Specifications - Makita DA001GZ01 Instruction Manual

SPECIFICATIONS

Model:
Gear speed
Drilling capacities
(Diameter)
No load speed
Overall length (with battery cartridge BL4040)
*With the front handle extended
Rated voltage
Net weight
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
Only for EU countries
Ni-MH
Do not dispose of electric equipment or
Li-ion
battery pack together with household waste
material!
In observance of the European Directives,
on Waste Electric and Electronic
Equipment and Batteries and Accumulators
and Waste Batteries and Accumulators
and their implementation in accordance
with national laws, electric equipment and
batteries and battery pack(s) that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for drilling in wood, metal and
plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-1:
Sound pressure level (L
Sound power level (L ) : 95 dB (A)
WA
Uncertainty (K) : 3 dB(A)
Steel
Wood
) : 84 dB(A)
pA
High
Auger bit: 50 mm
Self-feed bit: 65 mm
Hole saw: 105 mm
-1
0 - 1,500 min
D.C. 36 V - 40 V max
BL4020 / BL4025* / BL4040* / BL4050F*
* : Recommended battery
DC40RA / DC40RB / DC40RC
NOTE: The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-1:
Work mode: drilling into metal
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
2 ENGLISH
DA001G
Low
13 mm
Auger bit: 50 mm
Self-feed bit: 118 mm
Hole saw: 159 mm
0 - 400 min
545 mm
* 614 mm
5.6 - 6.2 kg
2
) : 2.5 m/s or less
h,D
2
-1