Table of Contents
Advertisement
Quick Links
799000855 / Rev. 0 / 2018-12-18
Translation of the original operating manual
Operating Manual
SERIES EMSC2/LMSC2
Magnetic Linear Encoder with 1 Vpp Sine/Cosine Outputs
EMSC is only functional with the ELGO MB20-20 magnetic tape (2 mm pole pitch)!
LMSC is only functional with the ELGO MB20-50 magnetic tape (5 mm pole pitch)!
Compact incremental magnetic sensors with integrated evaluation circuit
and speed proportional sine/cosine outputs
- EMSC: 2 mm measurement movement ≙ 1 signal period
- LMSC: 5 mm measurement movement ≙ 1 signal period
Distance to magnetic tape max. 0.8 mm (EMSC) / max. 2 mm (LMSC)
Non-contact and wear-free magnetic measuring principle
Suitable for linear and radial measurement applications
Advertisement
Table of Contents
Related Manuals for ELGO Electronic EMSC2 Series
Summary of Contents for ELGO Electronic EMSC2 Series
- Page 1 799000855 / Rev. 0 / 2018-12-18 Translation of the original operating manual Operating Manual SERIES EMSC2/LMSC2 Magnetic Linear Encoder with 1 Vpp Sine/Cosine Outputs EMSC is only functional with the ELGO MB20-20 magnetic tape (2 mm pole pitch)! LMSC is only functional with the ELGO MB20-50 magnetic tape (5 mm pole pitch)! ...
- Page 2 +49 (0) 7731 9339 – 0 +49 (0) 7731 2 13 11 info@elgo.de Document- No. 799000855 Document- Name EMSC-LMSC2-000-MA-E_51-18 Document- Revision Rev. 0 Issue Date 2018-12-18 Copyright © 2018, ELGO Electronic GmbH & Co. KG - 2 -...
-
Page 3: Table Of Contents
Contents 1 Contents Contents ..................... 3 List of Figures ..................4 List of Tables ..................4 General, Safety, Transport and Storage ........... 5 Information Operating Manual ................5 Explanation of Symbols ..................5 Statement of Warranties ..................6 Demounting and Disposal ..................6 General Causes of Risk .................. -
Page 4: List Of Figures
Contents Type Designation ................22 10.1 Accessories ...................... 22 Index ....................23 2 List of Figures Figure 1: Magnetic tape ..........................8 Figure 2: Representation of the Waveforms ....................9 Figure 3: Example of a follow-up circuit ...................... 9 Figure 4: Dimensions Sensor ........................10 Figure 5: Alignment of the Sensor ...................... -
Page 5: General, Safety, Transport And Storage
General, Safety, Transport and Storage 4 General, Safety, Transport and Storage Information Operating Manual This manual contains important information regarding the handling of the device. For your own safety and operational safety, please ob- serve all safety warnings and instructions. Precondition for safe operation is the compliance with the specified safety and handling instruc- tions. -
Page 6: Statement Of Warranties
General, Safety, Transport and Storage Statement of Warranties The producer guarantees the functional capability of the process engineering and the selected parameters. Demounting and Disposal Unless acceptance and disposal of returned goods are agreed upon, demount the device considering the safety instructions of this manual and dispose it with respect to the environment. -
Page 7: Conventional Use
General, Safety, Transport and Storage Conventional Use The ELGO-device is only conceived for the conventional use described in this manual. The ELGO length measuring system EMSC2/LMSC2 only serves to measure lengths, positions and distances. CAUTION! Danger through non-conventional use! Non-intended use and non-observance of this operating manual can lead to dangerous situations. Therefore: Only use the device as described ... -
Page 8: Product Features
Product Features 5 Product Features The EMSC2/LMSC2 is an incremental magnetic length measur- ing system with 1 Vpp sine/cosine outputs. The sensor technology and evaluation electronics are located in a compact housing, which can be mounted horizontally or (if option L is ordered) vertically to the magnetic tape. -
Page 9: Representation Of The Waveforms
Product Features Representation of the Waveforms Um (sin) Distance ᵠ Mechanical angle Differential signal (sin - sin) Um (cos) Distance ᵠ Mechanical angle Differential signal (cos - cos) Figure 2: Representation of the waveforms 5.3.1 Example of a follow-up circuit 120 Ω... -
Page 10: Technical Data
Technical Data 6 Technical Data Identification The type label serves for the identification of the unit. It is located on the housing of the sensor and gives the exact type designation (=order reference, 10) with the corresponding part number. Furthermore, the type label contains a unique, traceable device number. -
Page 11: Technical Data Sensor
