Advertisement
5.
To adjust the position of the seat, remove
the adjustment knob (a) on the bottom
of the seat (b). Slide the seat (b) forward
or backward as desired. Reinstall the
adjustment knob (a). See Figure 2-6.
Dash Shroud (If Equipped)
There are two shroud types. One shroud for the
1/3/5/K/T-Style and one for the S-Style dash.
Continue below for the 1/3/5/K/T-Style, skip ahead
to the S-style section for the S-style dash.
1/3/5/K/T-Style Dash
1.
If the dash shroud (a) was shipped loose, the
hardware for attaching the dash shroud (a) is
shipped installed in the dash (c). Remove the
two bolts (b) from the dash (c) . See Figure 2-7.
(a)
(b)
(b)
(a)
Figure 2-7
2.
Mount the dash shroud (a) and align the
mounting holes. See Figure 2-7.
3.
Secure the dash shroud (a) to the dash (c)
with the bolts (b) removed in Step 1. See
Figure 2-7.
S-Style Dash
1.
If the dash shroud (a) was shipped loose, the
hardware for attaching the dash shroud (a) is
shipped installed in the dash shroud (a) and the
dash (b). Remove the two bolts (c) and washers
(d) from the dash (g) and two bolts (e) and clips
(f) from the dash shroud (b). See Figure 2-8.
(c)
(a)
(d)
(d)
(c)
(f)
(f)
(e)
(b)
(e)
(g)
Figure 2-8
2.
Mount the dash shroud (a) and align the
mounting holes. Using the bolts (c/e),
washers (d) and clips (f) install the dash
shroud (a) and snug the bolts (c) so that the
dash shroud (a) can be adjusted.
3.
Close the hood and align the dash shroud
(a) to the hood (g) leaving a uniform gap
between the hood (g) and the dash shroud (a).
4.
Raise the hood (g) and tighten the bolts (c/e)
that hold the dash shroud (a) on the dash (b).
Tire Pressure
WARNING! Equal tire pressure
should be maintained at all times.
Never exceed the maximum
inflation pressure shown on the
sidewall of the tire.
The recommended operating tire pressure is:
•
Approximately 10 psi for the rear tires
•
Approximately 14 psi for the front tires
IMPORTANT: Refer to the tire sidewall for exact
tire manufacturer's recommended or maximum
psi. Do not overinflate. Uneven tire pressure could
cause the cutting deck to mow unevenly.
Gas & Oil Fill-up
Oil
IMPORTANT: Your tractor is shipped with motor
oil in the engine. However, you MUST check the oil
level before operating. Be careful not to overfill.
Service and check the engine oil as instructed
(c)
in the Engine Operator's Manual. Read the
instructions carefully.
Gasoline
The gasoline tank is located under the hood. Do
not overfill.
WARNING! Use extreme care when
handling gasoline. Gasoline is
extremely flammable and the vapors
are explosive. Never fuel machine
indoors or while the engine is hot or
running. Extinguish cigarettes, cigars,
pipes, and other sources of ignition.
NOTE : Purchase gasoline in small quantities. Do not
use gasoline left over from the previous season, to
minimize gum deposits in the fuel system.
•
This engine is certified to operate on
unleaded gasoline. For best results, fill the
fuel tank with only clean, fresh, unleaded
gasoline with a pump sticker octane rating
of 87 or higher.
•
Gasohol (up to 10% ethyl alcohol, 90%
unleaded gasoline by volume) is an
approved fuel. Other gasoline/alcohol
blends, such as E85, are not approved.
•
Methyl Tertiary Butyl Ether (MTBE) and
unleaded gasoline blends (up to a maximum
of 15% MTBE by volume) are approved
fuels. Other gasoline/ether blends are not
approved.
•
Fill fuel tank outdoors or in well-ventilated
area.
•
Never remove gas cap or add fuel while the
engine is hot or running. Allow engine to
cool at least two minutes before refueling.
•
If gasoline is spilled, wipe it off the engine and
equipment. Move machine to another area.
Wait five minutes before starting the engine.
To Add Gasoline
Refer to Figure 2-1 and proceed to your applicable
model for your gas tank.
Hydrostatic Models
1.
Turn the engine OFF and let the engine cool
at least two minutes before removing the
fuel cap. The gasoline tank is located under
the hood. Remove the fuel cap by turning it
counter-clockwise.
2.
Fill the fuel tank with gasoline. Use only
clean, fresh (no more than 30 days old),
unleaded gasoline. Fill tank to the base
of the filler neck to allow space for fuel
expansion. DO NOT TOP OFF THE TANK
WITH FUEL. See Figure 2-9.
Figure 2-9
3.
Reinstall the fuel cap.
STOP! Continue to Setting the Deck
Gauge Wheels (If Equipped) on
STOP
page 9.
Foot Control CVT Models & CVT Models
1.
Turn the engine OFF and let engine cool
at least two minutes before removing the
fuel cap. The gasoline tank is located under
the hood. Remove the fuel cap by turning it
counter-clockwise.
2.
Fill the fuel tank with gasoline. Use only
clean, fresh (no more than 30 days old),
unleaded gasoline. Fill tank to no more
than 1⁄2" below bottom of filler neck to allow
space for fuel expansion. See Figure 2-10.
Figure 2-10
3.
Reinstall the fuel cap.
IMPORTANT: Do not overfill the tank. Fill
tank to no more than 1⁄2" below bottom of
S
2 — A
& S
ection
SSembly
-U
9
et
p
Hide quick links:
Advertisement
