Nominal Data; Technical Description; Mounting Data; Transport And Storage Conditions - ebm-papst M3G084-GF08-81 Operating Instructions Manual

M3G084-GF08-81

3.2 Nominal data

Motor M3G084-GF
Phase 1~
Nominal voltage / VAC 230
Nominal voltage 200 .. 277
range / VAC
Frequency / Hz
50/60
Method of obtaining ml
data
Status prelim.
Speed (rpm) / min -1 1500
Power consumption / W
392
Power output / W 314
Current draw / A 1.7
Rated torque / Ncm 200
Min. ambient -25
temperature / °C
Max. ambient 40
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change

3.3 Technical description

Weight 6.8 kg
Motor size 84
Electronics housing Die-cast aluminum
material
Housing material Die-cast aluminum
Direction of rotation Clockwise, viewed toward shaft
Degree of protection IP55
Insulation class
"B"
Moisture (F) / F3-1
Environmental (H)
protection class
Installation position Any
Cooling hole/opening On rotor side
Mode S1
Motor bearing Ball bearing
Technical features - Output 10 VDC, max. 10 mA
- Alarm relay
- Motor current limitation
- PFC, active
- Soft start
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from the mains
- Thermal overload protection for
electronics/motor
- Line undervoltage / phase failure
detection
Touch current
<= 3.5 mA
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Motor protection Thermal overload protector (TOP)
internally connected
Item no. 50840-5-9970 · ENU · Change 94899 · Approved 2018-03-06 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Protection class
Conformity with
standards
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.

3.4 Mounting data

Strength class of
screws
For screw clearance, see Chapter 3.1 Product drawing
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.

3.5 Transport and storage conditions

Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)

3.6 Electromagnetic compatibility

EMC immunity to
interference
EMC circuit feedback
EMC interference
emission
I (with customer connection of protective
earth)
EN 61800-5-1; CE
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
8.8
+80 °C
-40 °C
According to EN 61000-6-2 (industrial
environment)
According to EN 61000-3-2/3
According to EN 61000-6-4 (industrial
environment)