Alinco DJ-X2000T Instruction Manual
  1. Manuals
  2. Brands
  3. Alinco Manuals
  4. Receiver
  5. DJ-X2000T
  6. Instruction manual

Alinco DJ-X2000T Instruction Manual

Wide range scanning receiver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Scanning Receiver Certification Report
C
N
:
A
OMPANY
AME
LINCO
EUT:
DJ-X2000T
W
O
N
:
2000448
ORK
RDER
UMBER
FCC ID:
EUG DJ-X2000T
APPENDIX G:
INSTRUCTION MANUAL
, I
.
NC
Page 57 of 65

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DJ-X2000T and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Alinco DJ-X2000T

Summary of Contents for Alinco DJ-X2000T

  • Page 1 OMPANY LINCO EUT: DJ-X2000T 2000448 RDER UMBER FCC ID: EUG DJ-X2000T APPENDIX G: INSTRUCTION MANUAL Scanning Receiver Certification Report Page 57 of 65...
  • Page 2 WIDE RANGE SCANNING RECEIVER DJ-X2000 Instruction Manual Thank you for purchasing the ALINCO receiver. The DJ-X2000 instruction C L R manual contains important safety and operating instructions. Read this manual carefully before using the product.
  • Page 3 Features The Alinco DJ-X2000 is a professional multifunctional receiver which covers a wide band of radio media from the low-frequency band (LF) to ultrahigh- frequency (UHF) band. It has the following features. 1. Wide frequency range The DJ-X2000 covers the wide frequency range from 0.1 to 2149.999950 MHz.
  • Page 4 11. Frequency editing You can copy the content of one memory channel to another, or rename memory channels. 12. Transweeper The DJ-X2000 detects the listening microphone which transmits a radio wave. If a listening microphone is found, the DJ-X2000 will alert you with a display and warning sound.
  • Page 5 Contens 1. Before use ……………………………………………………00 1.1 Unpacking the receiver ………………………………………………00 1.2 Precautions in use ……………………………………………………00 1.3 Names of parts and their funciotns …………………………………00 1.3.1 Top, front and left side panels …………………………………………………………00 1.3.2 Rear and right panels ……………………………………………………………………00 1.3.3 Display ……………………………………………………………………………………00 1.3.4 Key pad ……………………………………………………………………………………00 1.4 Setting up the DJ-X2000 ………………………………………………00 1.4.1 Attaching the antenna……………………………………………………………………00...
  • Page 6 2.13.2 Setting the ON timer …………………………………………………………………00 2.14 Basic modes …………………………………………………………00 2.14.1 VFO mode ………………………………………………………………………………00 2.14.2 PMS mode ………………………………………………………………………………00 2.14.3 MR mode ………………………………………………………………………………00 2.15 Using HELP menu …………………………………………………00 3. Other Useful Functions ……………………………………00 3.1 Functions common to all modes ……………………………………00 3.1.1 Selecting a signal mode …………………………………………………………………00 3.1.2 Setting the frequency step ………………………………………………………………00 3.1.3 Attenuating interference from other cannels(ATT) ……………………………………00 3.1.4 Battery Save ………………………………………………………………………………00...
  • Page 7 3.1.30 Transceiver function ……………………………………………………………………00 3.1.31 Directly changing the settings…………………………………………………………00 Functions in the VFO mode ………………………………………00 3.2.1 VFO link function …………………………………………………………………………00 3.2.2 Scanning between VFO's A and B(AB SCAN) ………………………………………00 3.2.3 Copying frequencies from memories to the VFO ……………………………………00 3.2.4 Copying frequencies from the PMS mode to the VFO ………………………………00 3.3 PMS mode functions …………………………………………………00 3.3.1 Programmed scan operations …………………………………………………………00 3.3.2 Setting scan pass-frequency……………………………………………………………00...

