Advertisement
Quick Links
TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR MAJOR
PROPERTY DAMAGE, READ AND FOLLOW ALL SAFETY
INSTRUCTIONS IN MANUAL AND ON PUMP.
Before installation, you should carefully read
this manual, and pay attention to safety
cautions and instructions in this manual.
Our factory is neither responsible for nor is
reliable for paying compensation for
personal injury, pump damage and other
property losses caused by violation of safety
cautions.
1. GENERAL INFORMATION
1.1. It is applicable to household water supply, equipment
support, pipeline pressurization, garden watering, vegetable
greenhouse watering,fish farming and poultry raising, industrial
and mining, water supply and drainage of enterprises and high-
rise buildings,central air conditioner and centralized heating
circulation system, etc.
1.2. Transfer clean water and other non-corrosive liquids with
low viscosity; do not transport inflammable, explosive, gasified
liquids and liquids containing solid particles or fibers. The PH
value should be within 6.5-8.5.
2. MODEL DESCRIPTION
CEP 05 A 1 6 S
Features S=Standard
Hertz 5=50hz, 6=60Hz
Phase 1=Single phase, 3=Three phase
Voltage A=115V, C=230V, F=110/220V
HPx10
Series Centrifugal Pump
3. TECHNICAL DATA
Max. Flow: 1800L/min
Max. Head: 75m
Output power: 0.25~11kW
Max. Suction: 8 m
Insulation grade: IP44
Protection grade: F
Max. ambient temperature: +40
Max. liquid temperature: +60
4. IMPLEMENTATION STANDARDS
IEC/EN 60335-1 Household and similar electrical appliances-
-safety Part1:General requirements.
IEC/EN 60335-2-41 Household and similar electrical
appliances--safety Part2-41:Particular requirements for pump.
2006/95/EC Low voltage directive
INSTALLATION AND OPERATING INSTRUCTIONS
5. SAFETY PRECAUTIONS
5.1. To ensure normal and
safety operation of the
electric pump, read manual
carefuly before use.
5.3. Do not touch the
electric pump while
working; do not wash,
swim near working area
or let livestock into the
water to avoid accidents.
CEP-C2P
centrifugal pumps
5.2. The electric pump should
ON
OFF
have reliable grounding to
1 1
1 1
0 0
0 0
prevent short circuit; for
safety, leakage protection
switch should be equipped
and be careful no to wet the
power plug; socket should be
connected in damp - proof
area.
5.4. Avoid splashing
pressured water to the
electric pump as well as
prevent the pump immersed
by water.
l
M a n u a
Advertisement
Related Manuals for Pearl CEP-C2P
Summary of Contents for Pearl CEP-C2P
- Page 1 CEP-C2P centrifugal pumps INSTALLATION AND OPERATING INSTRUCTIONS TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR MAJOR PROPERTY DAMAGE, READ AND FOLLOW ALL SAFETY INSTRUCTIONS IN MANUAL AND ON PUMP. Before installation, you should carefully read this manual, and pay attention to safety cautions and instructions in this manual.
-
Page 2: Product Structure
6. PRODUCT STRUCTURE 5.5. Keep the pump in ventilation. 5.6. In case ambient tempera- ture is lower than 4 or the pump is not used for a long time, empty liquid the pipeline system to avoid ice cracking of the pump chamber. Do not operate the pump for a long time without water in it. -
Page 3: Electrical Connection
NEGATIVE SUCTION INSTALLATION PRECAUTIONS FOR INLET PIPELINES 1. While installing the electric pump, do not use too soft rubber CORRECT INSTALLATION tube for the inlet pipeline, avoiding to be sucked flat. 2. The foot valve should be vertically placed and installed 30 cm 1. -
Page 4: Voltage Selector
SINGLE PHASE CONNECTION 110V or 220V 9. START-UP MAINTENANCE Do not start up the pump before the pump chamber is filled with water. CAPACITOR Do not touch the electric pump unless its power has been cut off for at least 5 minutes. Do not dismount the pump body unless water in the pump chamber is empted. -
Page 5: 10.Troubleshooting
10.TROUBLESHOOTING PROBLEM POSSIBLE CAUSE REMEDY Single-phase power supply (three-phase electric motor): a. repair switch contact or replace the switch; a. poor connection of the power switch; b. replace the safety fuse; b. fuse is burned out; c. check and tighten the power connector; c.