Table of Contents
Advertisement
M3G112-GA32-51
3.2 Nominal data
Motor
M3G112-GA
Phase
3~
Nominal voltage / VAC
400
Nominal voltage
380 .. 480
range / VAC
Frequency / Hz
50/60
Method of obtaining
ml
data
Status
prelim.
Speed (rpm) / min
-1
1500
Power consumption / W
915
Power output / W
785
Current draw / A
1.6
Rated torque / Ncm
500
Min. ambient
-25
temperature / °C
Max. ambient
40
temperature / °C
ml = Max. load · me = Max. efficiency · fa = Free air
cs = Customer specification · ce = Customer equipment
Subject to change
3.3 Technical description
Weight
9.8 kg
Motor size
112
Electronics housing
Die-cast aluminum
material
Housing material
Die-cast aluminum
Direction of rotation
Clockwise, viewed toward shaft
Degree of protection
IP55
Insulation class
"B"
Moisture (F) /
F3-1
Environmental (H)
protection class
Installation position
Any
Cooling hole/opening
On rotor side
Mode
S1
Motor bearing
Ball bearing
Technical features
- Output 10 VDC
- Output 20 VDC
- Output for slave 0-10 V
- Input for sensor 0-10 V or 4-20 mA
- Alarm relay
- Integrated PID controller
- Motor current limitation
- PFC, passive
- RS-485 ebmBUS
- Soft start
- Control input 0-10 VDC / PWM
- Control interface with SELV potential
safely disconnected from supply
- Thermal overload protection for
electronics/motor
- Line undervoltage / phase failure
detection
Item no. 50782-5-9970 · ENU · Change 94899 · Approved 2018-03-02 · Page 5 / 11
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
Operating instructions
Touch current
according to IEC
60990 (measuring
circuit Fig. 4, TN
system)
Electrical hookup
Motor protection
Protection class
Conformity with
standards
Approval
; Use the device in accordance with its degree of protection.
Information on surface quality
The surfaces of the products conform to the generally applicable industrial
standard. The surface quality may change during the production period.
This has no effect on strength, dimensional stability and dimensional
accuracy.
The color pigments in the paints used perceptibly react to UV light over
the course of time. This does not however in any way affect the
technical properties of the products. The product is to be protected against
UV radiation to prevent the formation of patches and fading. Changes in
color are not a reason for complaint and are not covered by the warranty.
3.4 Mounting data
Strength class of
screws
; Secure the screws against unintentional loosening (e.g. use self-
locking screws).
Any further mounting data required can be taken from the product
drawing or Section Chapter 4.1 Mechanical connection.
3.5 Transport and storage conditions
Max. permitted
ambient temp. for
motor (transport/
storage)
Min. permitted
ambient temp. for
motor (transport/
storage)
3.6 Electromagnetic compatibility
EMC immunity to
interference
EMC circuit feedback
EMC interference
emission
<= 3.5 mA
Terminal box
Thermal overload protector (TOP)
internally connected
I (with customer connection of protective
earth)
EN 61800-5-1; CE
EAC
With regard to cyclic speed loads, note that the rotating parts of
the device are designed for a maximum of one million load
cycles. If you have special questions, consult ebm-papst for
support.
8.8
+80 °C
-40 °C
According to EN 61000-6-2 (industrial
environment)
According to EN 61000-3-2/3
According to EN 61000-6-3 (household
environment)
Advertisement
Table of Contents
