Table of Contents
Advertisement
Quick Links
Check out what else you can get from Martindale:
G
16th Edition Testers
G
Accessories
G
Calibration Equipment
G
Continuity Testers
G
Electricians' Kits
G
Environmental Products
G
Full Calibration & Repair Service
G
Fuse Finders
G
Digital Clamp Meters
G
Digital Multimeters
G
Labels
G
Microwave Leakage Detectors
Trusted by Professionals
Martindale Electric Company Limited
Metrohm House, Penfold Trading Estate, Imperial Way, Watford WD24 4YY, UK
Tel: +44(0)1923 441717 Fax: +44 (0)1923 446900
E-mail: sales@martindale-electric.co.uk
Website: www.martindale-electric.co.uk
© Martindale Electric Company Ltd. 2006
Registered in England No. 3387451. Rev 4 LITIN2103
G
Motor Maintenance Equipment
G
Multifunction Testers
G
Non-trip Loop Testers
G
Pat Testers & Accessories
G
Phase Rotation Testers
G
Proving Units
G
Socket Testers
G
Thermometers & Probes
G
Test Leads
G
Voltage Indicators
G
Specialist Metrohm Testers (4 & 5kV)
G
Specialist Drummond Testers
IN2103
INSULATION TESTER
I
NSTRUCTION
M
ANUAL
MARTINDALE
E L E C T R I C
Trusted by Professionals
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MARTINDALE IN2103
Summary of Contents for MARTINDALE IN2103
- Page 1 IN2103 INSULATION TESTER Check out what else you can get from Martindale: NSTRUCTION 16th Edition Testers Motor Maintenance Equipment Accessories Multifunction Testers ANUAL Calibration Equipment Non-trip Loop Testers Continuity Testers Pat Testers & Accessories Electricians’ Kits Phase Rotation Testers Environmental Products Proving Units Full Calibration &...
- Page 2 Where applicable other safety measures such as use of protective gloves, goggles etc. should be employed. Please keep these instructions for future reference. Updated instructions and product information are available at: www.martindale-electric.co.uk/instruct REMEMBER: SAFETY IS NO ACCIDENT MEANING OF SYMBOLS:...
-
Page 3: Table Of Contents
Thank you for buying one of our products. For safety and full For user notes understanding of its benefits please read this manual before use. Technical support is available from 01923 441717 and support@martindale-electric.co.uk. CONTENTS Introduction Inspection Description Product Specific Safety Information... -
Page 4: Introduction
±(3% rdgs +5d) 1.2 Description 1000V 4/40/400/5000MΩ The IN2103 Digital Insulation and Continuity Tester is designed to perform testing in accordance with international standards, Short circuit current: <1.5mA including BS7671. Insulation testing can be undertaken at Auto-Discharge: when TEST button released 250/500/1000V DC. - Page 5 PI (Polarization Index) DAR (Dielectric Absorption Ratio) Auto Power Off: user selectable (default 5 mins) READ PI DAR AUTO HOLD SHIFT LIMIT APO (Auto Power Off) disable option mGΩ KMΩ 99-result Memory Safety: Complies with BS EN 61010 and BS EN 61557 ZERO A - H Overvoltage Category: CAT III 600V, Pollution Degree 2.
-
Page 6: Product Specific Safety Information
2. PRODUCT SPECIFIC SAFETY INFORMATION Specification MARTINDALE Safety: Complies with BS EN 61010 and BS EN 61557 IN2103 Overvoltage Category: CAT III 600V, Pollution Degree 2. E L E C T R I C Insulation Tester This tester has been designed with your safety in mind, however, no design can completely protect against incorrect use. -
Page 7: Operation
Since some jurisdictions do not allow limitation of the term of an 3. OPERATION implied warranty, or exclusion or limitation of incidental or 3.1 Installing or Replacing Batteries consequential damages, the limitations and exclusions of this warranty may not apply to every buyer. If any part of any provision of WARNING this warranty is held invalid or unenforceable by a court or other When the meter shows the "... -
Page 8: How It Works
5. WARRANTY AND LIMITATION OF LIABILITY the red and black leads across the circuit to be measured - the This Martindale product is warranted to be free from defects in measured voltage will be displayed. material and workmanship under normal use and service. The... -
Page 9: Maintenance
There are no user serviceable parts in this unit other than those For safety reasons, please adhere to the following procedure for that may be described in section 3. Return to Martindale Electric if Insulation Resistance Measurement: faulty. Our service department will quote promptly to repair any Ensure that the TEST button is unlatched and is released. - Page 10 Press the TEST button to apply the test voltage. This button can Setting Lower Limit be turned clockwise while pressed to latch it. Allow several After exiting the Upper Limit set up, the Lower Limit set up is seconds for the reading to stabilise. The test voltage is shown in automatically entered.
- Page 11 LIMITS key Operating procedure for PI Press this key to enable or disable the "out of limits" alarm. This Set rotary switch to 250/500/1000V. Clear the memory before function causes an alarm to sound if the measured value is not making a PI measurement.
- Page 12 Note: It is a good idea to do a battery check before making PI and The PI memory locations are 00 to 15 in the PI MEM view, DAR measurements. location 00 is the PI value. The other 15 are records of individual tests, taken as part of the PI measurement set.
Need help?
Do you have a question about the IN2103 and is the answer not in the manual?
Questions and answers