Related Manuals for Lantech TWAP-5004
Summary of Contents for Lantech TWAP-5004
- Page 1 TWAP-5004 EN50155 Multifunction VPN Router w/up to 2x WiFi 11ac + 2 serial ports** + 4 Gigabit X-coded Ethernet Switch + 2WAN/2LAN User Manual (Hardware) Dec. 2019 **optional...
- Page 2 Recommendation for Shielded network cables STP cables have additional shielding material that is used to reduce external interference. The shield also reduces the emission at any point in the path of the cable. Our recommendation is to deploy an STP network cable in demanding electrical environments. Examples of demanding indoor environments are where the network cable is located in parallel with electrical mains supply cables or where large inductive loads such as motors or contactors are in close vicinity to the camera or its cable.
- Page 3 Lantech Communications Global Inc. Products offered may contain software which is proprietary to Lantech Communications Global Inc. The offer or supply of these products and services does not include or infer any transfer of ownership.
- Page 4 FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
-
Page 5: Table Of Contents
Content Chapter 1 Hardware Description......5 Physical Dimension ........5 Package Content: ......... 8 IP Protection ..........8 LED Indicators ..........11 Chapter 2 Hardware Installation ......13 Hardware installation........13 Chapter 3 Console Management......18 3.1. Connecting to the Console Port....18 3.2. -
Page 6: Chapter 1 Hardware Description
Chapter 1 Hardware Description In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling information, and wiring installation. 1.1 Physical Dimension Aluminum case. IP-65/54, 178mm(W)x99mm(H)x103mm(D) With 2 serial ports... - Page 7 Without 2 serial ports...
- Page 8 Port description of IP-65/54 series switch With 2 serial ports Without 2 serial ports...
-
Page 9: Package Content
1.2 Package Content: Multifunction Router x1 Console cable x1 1.3 IP Protection The IP Code, Ingress Protection Rating, sometimes also interpreted as International Protection Rating, classifies and rates the degree of protection provided against the intrusion (including body parts such as hands and fingers), dust, accidental contact, and water in mechanical casings and with electrical enclosures. - Page 10 not enter in sufficient quantity to interfere with the satisfactory operation of the equipment; complete protection against contact No ingress of dust; complete protection against Dust tight contact Liquid ingress protection The second digit indicates the level of protection that the enclosure provides against harmful ingress of water.
- Page 11 harmful effect. Pressure: 80–100 kPa Water jets Water projected by a Test duration: at least nozzle (6.3 mm) against 15 minutes enclosure from any Water volume: 12.5 litres direction shall have no per minute harmful effects. Pressure: 30 kPa at distance of 3 m Powerful Water projected in...
-
Page 12: Led Indicators
but only in such a manner that it produces no harmful effects. — Powerful Protected against close- high range high pressure, high temperature temperature spray downs. water jets 1.4 LED Indicators The diagnostic LEDs that provide real-time information of system and optional status are located on the front panel of the industrial switch. - Page 13 WLAN is inactive Blinking The serial is transmitting or receiving data. Serial 1 & Green Serial 2 Serial is inactive...
-
Page 14: Chapter 2 Hardware Installation
Chapter 2 Hardware Installation Hardware installation 2.1.1Unpack switch and check the accessory with packing content list 2.1.2 Mount the switch on desired position. For the best ventilation, it is suggested to mount the switch on metallic surface. 2.1.3 Connect the M12 connector of power input. ... - Page 15 report a power failure. You can disable this power fail event via web browser. Pin assignment of DI/DO 2.1.4 Fitting the device, grounding Install the system in a dry and clean area to protect the switch to get exposed with dirt. Plug the connector to the power supply plug then turn on the power supply.
- Page 16 Ground screw of router 2.1.5 Connect the M12 Ethernet connector with RJ-45 data cable, ports are not used shall be caped that comes with the package to insulate the surrounding. Pin assignment of M12 10/100/1000T network connector...
- Page 17 Note: The protection class IP65/54 is only achieved when bolted together. The other components attaching to the system have to meet with the IP65/54 protection class in order to reach the whole system IP65/54 protection. Empty ports must be sealed with the protective caps supplied. 2.1.6 Connect the M12 serial connector with RS232/RS422/RS485 cable, ports are not used shall be caped that comes with the package to insulate the surrounding.
- Page 18 2.1.8 Connect the M12 connector to USB if needed Note: The USB port is USB 2.0 speed, not USB 3.0...
-
Page 19: Chapter 3 Console Management
Chapter 3 Console Management 3.1. Connecting to the Console Port The supplied cable which one end is M12 8-pole connector and the other end is RS-232 connector. Attach the end of RS-232 connector to PC or terminal and the other end of M12 connector to the console port of the switch. - Page 20 Flow control: None The settings of communication parameters Having finished the parameter settings, click ‘OK’. When the blank screen shows up, press Enter key to have the login prompt appears. Key in ‘admin’ (default value) for both User name and Password (use Enter key to switch), then press Enter and the Main Menu of console management appears.