Table of Contents
Advertisement
Available languages
Available languages
English
To Attach the Dust Bag (Fig. K)
1. While holding the saw, fit the dust bag collar
extraction port
as shown in Figure K.
24
2. Turn the collar
26
clockwise to lock the dust bag
in place.
To Empty the Dust Bag (Fig. K)
1. While holding the saw, turn the collar
to unlock the dust bag
25
2. Remove dust bag from the saw and gently shake or tap the
dust bag to empty.
3. Reattach the dust bag back onto the dust extraction port
and lock into place by turning the dust bag collar clockwise.
You may notice that all the dust will not come free from the
bag. This will not affect sanding performance but will reduce
the saw's dust collection efficiency. To restore your saw's dust
collection efficiency, depress the spring inside the dust bag
when you are emptying it and tap it on the side of the trash can
or dust receptacle.
Workpiece Support (Fig. L, M)
WARNING: To reduce the risk of serious personal injury,
support the work properly and hold the saw firmly to
prevent loss of control.
Figure L shows proper sawing position. Figure M shows an
unsafe condition. Hands should be kept away from cutting area.
To avoid kickback, ALWAYS support board or panel NEAR the
cut. DON'T support board or panel away from the cut .
ALWAYS DISCONNECT SAW BEFORE MAKING ANY
ADJUSTMENTS! Place the work with its "good" side—the one
on which appearance is most important—down. The saw cuts
upward, so any splintering will be on the work face that is up
when you saw it.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
14
26
to the dust
25
26
counterclockwise
.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the plastic materials used in
these parts. Use a cloth dampened only with water and
mild soap. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
Lower Guard
The lower guard should always rotate and close freely from
a fully open to fully closed position. Always check for correct
operation before cutting by fully opening the guard and letting
it close. If the guard closes slowly or not completely, it will
need cleaning or servicing. Do not use the saw until it functions
correctly. To clean the guard, use dry air or a soft brush to
remove all accumulated sawdust or debris from the path of
the guard and from around the guard spring. Should this not
correct the problem, it will need to be serviced by an authorized
service center.
Optional Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
Rechargeable Battery Pack
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done
before. At the end of its technical life, discard it with due care for
our environment:
•
Run the battery pack down completely, then remove it from
the tool.
•
Li‑Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
recycled or disposed of properly.
WALT recommended
e
Advertisement
Table of Contents