  • Page 8: How To Read This Manual

    How to read this manual The following typographical and graphic conventions are used in this instruction manual. Bold typeface indicates titles of chapters and sections as well as messages shown on the display. When used to indicate displayed messages, only the part of the message that is pertinent to the explanation is given.
  • Page 9 FOR HOME OR OFFICE USE Information in this document are subject to change without notice or obligation.All brand names and trademarks are the property of their respective owners. Alinco cannot be liable for pictorial or typographical inaccuracies. Some parts, options and/or accessories are unavailable in certain areas.

  • Page 10: Before Use

    • Do not disassemble or tamper with the receiver. The DJ-X2000 is not warranted for troubles or accidents resulting from unauthorized modifications, regardless of the warranty period. Alinco dealer also reserves the right to refuse to service the receiver in such event.

  • Page 11: Names Of Parts And Their Functions

    1.3 Names of parts and their functions This section describes parts by name and function. 1.3.1 Top, front and left side panels C L R 1. Dial Use to switch frequency and memory channel, to adjust the audio volume and squelch level, and to make other settings.
  • Page 12 (Function) key Use this key in combination with other keys to call up specific functions. MONI Temporarily cancels the squelch for the duration it is held down. Used independent of squelch level. SRCH Press to start scanning with in a 40-channel range. Use in combination with key to start scanning in a 7-channel range.

  • Page 13: Rear And Right Panels

    1.3.2 Rear and right panels 1. DC-IN Connect an external DC supply here (10 - 16 V). 2. Holes for attaching belt clip Screw the included belt clip to the DJ-X2000 here. 3. Battery case lock Slide to the right to detach the battery case. 4.
  • Page 14 1.3.3 Display 2.3.4. 5. 6. 7. 8. 10. 12. 11. 13. Meter for displaying sound level. Displayed when the key has been pressed to indicate that you can access the subfunctions of the keys. 3. PRIO Displayed while the priority function is ON. 4.
  • Page 15 1.3.4 Key pad MODE Inputs 1. Press in combination with the key to switch the radio band. STEP Inputs 2. Press in combination with the key to set frequency step. Inputs 3. Press in combination with the key to turn the attenuator ON/OFF.

  • Page 16: Setting Up The Dj-X2000

    1.4 Setting up the DJ-X2000 Before using your receiver, attach the included antenna securely. If wanting to use the belt clip or wrist strap, attach them too. 1.4.1 Attaching the antenna Fit the base of the antenna over the projections on the connector, press downward and turn clockwise.

  • Page 17: About The Batteries

    1.5 About the batteries 1.5.1 Attaching the battery pack • To detach the battery pack Slide the battery pack lock on the case to the right and pull the case downward to detach. • To attach the battery pack Fit the battery pack into the holes on the DJ-X2000 and push in the direction of the arrow until the case snaps into the place.

  • Page 18: About The Battery Pack

    1.5.2 About the battery pack Before using the included EBP-37N battery pack, please note the followings. 1. The battery pack is not charged before it is shipped from the factory. Charge the pack before using the DJ-X2000 for the first time. 2.

  • Page 19: Ni-Cd Battery Pack

    1.5.3 Ni-Cd battery pack The supplied battery charger is designed exclusively for use with our NiCd battery pack. Precautions in using the charger 1. The battery charger is designed exclusively for use with our NiCd battery pack. Never use it to recharge any other rechargeable battery or dry cell. 2.
  • Page 20 • Recharging procedure Plug the AC power cord into the AC power socket on the battery charger. Insert the battery pack being recharged, along CL R the guides provided on both sides of the battery charger. The lamp will be illuminated in red, and quick recharge will be started.

  • Page 21: Battery Low Alarm

    Precautions in recharging 1. Ensure that the transceiver is OFF when recharging the battery pack. The use of the transceiver during the recharging can cause the transceiver to malfunction. 2. The battery charger is designed to be used at an ambient temperature between 10°C and 40°C.

  • Page 22: Basic Operations

    To turn ON/OFF the DJ-X2000, perform the following operation: • Turning ON Hold down the POWER switch for approx. 1 second until the message “ALINCO INTELLIGENT RECEIVER” appears on the display. • Turning OFF Hold down the POWER switch until the display goes out.