Technical Data Technical Data Sensor EMSC2/LMSC2 (Standard Version) Mechanical Data Measuring principle incremental Repeat accuracy depending on evaluation electronics System accuracy in µm at 20° C EMSC: ± (20 + 20 x L) (L = measuring length in m) LMSC: ± (25 + 20 x L) Distance sensor - magnetic tape EMSC: max. -
Page 12: Technical Data Magnetic Tape
Technical Data Technical Data Magnetic Tape The magnetic tape consists of two components: The actual magnetic tape which carries the position information A mechanical stainless steel back iron Magnetic Tape MB20-20-10-1-R and MB20-50-10-1-R Coding incremental, single track system Pole pitch MB20-20-10-1-R: 2 mm MB20-50-10-1-R: 5 mm... -
Page 13: Installation And First Start-Up
Installation and First Start-Up 7 Installation and First Start-Up CAUTION Please read the operating manual carefully before using the device! Strictly observe the Instal- lation instructions! In case of damage caused by failure to observe this operating manual, the warranty expires. ELGO is not liable for any secondary damage and for damage to persons, property or assets. -
Page 14: Installation Of The Sensor
Installation and First Start-Up Installation of the Sensor For mounting the sensor two M3 screws are required. Observe the mounting tolerances stated in section 7.2.2. 7.2.1 Alignment of Sensor / Magnetic Tape Since the active sensor surface is not in the center of the sensor housing, it should be ensured that the sensor head is aligned and mounted such that the active sensor surface is in the middle of the magnetic tape. - Page 15 Installation and First Start-Up 7.2.2 Mounting Tolerances The tolerances apply equally to both mounting variants resp. regardless of whether the sensor is mounted hori- zontally (standard) or vertically (option L). Table 1: Mounting tolerances Tolerances Sensor distance to the tape EMSC: 0.1 …...
-
Page 16: Installation Of The Magnetic Tape
Installation and First Start-Up Installation of the Magnetic Tape NOTE External Magnetic Fields The magnetic tape must not be influenced by external magnetic fields! The magnetic tape must not come into direct contact with other magnetic fields (e.g. perma- nent magnets, magnetic clamps, electromagnets, magnetic stands)! This may cause irrepara- ble damage, which will compromise the measuring accuracy or even the functioning. - Page 17 Installation and First Start-Up 7.3.2 Handling In order to avoid tension in the tape, it must not be stretched, compressed or twisted. It should be stored with the magnetized plastic tape to the outside (see Figure 8), the minimum bending radius must be noted here Magnetized Plastic tape...
- Page 18 Installation and First Start-Up The tape must be glued smoothly on the surface. The measuring accuracy decreases if the tape is not even! Before gluing the magnetic tape and the cover tape onto the surface, they should be left lying on the mounting surface for ca.
-
Page 19: Connections
Connections 8 Connections Cable and Pin Assignment Table 3: Pin Assignment open cable ends Drawing Color Function Description white 0 VDC Open cable ends: brown + 5 VDC green* SIN+ sine positive violet* SIN− sine negative black* COS+ cosine positive grey* COS−... -
Page 20: Disturbances, Maintenance, Cleaning
Disturbances, Maintenance, Cleaning 9 Disturbances, Maintenance, Cleaning This chapter describes possible causes for disturbances and measures for their removal. In case of increased disturbances, please follow the measures for fault clearance in chapter 9.1. In case of disturbances that cannot be eliminated by following the advice and the fault clearance measures given here, please contact the manufacturer (see second page). -
Page 21: Maintenance
Disturbances, Maintenance, Cleaning Maintenance The device is maintenance-free. Cleaning WARNING! The device can only be cleaned with a damp cloth, do not use aggressive cleanser! - 21 -... - Page 22 Type Designation 10 Type Designation X MSC 2 - 000 01.5 Measuring System: EMSC = for MB20-20 (pole pitch = 2 mm) LMSC = for MB20-50 (pole pitch = 5 mm) Sensor Design: = compact sensor head with integrated evaluation circuit Version: = standard version = first special version (etc.)
- Page 23 Index 11 Index Accessories ............. 22 Maintenance ..........20, 21 Accident prevention regulations......5 Mounting Tolerances ........15 Alignment of Sensor / Magnetic Tape ....14 Operating area ..........13 Causes of risk ............ 6 Operational safety ..........5 Cleaning ........... 20, 21 Order reference ..........
- Page 24 Document-No.: 799000855 / Rev. 0 ELGO Electronic GmbH & Co. KG Measuring | Positioning | Control Document-Name: EMSC-LMSC2-000-MA-E_51-18 Carl - Benz - Str. 1, D-78239 Rielasingen Subject to change - © 2018 Fon:+49 (0) 7731 9339-0, Fax:+49 (0) 7731 28803 Internet: www.elgo.de, Mail: info@elgo.de...