Balboa GL Series User Manual
  1. Manuals
  2. Brands
  3. Balboa Manuals
  4. Control Panel
  5. GL Series
  6. User manual

Balboa GL Series User Manual

Hide thumbs Also See for GL Series:
Table of Contents

Advertisement

Quick Links

EL/GL Series - Mach 3
ML551/ML554 User Guide
Light
Light
Jets 1
Jets 2
Note regarding EL and GL systems: Mach 3 EL and GL systems function
identically, but conform to different International requirements. This
user guide will refer to EL systems for the sake of simplicity, but the
information given applies to both EL and GL products.
900854
Mode
Blower
L
L
L
Li
Li
L i
L
L i
L
L
Light
Light
L
L
L
L
L
Li
L
Li
L
Li
Lig
Li
Li
Li
Li
Li
Li
i
i g
i
i
i
i
i
i
i
i
i
i
i
i
g
g
g
g
g
g h
g
g
g
g
g
g
g
gh
ght
g
ght
gh
gh
gh
gh
gh
gh
gh
gh
gh
gh
h
h
h
h
h
h
h
h
h
h
h
h
t
t
t
t
t
t
t
t
t
t
t
t
Jets 1
Jets 2
Blower
Warm
Warm
Heat
Heat
Cool
Mo
M
Mod
Mo
Mo
M
Mo
Mo
Mo
Mo
M o
M
Mode
d
d
de
d e
de
de
de
de
de
de
de
Warm
Warm
Heat
Heat
Cool

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GL Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Balboa GL Series

Summary of Contents for Balboa GL Series

  • Page 1 EL/GL Series - Mach 3 ML551/ML554 User Guide Light Light Mode Warm Warm Heat Heat Jets 1 Jets 2 Blower Cool Light Light Mode Warm Warm Heat Heat Jets 1 Jets 2 Blower Cool Note regarding EL and GL systems: Mach 3 EL and GL systems function identically, but conform to different International requirements.

  • Page 3: Table Of Contents

    Clean-up Cycle ....3 EL/GL SERIES (Mach 3) CONTROL ..1 Circ Pump ......4 Initial Start-up .

  • Page 4: Temp Set

    Temp Set (80°F - 104°F / 26.0°C - 40.0°C) Jets 1 The last measured temperature is constantly displayed Press the “Jets 1” button once to turn pump 1 on or off, on the LCD. Your spa’s set temperature range may and to shift between low and high speeds if equipped.

  • Page 5: Preset Filter Cycles

    Preset Filter Cycles Circ Pump (optional) On all systems, the pump and the ozone generator will If your system is equipped with a circ pump, it may be run during filtration. At the start of each filter cycle, the configured to work in one of three different ways: blower will run briefly on its highest speed to purge the 1) The circ pump operates continuously (24 hours) with air channels.

  • Page 6: Displaying Information About Your Spa

    Displaying Information About Your Spa – Dolphin II Address When set to “ ”, no addressing is used. Use this There are several pieces of information about your setting for a Dolphin I, or for a Dolphin II which is spa that can be called up from the panel, but are only set for no address (which is the Dolphin II factory needed in special cases.

  • Page 7: Gfci Protection

    Note: The GFCI section does not apply on EL systems used outside the United States. This GFCI section does not apply to GL Systems. GFCI Protection GFCI Trip Test Procedure Your spa may be equipped with a GFCI Protection The installer can cause the GFCI Trip Test to feature.

  • Page 8: Diagnostic Messages

    Diagnostic Messages Message Meaning Action Required No message on display. The control panel will be disabled until power returns. Power has been cut off to the spa. Time of day will be preserved for 30 days with a battery back-up on EL8000 and EL5000 systems. EL1000 and some EL2000 systems reset the time of day on each power-up.
  • Page 9 Diagnostic Messages (continued) Message Meaning Action Required Temperature unknown. After the pump has been running for 1 minute, the temperature will be displayed. Temperature not current in Economy or In Economy or Sleep mode, the pump may be off for Sleep mode.

  • Page 10: Periodic Reminder Messages

    Periodic Reminder Messages (Press the “Mode” button to reset a displayed reminder.*) Message ** Frequency *** Action Required Every 7 days Test and adjust pH chemical levels per manufacturer’s instructions. Every 7 days Test and adjust sanitizer chemical levels per manufacturer’s instructions. Every 30 days Remove, clean, and reinstall filter per manufacturer’s instructions.

  • Page 11: Optional Auxiliary Panels

    Optional Auxiliary Panels Note: Below is a partial list of optional auxiliary panels and their basic functions. Please contact for local dealer for a complete list of options that will work with your spa. Jets 1 Jets 1 Jets 1 Jets 1 Jets 2 Blower...

  • Page 12: Basic Installation Guidelines

    Warning! Qualified technician required for service and installation. Basic Installation and Configuration Guidelines for Mach 3 CSA Compliance/Conformité EL-Series Spa Controllers. Caution: Use minimum 6AWG copper conductors only. the spa. Torque field connections between 21 and 23 in lbs. Readily accessible disconnecting means to be provided at time of installation.

This manual is also suitable for:

El seriesMl551Ml554

Table of Contents