  • Page 23: Squelch Control

    2.3 Squelch control Squelch is used to mute the speaker noise when no signal is being received. Squelch level can be selected between SQ0 and SQ9. Setting is made as follows. A squelch level can be selected from the range between S00 and S32. To select a squelch level, press the SQL key located on the left side of the body, and then press the UP/DOWN...
  • Page 24 Note: If you enter any frequency that cannot be divided by the set frequency step, “S” appears on the display. • Setting with the UP/DOWN key For higher frequencies, press the UP key. For lower frequencies, press the DOWN key. The frequency will increase/decrease in the set frequency steps.

  • Page 25: Switching Frequency Band

    2.5 Switching frequency band The DJ-X2000 uses a dual VFO system, so that a frequency change can be done smoothly by inputting a new frequency on the second band in advance. The frequency currently being monitored is displayed next to the capital letter on the top line of the display.

  • Page 26: Searching (Channel Scope)

    If live frequencies are received, scanning is temporarily stopped. To resume scanning, turn the dial or press the UP/DOWN key. Scanning can be automatically resumed by specifying scan resuming conditions. For further details, see “3.1.15 Specifying scan resuming conditions” (page 43). •...

  • Page 27: Monitoring (Squelch Off)

    • To tune in live frequencies To move live frequencies to the left, turn the dial clockwise or press the 8 1 . 5 UP key. To move them to the right, 1 4 5 . 3 4 turn the dial counterclockwise or press the DOWN key.

  • Page 28: Turning Backlight On/Off Manually

    2.10 Turning backlight ON/OFF The DJ-X2000 has a backlight to make it easier to use at night. The backlight can be turned ON/OFF as follows. 2.10.1 Turning backlight ON/OFF manually • To turn the backlight ON LAMP Press the key. The display will be lit while operating the dial or keys.

  • Page 29: Turning Beep On/Off

    Select a backlight mode as follows: Using the dial or UP/DOWN key, point the arrow at a desired mode, and then press the key (the initial setting is the MOMENTARY mode). AUTO: The backlight is lit for 5 seconds after the dial or key is used.

  • Page 30: Setting The Clock

    2.12 Locking/Unlocking This feature locks all but certain keys, preventing accidental operation of the keys. Keys can be locked/unlocked as follows. • To lock keys Press the key, and then press key with 8 1 . 5 appearing on the display. 1 4 5 .

  • Page 31: Setting The On Timer

    Call up the OFF timer screen. Point the arrow at +OFF Timer using the dial or UP/DOWN T i me r key, and then press the key. O F F Set the OFF timer. Point the arrow at ON using the UP/DOWN key, and then set the time that will be taken until the power is automatically turned OFF (the initial setting is OFF).

  • Page 32: Basic Modes

    After finishing the setting, press the key. The display will return to the HELP TIMER menu. Point the arrow at END and then press the key. HELP (Alternatively, you may press the key, and then press the key with HELP appearing on the display.) SKIP Note:...

  • Page 33: Pms Mode

    2.15.2 PMS mode The PMS mode has a total of 20 programmable bands, 10 each for the capital P and lower case p. Enter the PMS mode. Press the key. This will engage the PMS mode. Then, select a 1 4 . 7 5 registered band and start scanning.

  • Page 34: Using Help Menu

    Select a channel. Using the dial or UP/DOWN key, select a channel between 00 and 39. The assigned frequency will appear on the upper line of the display and its name on the lower line. 2.15 Using HELP menu The HELP menu is used to display the information on whatever function or operation you want to know.

  • Page 35: Other Useful Functions

    3. Other Useful Functions This chapter describes the useful functions of the DJ-X2000. 3.1 Functions common to all modes This section describes the functions that are commonly available in the VFO, PMS, and MR modes. 3.1.1 Selecting a signal mode Press the key, and then press MODE...

  • Page 36: Attenuating Interference From Other Channels (Att)

    Note: In the PMS or MR mode, setting DIRECT WR to ON enables selection of a frequency step and radio type and adjustment of the attenuator and CTCSS decoders. For further details, see “3.3.31 Directly changing the setting” (page 63). If AUTO STEP is selected, the most suitable frequency step for the received frequency band will be automatically selected.

