Nominal Data; Technical Description; Mounting Data; Transport And Storage Conditions - ebm-papst M1G055-BD91-26 Operating Instructions Manual

M1G055-BD91-26

3.2 Nominal data

Motor M1G055-BD
Phase 1~
Nominal voltage / VAC 230
Frequency / Hz 50/60
Method of obtaining
ml
data
Speed (rpm) / min -1 1400
Power consumption / W
27
Power output / W 12
Current draw / A 0.24
Rated torque / Ncm 8
Min. ambient -30
temperature / °C
Max. ambient 50
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change

3.3 Technical description

Weight 0.9 kg
Motor size 55
Rotor surface Painted black
Electronics housing Die-cast aluminum
material
Direction of rotation Counterclockwise, viewed toward rotor
Degree of protection IP54
Insulation class
"B"
Moisture (F) / H1
Environmental (H)
protection class
Installation position Any
Condensation None
drainage holes
Mode S1
Motor bearing Ball bearing
Technical features - Speed setting input (230 V)
- ESM+ expandable with plug-in
module
- Soft start
- Thermal overload protection for motor
Speed levels 2
Touch current <= 0.25 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection Thermal overload protector (TOP)
internally connected
with cable Lateral
Protection class I (with customer connection of protective
earth)
Conformity with EN 60034-1; EN 60204-1; EN 60335-1;
standards EN 60335-2-24; EN 60335-2-80; EN
60335-2-89; CE
Approval CSA C22.2 No. 77; VDE; UL 1004-3;
EAC; CCC
Item no. 50356-5-9970 · ENU · Change 234164 · Approved 2021-08-11 · Page 5 / 10
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
1~
; Use the device in accordance with its degree of protection.
230
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
1000
accuracy.
The color pigments in the paints used perceptibly react to UV light over
-
the course of time. The product is to be protected against UV radiation to
prevent the formation of patches and fading. Changes in color are not a
reason for complaint and are not covered by the warranty. UV radiation
-30
in the frequency range and the intensity of natural solar radiation has no
effect on the technical properties of the products.
50

3.4 Mounting data

Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
Strength class of
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-

3.5 Transport and storage conditions

Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)

3.6 Electromagnetic compatibility

EMC immunity to
interference
EMC circuit feedback
EMC interference
emission
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
8.8
locking screws).
+ 80 °C
- 40 °C
According to EN 61000-6-2 (industrial
environment)
According to EN 61000-3-2/3
According to EN 61000-6-3 (household
environment)