Cleaning The Body - Makita DRC200PT Instruction Manual

Cleaning the body

1. Wipe the Robotic Cleaner's exterior with a cloth
slightly moistened with mild detergent.
2. Press and release the top lid (Fig. K-1) to unlock,
and then fully open the lid.
3. Take out the dust box (Fig. K-2).
4. Wipe the Robotic Cleaner's interior (Fig. R-1)
including the vent grill (Fig. R-2) with a cloth slightly
moistened with mild detergent.
RESTORING THE
ROBOTIC CLEANER
When the Robotic Cleaner cannot continue to operate
under such conditions as drive wheel hanging down or
running out of battery power, the Robotic Cleaner will
stop cleaning and tell you something is wrong by the
following lamps and buzzers.
• Troubleshooting lamp (Fig. F-2)
• Filter maintenance lamp (Fig. F-3)
• Brush maintenance lamp (Fig. F-4)
• Timer lamps (Fig. F-6)
• Buzzer lamp (Fig. F-9)
• Vacuum lamp (Fig. F-10)
• Boundary sensor lamp (Fig. F-11)
1. Identify the problem using the following table.
2. Resolve the problem.
3. Press the POWER button (Fig. F-8) on the
Robotic Cleaner or the
G-2) on the remote control to enter standby mode.
The error indication stops and the Robotic Cleaner
is ready for cleaning.
NOTICE: If the error occurs again, turn OFF and ON
the Robotic Cleaner.
NOTICE: If the problem persists after the remedial
action is complete, consult your nearest Makita
Service Center.
Indication
• The drive wheel is hanging down.
• The Robotic Cleaner has gotten stuck
on a barrier.
• The Robotic Cleaner has been
lamp flashes
exposed to direct sunlight.
once, twice, or
• The Robotic Cleaner has stopped on a
6 times for each
black floor.
sequence
Move the Robotic Cleaner away from
the area.
If the error occurs again, clean the cliff
sensors (Fig. O-1).
lamp flashes
• A bumper sensor error has occurred.
3 times for each
Push the bumper (Fig. P-2) 10 times.
sequence
Start/Stop button (Fig.
Cause/Remedy
lamp flashes
4 times for each
sequence
lamp flashes 5
or 7 times for each
sequence
and
lamps flash once
for each sequence
and
all lamps flash
once for each
sequence
and lamps
light up
and lamps
light up
and lamps
light up
lamp flashes
once for each
sequence
lamp
lights up
16 ENGLISH
• Threads and hairs are tangled with the
drive wheels.
Remove them from the drive wheels
(Fig. M-2).
• The Robotic Cleaner passed through
a confined area where its top surface
was pushed down.
This is not a malfunction.
• The Robotic Cleaner has overheated.
Turn the Robotic Cleaner OFF,
remove the battery cartridge(s), and
wait for an hour. Use the Robotic
Cleaner only at room temperatures
not exceeding 40°C (104°F).
• The dust box or the filter has not been
installed.
Install the dust box or the filter.
• The remaining battery charge was
not enough ( or
cleaning.
Fully charge the battery cartridges.
• Threads and hairs are tangled in the
drive wheels.
Remove them from the drive wheels
(Fig. M-2).
• The Robotic Cleaner passed through
a confined area where its top surface
was pushed down.
This is not a malfunction.
• A sensor error has occurred.
Turn the Robotic Cleaner OFF and
then ON.
• An error has occurred in the Robotic
Cleaner.
Turn the Robotic Cleaner OFF and
then ON.
• Threads and hairs are tangled in the
side brushes and main brush.
Remove them from the brushes (Figs.
A, N-3).
• The dust box is full of dust and dirt or
the filter is clogged.
Empty the dust box (Fig. K-2) and
clean the filter (Fig. K-5).
) to start