  • Page 37: Battery Save

    Note: • The attenuation level slightly varies depending on the frequency. • In the PMS or MR mode, setting DIRECT WR to ON enables selection of a frequency step and radio type and adjustment of the attenuator and CTCSS decoders. For further details, see “3.3.31 Directly changing the setting” (page 63).

  • Page 38: Copying Data Between Two Receivers (Clone)

    3.1.5 Copying data between two receivers (CLONE) You can copy settings stored in memory from one DJ-X2000 (master) to another (slave). This is referred to as "cloning". Cloning requires a cable with 2.5ø stereo plug to connect the two receivers. Turn ON two DJ-X2000 units and interconnect them.

  • Page 39: Selecting A Communication Speed

    When the cloning procedure is finished, the slave unit returns to the normal screen and the master unit to the CLONE menu. Finish the cloning procedure. Once the cloning procedure is finished, disconnect the cable from both DJ- SKIP X2000 units. Press the key on the master unit to exit the CLONE menu.

  • Page 40: Selecting A Language Mode

    Note: • The cloning procedure or communication with a personal computer is not possible between DJ-X2000 units with different communication speeds. • The initial value is a high speed of 38400 bps. If there are too many communication errors at this speed, retry the communication at a lower speed, e.g., 9600 bps.
  • Page 41 • Meter display mode Call up the CHECKER screen. M NAME Press the . The RF CHECK C H E C K menu will appear. Point the arrow C H E C K E R at CHECKER using the dial or C a l l  ...

  • Page 42: Displaying Battery Voltage

    3.1.9 Displaying battery voltage The battery voltage can be displayed as follows: Call up the BATT VOLT screen. Press the key, and then A T T   V O L T press the key with HELP 4 . 9 V shown on the display.

  • Page 43: Selecting The Bell Mode

    3.1.11 Selecting the BELL mode In this mode, when squelch is canceled, the buzzer sounds. Call up the BELL screen. Press the key, and then BEL L press the key with HELP OF F shown on the display. The BELL menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN key, and then press the key.

  • Page 44: Resetting The Receiver

    Select each character by turning the dial, and then establish it by pressing the DOWN key. Pressing the UP key allows you to cancel the established character. Up to 36 characters may be entered (the initial setting is ALINCO INTELLIGENT RECEIVER).

  • Page 45: Setting Scan Resume Condition (Scan Mode)

    3.1.14 Tuning in frequencies in the PMS/MR modes (M.TUNE) You can tune in frequencies in the PMS and MR modes. You do not have to return to the VFO mode. • To tune in a frequency While in the PMS or MR mode, press the key.

  • Page 46: Setting Scan Signal Level

    Select a scanning option. Point the arrow at the desired option using the dial or UP/DOWN key, and then press the key. The available scanning options are described below (the initial setting is BUSY): BUSY Busy scan. The DJ-X2000 stays on any signal it locates until the signal vanishes.

  • Page 47: Setting The Scanning Pause Period

    Select an S-meter level. Point the arrow at ON using the UP/DOWN key. Select a level from 1 through 7 using the dial, and then press the key. If you do not want to select any S- meter level, select OFF and then press the key (the initial setting is OFF).

  • Page 48: Selecting A Priority Option

    3.1.18 Turning the priority function ON/OFF The priority function checks another channel (priority channel) every 5 seconds while monitoring the current frequency. For the settings of the priority feature, see “3.1.19 Selecting a priority option” (page 46), “3.1.20 Selecting a priority channel”...

  • Page 49: Setting Priority Signal Channel

    Call up the PRI MODE screen. PR I MODE Point the arrow at +PRI MODE using the dial or S T O P UP/DOWN key, and then press the key. T I MER Select a priority option. Select a priority option using the dial or UP/DOWN key, and then press key.

  • Page 50: Specifying A Priority Interval

    Call up the PRI MEMORY screen. Point the arrow at +MEMORY using the dial or UP/DOWN key, and then press the key. R I MEMORY Select a channel. Select the desired memory bank and channel, and then press the key. F TUNE The memory bank can be selected from A through E using the key.

