Panasonic KX-FT982HK Operating Instructions Manual page 30

8. Programmable Features
Code #39: Changing the display contrast
LCD CONTRAST
=NORMAL [±]
"NORMAL" (default): For normal contrast.
"DARKER": Used when the display contrast is too light.
Code #41: Changing the fax activation code
FAX ACTIVATION
=ON [±]
If you wish to use an extension telephone (page 22) to
receive faxes, activate this feature and program the
activation code.
1. Press {MENU}.
2. Press {#}, then {4}{1}.
3. Press {A} or {B} repeatedly to select "ON".
4. Press {SET}.
5. Enter your code (2 to 4 digits) using the dial keys
{0}–{9}, {*} and {#}.
L The default code is ";;;9".
6. Press {SET}.
7. Press {MENU}.
Code #44: Setting the memory reception alert
RECEIVE ALERT
=ON [±]
To alert you with a beeping sound when a received fax
document is stored into memory due to some existing
problem.
The slow beeps will continue until you clear the printing
problem and make sure the unit is supplied with enough
paper to print the stored document.
"ON" (default): You will be alerted to a reception problem
by a beeping sound.
"OFF": Deactivates this feature.
Code #46: Setting friendly reception
FRIENDLY RCV
=ON [±]
To receive a fax automatically when you answer a call
and hear a fax calling tone (slow beep).
"ON" (default): You do not have to press {FAX/START}
for fax reception.
"OFF": You have to press {FAX/START} for fax
reception.
Code #49: Setting the auto disconnection
AUTO DISCONNECT
=ON [±]
To answer a call with an extension telephone in TEL/FAX
mode (page 22), activate this feature and program the
code.
1. Press {MENU}.
2. Press {#}, then {4}{9}.
30
3. Press {A} or {B} repeatedly to select "ON".
4. Press {SET}.
5. Enter your code 2 to 4 digits, using 0-9 and {*}.
L The default code is ";0".
6. Press {SET}.
7. Press {MENU}.
Code #58: Setting the scan contrast
SCAN CONTRAST
=NORMAL [±]
To send or copy a document with faint or dark writing, set
this feature before starting transmission or copying.
"NORMAL" (default): Used for normal writing.
"LIGHT": Used for dark writing.
"DARKER": Used for faint writing.
L This feature is not valid if you select "PHOTO"
resolution for sending (page 18) or copying (page 27)
a document.
Code #59: Setting the print contrast
PRINT CONTRAST
=NORMAL [±]
To adjust the darkness of received or copied documents.
"NORMAL" (default): Normal contrast.
"DARKER": Darker contrast.
Code #72: Setting recall/flash time
SET FLASH TIME
=400ms [±]
The recall/flash time depends on your telephone
exchange or host PBX. You can select "900ms",
"700ms", "600ms", "400ms" (default), "300ms",
"250ms", "200ms", "160ms", "110ms", "100ms",
"90ms" or "80ms".
Note:
L If the unit is connected via a PBX, this setting may
need to be changed in order for PBX functions
(transferring a call, etc.) to work correctly. Consult
your PBX supplier for the correct setting.
Code #73: Changing the receiving mode in the
manual answer setting
MANUAL ANSWER
=TEL [±]
"TEL" (default): Telephone mode (page 22)
"TEL/FAX": Telephone/Fax mode (page 22)
Code #76: Setting the connecting tone
CONNECTING TONE
=ON [±]
If you often have trouble when sending faxes, this feature
allows you to hear connecting tones: fax tone, ring back
tone and busy tone. You can use these tones to confirm
the status of the other party's machine.
"ON" (default): You will hear connecting tones.