Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
CHRYSLER4
Designed by Installers for Installers
© 2019 Directed, Vista CA
This product is intended for installation by a professional installer only! Attempts to install this
product by a person other than a trained professional may result in severe damage to a vehicle's
electrical system and components.
2019-05-15
Directed Digital
Solutions
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Directed DIRECTECHS CHRYSLER4
Summary of Contents for Directed DIRECTECHS CHRYSLER4
- Page 1 CHRYSLER4 Designed by Installers for Installers © 2019 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
-
Page 2: Table Of Contents
Contents Warning! Safety first ........................3 Introduction ............................ 4 Pre-installation and application warnings ..................4 Vehicle application guide ......................5 Wiring connections ......................... 6 Main power harness (H1), 12-pin thick gauge connector ............... 6 Auxiliary output harness (H2), 16-pin black connector ..............6 Analog harness (H3), 18-pin white connector ................ -
Page 3: Warning! Safety First
The following safety warnings must be observed at all times: • Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. • When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. -
Page 4: Introduction
Introduction The CHRYSLER4 firmware for Directed Digital Solutions is compatible with specific Chrysler, Dodge/Ram and Jeep vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module using CHRYSLER4. If you would prefer using this system as a digital solution, go to www.directechs.com and search for the make, model and... -
Page 5: Vehicle Application Guide
DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote PK: Transponder & Immobilizer Override RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved. -
Page 6: Wiring Connections
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved. -
Page 7: Analog Harness (H3), 18-Pin White Connector
If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. The Green wire is only required for starter disable and anti-grind applications. Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved. -
Page 8: Installation (Wiring Diagrams & Vehicle Wiring Reference Charts)
(-) Driver’s Door Trigger: Violet, pin 6 Resistor 2100Ω (+) 12V: Violet/Red, pin 5 (MUX) Parking Light: White/Brown, pin 11 Headlight Switch (black conn. headlight switch) BCM Power Connector (Black top conn. at BCM) Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved. - Page 9 SKIM (Sentry Key Immobilizer Module) Black Immo. Ignition Pink/White SKIM (Sentry Key Immobilizer Module) Black Parking Lights White/Orange Drivers kick panel. Driver Door Trigger Violet Third connector from top of BCM. Black Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved.
-
Page 10: Type 2
1 & 7: White: (+) Parking Light Output Resistor 1K Ω Headlight switch (Black conn. at headlights) (+) 12V: Violet/Red, pin 5 MUX Parking Lights: Brown/White, pin 6 BCM Power Connector (Black top conn. at BCM) Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved. - Page 11 SKIM (Sentry Key Immobilizer Module) Black Immo. Ignition Pink/White or Pink/Gray SKIM (Sentry Key Immobilizer Module) Black Parking Lights Brown/White Headlight switch. Black Driver Door Trigger Violet Drivers Door Module Black Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved.
-
Page 12: Type 3
(-) Drivers Door Trigger: Violet, pin 4 Module-Sentry Key J1850: SKIM (Sentry Key Immobilizer Module) White/Violet, Ignition (black connector at ignition switch) pin 2 Cylinder (black top connector on BCM) Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved. - Page 13 Pink/Lt. Green or White/ Immo. Ignition SKIM (Sentry Key Immobilizer Module) Black Violet Parking Lights Pink/Red Bottom connector on BCM Gray Driver Door Trigger Violet Top connector on BCM Gray Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved.
-
Page 14: Connecting The Module
Manual or automatic transmission selection The yellow loop on the Directed Digital Solutions controls which transmission type the unit is configured for. The state of the loop (uncut or cut) when the main module is powered up will determine which type is selected. -
Page 15: Optional Sensors
When flashing the Directed Digital Solutions, make sure to pick the remote you will be using. This way the main module will have the necessary firmware to interact with the remote and Control Center (antenna) combination. -
Page 16: Module Programming
Connect all but the 12-pin harness Connect all the harnesses to the Directed Digital Solutions, EXCEPT the 12-pin main power harness. Must be connected LAST Connect the 12-pin main power harness, and wait until the LED turns ON solid red. -
Page 17: Led Diagnostics And Troubleshooting
External module synchronization Description Troubleshooting OBDII feature not supported. The diagnostic data bus was not detected, therefore the SmartStart features will be limited. (Flashes red, red, then orange) x 10 Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved. - Page 18 The vehicle was detected as moving, which prevents the system from shutting it down. Flashes red x 4 Analog error codes Description Troubleshooting DEI feature error. A feature config file mismatch was detected. Please contact Technical Support. Flashes red, green & orange Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved.
-
Page 19: Soft Reset
A module reset will only erase the steps performed in "Module programming" on page 16. The firmware and settings flashed to the module will not be affected. Connect all but the If required for your installation, connect all the harnesses to the Directed Digital Solutions, 12-pin harness EXCEPT the 12-pin main power harness. Press and hold the programming button, then connect the 12-pin harness to the module. -
Page 20: Learning The Tach (Not Needed With Virtual Tach)
Important! After successfully learning Virtual Tach, a small minority of vehicle starters may over crank or under crank during remote start. Use the VirtualTach Fine tune feature in the configuration wizard to adjust the starter output time in 50mS increments to compensate for such an occurrence. Directed Digital Solutions CHRYSLER4 © 2019-05-15 Directed. All rights reserved. -
Page 21: Limited Lifetime Consumer Warranty
Directed dealer, the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address;... -
Page 22: Quick Reference Guide
Factory remote. Press the Remote Start button on the transmitter.* • Aftermarket remote. • Directed SmartStart application via your smartphone. & The parking lights will flash once to indicate the Parking lights flash x1 Press Remote vehicle is now in Pit Stop Mode. - Page 23 SmartStart compatible This system is compatible with Directed SmartStart. For a complete list of supported features, please visit www.mysmartstart.com. What is SmartStart? Now you can remote start, lock and unlock your car just by pushing a button on your mobile device; using the SmartStart App from Directed, the leader in vehicle security and remote start.
Need help?
Do you have a question about the DIRECTECHS CHRYSLER4 and is the answer not in the manual?
Questions and answers