  • Page 51: Setting Search Resume Condition (Srch Mode)

    Specify a priority interval. Specify a priority interval in a range between 1 and 12 seconds in 1-second steps using the UP/DOWN key, and then press the key (the initial setting is 5s). The display will return to the PRIO menu. Point the arrow at END and then press key (Alternatively, you may press the key, and then press the key with...

  • Page 52: Flash Tune

    Select a search resuming option. Point the arrow at the desired option using the dial or UP/DOWN key, and then press the key. The available options are described below (the initial setting is INTERVAL): SRCH SINGLE The search is carried out only once when the key is pressed.
  • Page 53 Select the Flash tune. Point the arrow at the desired option using the dial or UP/DOWN key, and then press the key (the initial setting is F TUNE). F TUNE Instantaneously checks for a radio frequency and automatically tunes in to the detected frequency. F COUNTER Check for a radio frequency and shows the detected frequency in real time (the frequency resolution is...
  • Page 54 3.1.24 Descrambler This function descrambles the scrambled voice signals. Note: Only the NFM type radio signals can be descrambled. Call up the SET SCRAMBLE screen and then turn ON the Descrambler. Press the key, and then press SCRT key with shown on ヒ...

  • Page 55: Ctcss Decoding Function

    3.1.25 CTCSS decoding function This function is used to receive CTCSS signals. It allows you to receive 38 waves of CTCSS signals and even select the reverse reception. The function is also applicable to taxi radio. Note: Only the NFM type radio can be received as CTCSS signals. •...
  • Page 56 • CTCSS scanning This function is used to scan for CTCSS signals. Call up the CTCSS SET menu. Press the key, and then press CTCSS key with shown on CTCSS SET MANUA L the display. C T CS S SCAN The CTCSS SET menu will appear.
  • Page 57 3.1.26 A/B squelch This function is used to start squelch by detecting free-line signals. Call up the A/B SQ SET screen. Press the key, and then press key with shown on A / B SQ SET HELP OF F the display. The menu will appear.
  • Page 58 3.1.27 Transweeper This function is used to detect a wireless microphone or any other bug using radio and locate the place where it is installed. If you previously assign any frequency expected for bugging purposes to the memory channel or auto memory channel, the DJ-X2000 will scan for that frequency.
  • Page 59 • As the DJ-X2000 goes away from the bug ＿ , , 1 5 4 . • The number of I shown at the lower right corner of the ＿ , , display tells you the distance to the location of the bug. Each I represents approximately 1 m.

  • Page 60: Recording Function

    3.1.28 Recording function This function is used to record the received sound or sound from the speaker using the internal IC. It allows you to record such sound for 160 seconds maximum. Recording, playback, and erasing can be repeated as many times as you like.
  • Page 61 Stop or pause the recording. STEP To stop the recording, press the key. F TUNE To pause (temporarily stop) the recording, press the key. If you press the F TUNE key again, the recording is resumed. When the recording time reaches 160 seconds, “END” appears on the display and the recording stops automatically.

  • Page 62: Sound Pickup

    • Erasing the recorded data Call up the recording screen. Press the key, and then press key with shown on R E C   S T O P   P L A Y the display. P U A S E The recording screen will appear.

  • Page 63: Transceiver Function

    3.1.30 Transceiver function This function allows you to use the DJ-X2000 as a transceiver. The <SRCH> key located on the left side of the DJ-X2000 will work as the PTT (Press to Talk) key. • Entering the TRANCEIVER mode Call up the TRANCEIVER screen. Press the key, and then press the...
  • Page 64 • Transmission and reception Select the frequency you want to receive. The frequency can be selected using the dial or UP/DOWN key. However, the following limitations apply: Radio type NFM only Frequency range 250.000 MHz to 259.975 MHz Frequency step Fixed at 25 kHz When is shown on the display by pressing the...

