Items button on the right side of screen.
  • Page 52 old version. Insert the Micro SD card into the scan tool, and restart the scan tool to finish the whole update.  View or Delete Programs To view the list of installed programs or to delete an installed program, please follow these steps: ...
  • Page 53 Theoretically, all programs in latest versions will be automatically compatible with the older versions, but if your scan tool do have a compatible problem and want to retrieve the older version for some programs, you may need to delete them first then install the older version again.

  • Page 54: Epb

    Ensure that the EPB control system is reactivated after the maintenance work has been completed. You may have to activate several times to position the brake pads. NOTE: Autel accepts no responsibility for any accident or injury arising from the maintenance of the Electrical Parking Brake system.
  • Page 55 Connect the tool to vehicle and power on. Turn the ignition on. Select EPB icon in the Main Screen (Figure 3.1) and wait for the vehicle manufacturer screen. Choose the correct vehicle make. (Take BENZ as an example) Figure 7.1 After you have selected the vehicle make (BENZ), the electrical parking brake system screen will display as below.
  • Page 56 In the Diag. Menu screen, use the UP/DOWN button to select Active Test, and press the OK button. Active Test 1.Installation position of brake cables 2.Operate parking brake Figure 7.3 A. Installation position of brake cables This function allows you to adjust the brake cables safely. After you select this function, the tool will prompt you a safety message.
  • Page 57 Installation position of brake cable The actuation can be activated using the following function key Operating statuses Released Electronic parking brake Figure 7.5 Operate parking brake This function allows you to deactivate or reactivate the electronic brake systems. After you select this function, the tool will prompt you a safety message.
  • Page 58 By selecting Operate/Release function key, you can do the electronic parking brake system service safely and easily. Operate parking brake Operating statuses Operate Electronic parking brake Mode Electronic parking Vehicle brake stationary Operating statuses Released Electronic parking brake Release Operate Figure 7.8 ...

  • Page 59: Warranty And Service

    8. Warranty and Service 8.1. Limited One Year Warranty Autel warrants to its customers that this product will be free from all defects in materials and workmanship for a period of one (1) year from the date of the original purchase, subject to the following terms and...

Table of Contents