Table of Contents
Advertisement
Quick Links
SD-996C-NUVQ
Features:
• Vertical adjustable deadbolt opening, sliding
shim keeper, and deadlatch ramp
accommodates a wide range of lock types
• Accommodates deadbolts up to 1"
• Field selectable for fail-safe or fail-secure
• Reversible non-handed design fits either
right-hand or left-handed doors
• Includes 5 different stainless-steel faceplates
• Includes trim plate to hide gaps in installation
SD-996C-NUVQ
SD-996C-U1VQ
Electric Door Strike
with Vertical Adjustment
Manual
SD-996C-U1VQ
• 1,500-lb holding force
• 12 VDC/VAC (SD-996C-U1VQ)
• 12/24 VDC/VAC (SD-996C-NUVQ)
• Tested to 1 million cycles
• Low current draw
250mA@12VDC (SD-996C-U1VQ)
250mA@12VDC & 150mA@24VDC
(SD-996C-NUVQ)
Advertisement
Table of Contents
Related Manuals for SECO-LARM SD-996C-U1VQ
Summary of Contents for SECO-LARM SD-996C-U1VQ
- Page 1 Features: • Vertical adjustable deadbolt opening, sliding • 1,500-lb holding force shim keeper, and deadlatch ramp • 12 VDC/VAC (SD-996C-U1VQ) accommodates a wide range of lock types • 12/24 VDC/VAC (SD-996C-NUVQ) • Accommodates deadbolts up to 1" • Tested to 1 million cycles •...
-
Page 2: Specifications
SECO-LARM Electric Door Strike with Vertical Adjustment Introduction: The SECO-LARM SD-996C-U1VQ and SD-996C-NUVQ Adjustable Door Strikes are compatible with a wide range of lock types including cylindrical, mortise, and mortise exit devices and can be configured for use in wood, aluminum, or metal doors. Included are various ANSI-sized faceplates that can be easily installed on the strike to match the door lock type. - Page 3 SECO-LARM Electric Door Strike with Vertical Adjustment Measuring the Latch Line & Center Lines: 1. Measure the center line of the door. This is shown as “Y” on the diagram to the left. 2. Measure the distance from the door latch to the Center edge of the door frame.
- Page 4 SECO-LARM Electric Door Strike with Vertical Adjustment Preparing the Door Frame: Using the stick-on template as a guide: 1. Drill holes for mounting the strike, and cut a hole for the face-plate size being used. It is recommended to cut the hole slightly smaller than necessary.
-
Page 5: Sample Installations
SECO-LARM Electric Door Strike with Vertical Adjustment Sample Installations: Note: If it is necessary to cut a hole in the frame, mounting tabs may be required to strengthen the installation. See pg. 4. Dead-bolt Latch Installation For installation of SD-996SS-11D1Q and SD-996SS-11D2Q faceplates with the mounting tabs shown in “Mounting the Strike Using Mounting Tabs,”... - Page 6 SECO-LARM Electric Door Strike with Vertical Adjustment Installing the Crimp Connectors: Crimp Crimp connectors are provided to make wiring Connector connections easier and more reliable. To install the connectors: 1. Insert the wires into the connector (see "Wiring Diagram," page 6).
- Page 7 SECO-LARM Electric Door Strike with Vertical Adjustment Strike Adjustment: Adjusting Deadbolt Keeper: Deadbolt Keeper 1. Extend the deadbolt while moving the door closer to the strike, allowing the two to touch. 2. Mark deadbolt limit lines on the strike Down keeper.
-
Page 8: Troubleshooting
LIMITED WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM. This Warranty is...