  • Page 65: Directly Changing The Settings

    3.1.31 Directly changing the settings This function allows you to enable/disable the direct changes of the settings for radio type, frequency step, attenuator, and CTCSS decoding function in the MR or PMS modes. When it is turned ON, the settings for radio type, frequency step, attenuator, and CTCSS decoding function can be directly changed in the currently displayed MR or PMS mode.

  • Page 66: Functions In The Vfo Mode

    3.2 Functions in the VFO mode This section describes various functions available in the VFO mode. 3.2.1 VFO link function This function is used to synchronously change two VFO frequencies, the currently received frequency and another frequency. Call up the LINK SET screen. Specify frequencies in bands A and B of VFO.

  • Page 67: Scanning Between Vfo's A And B (Ab Scan)

    3.2.2 Scanning between VFO's A and B (AB SCAN) This function is for scanning the band between the current frequencies of VFO-A and VFO-B. • To scan between VFO’s A and B Set frequency on each band A and B. 1 4 5 .

  • Page 68: Copying Frequencies From The Pms Mode To The Vfo

    3.2.4 Copying frequencies from the PMS mode to the VFO You can copy frequencies in the PMS mode to the VFO. Call up the frequency in memory. Press the key to get the PMS mode. Then set the program bank No. you want to display in the VFO mode.

  • Page 69: Pms Mode Functions

    3.3 PMS mode functions This section explains operations in the PMS mode. 3.3.1 Programmed scan operations This section is for programmed scan operations. Call up the PMS SET screen. Press the key, and then press e t PMS BANK key with shown on HELP - - - - .

  • Page 70: Setting Scan Pass-Frequency

    Select a frequency step. Point the arrow at the desired frequency step using the STEP 1 dial or UP/DOWN key, and then press the key. AU TO S T E P 5 H z Give a name to the program. Select each character by turning the dial and then establish it by pressing the DOWN key.

  • Page 71: Setting Program Link

    3.3.3 Setting program link This function lets you scan a combination of frequency ranges. Call up the PMS LINK screen. Press the key, and then press MS Ba n k L i n k key with shown on HELP P - - - - - - - - - - the display.

  • Page 72: Moving A Scanning Program

    Select a source program. Using the dial or a numeric key, select the program you F TUNE want to copy. Press the key (pressing the O P Y   F R O M 1 4 5 . 3 4 toggles between the uppercase P and lowercase p). Select a destination program.

  • Page 73: Deleting Scan Programs

    Select the desired destination program. Using the dial or a numeric key, select the destination F TUNE O V E   T O program number. Press the key (Pressing the P 2 - - - - . - - - - key toggles between the uppercase P and the lowercase - - - - - - - - SKIP...

  • Page 74: Mr Mode Functions

    3.4 MR mode functions This section explains operations into the MR mode. 3.4.1 Memorizing frequencies This function saves selected frequencies into memory channels. Set the frequency you want to memorize, in the VFO mode. Press the key to get the VFO mode. Then, set the frequency on the top line (currently used) band.

  • Page 75: Setting The Auto Memory Write Function

    3.4.2 Setting the auto memory write function This function is used to automatically assign the frequency that has been received during scanning in the PMS mode, to the memory bank. Call up the scanning program. Press the key to enter the PMS mode. Select a program bank number. The programmed scanning will start.

  • Page 76: Setting Memory Scan Radio System (Mode Sel)

    3.4.4 Setting memory scan radio system (MODE SEL) By setting a mode in the “MODE SEL” menu, the DJ-X2000 will selectively scan the memory channels of the specified mode. Call up the MODE SEL screen. Press the key, and then press key with shown on HELP...

  • Page 77: Using The Bank Link Function

    3.4.5 Using the BANK LINK function This function lets you scan specific memory banks. Call up the MR LINK screen. Press the key, and then press key with shown on HELP the display. MR L I NK MODE S E L The menu will appear.
  • Page 78 Select the program bank on which you want to set a memory channel for scanning. Using the dial or UP/DOWN key, point the arrow at the program you want to set. Press the key. B ANK B ANK 1 Select the program number you want to assign to a memory channel. Using the dial or UP/DOWN key, point the arrow at the program number you want to select.

  • Page 79: Scanning The Memory Channels Selected In The Pmr Screen

    3.4.7 Scanning the memory channels selected in the PMR screen This function is used to scan only the memory channel selected on the PMR screen (See “3.4.6 Selecting memory channels for scanning” (page 75)). • Scanning only the memory channels selected on the PMR screen. Press the key in the MR mode, and then press the A~B S...

  • Page 80: Copying Memory Channels

    Select a source memory bank. Using the dial or a numeric key, select the bank number F TUNE OPY BANK you want to copy. Press the key (Pressing the = - - key toggles from bank groups A through E). Select a destination memory bank.

  • Page 81: Moving A Memory Bank

    Select the bank that includes the memory channel to be copied. Select the bank number using the dial or a numeric key F TUNE (Pressing the key toggles from bank groups A O P Y F R O M A 2 - - - - . - - - - through E).

  • Page 82: Moving A Memory Channel

    Call up the MOVE BANK screen. Point the arrow at +MOVE BANK using the dial or UP/DOWN key, and then press the key. MR ED I T MO V E B ANK DE L B ANK Select the memory bank you want to move. Using the dial or a numeric key, select the memory bank OVE BANK you want to move.
  • Page 83 Call up the MOVE CH screen. Point the arrow at +MOVE CH using the dial or UP/DOWN key, and then press key. Select the bank that includes the memory channel you want to move. Select the bank number using the dial or a numeric key F TUNE (Pressing the key toggles from bank groups A...

  • Page 84: Deleting Memory Banks

    3.4.12 Deleting memory banks This function deletes entire memory banks. Call up the MR EDIT screen. Press the key, and then press MR ED I T key with shown on HELP COP Y CH the display. MOV E CH The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then press the key.

  • Page 85: Deleting And Restoring Memory Channels

    3.4.13 Deleting and restoring memory channels This function is used to delete and restore the frequency and name assigned to a memory channel. Call up the MR EDIT screen. Press the key, and then press key with shown on MR ED I T HELP COP Y CH the display.

  • Page 86: Searching For A Memory Tag

    3.4.14 Searching for a memory tag This function is used to search for a stored memory channel using its name. Call up the MR NAME SRC screen. Press the key, and then press M NAME N A M E   S R C key with appearing A BCDE FGH I J K...

  • Page 87: Specifications

    4. Appendix 4.1 Specifications Range of 0.1MHz〜2149.999950MHz received frequencies R e c e i v e d r a d i o t y p e WFM, NFM, AM, USB, LSB, CW AUTO STEP, 50Hz, 100Hz, 200Hz, 500Hz, 1kHz, 2kHz, 5kHz, 6.25kHz, 8.33kHz, 9kHz, 10kHz, 12.5kHz, 15kHz, 20kHz, 25kHz, Frequency steps 30kHz, 50kHz, 100kHz, 125kHz, 150kHz, 200kHz, 250kHz,...

  • Page 88: Troubleshooting

    4.2 Troubleshooting T r o u b l e C a u s e R e m e d i a l a c t i o n Press the VOL key on the left side of the The volume level is too DJ-X2000, and then turn up the volume (see low.

  • Page 89: List Of Help Menu Items

    4.4 List of Help menu items The list of Help menu items is given below. For the items marked with in the column for "Function involved", when the key is pressed, the currently displayed function or setting is executed. For the operation procedure for the Help menu, see "2.15 Help menu" (page 32). Organization of Help menu Describes how to use the Help information.
  • Page 90 Functions Operational M e n u S u b m e n u Function involved explanation available ● Inst ● COPY A=B ● COPY MR. CH ● COPY PMS ● ● Inst ● ● COPY CH ● ● DEL CH ●...
  • Page 91 Operational M e n u S u b m e n u Function involved explanation available ● AUTO ● MOMENTARY LAMP ● ALTERNATE ● Inst ● ● TIMER ● ● BEEP ● ● TONE ● ● STEREO ● ● BELL ●...
  • Page 92 Copyright 2000, Alinco,Inc. Osaka Japan Printed in Japan...

This manual is also suitable for:

Dj-x2000

Table of Contents