Page 2
électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. MB-806A (CE) WRU-806A (CE, AU)
Page 6
English Table of Contents Precautions ............1 Channel Setting ..........8 WARNING Overview ............2 Automatic Search and Setting of Available To prevent fire or shock hazard, do not Channels ............9 Features ............. 2 expose the unit to rain or moisture. Operation ............
Page 7
UHF wireless This tuner is designed to enable simultaneous use of microphone system without causing intermodulation. The MB-806A can be mounted in an EIA standard 19- multiple channels when channels are selected It is therefore recommended that you usually use a Preprogrammed wireless channel plan for inch rack (1 U size).
Page 8
Location of Parts and Controls Front Panel Rear Panel 1 POWER switch 2 GP button 1 ANTENNA A, B IN/DC 9V OUT connectors 4 + button 2 ANTENNA A, B ATT switches 3 AC IN connector BATT – POWER OUTPUT LEVEL IN(DC 9V OUT) LINE...
Page 9
Always hold the WRU-806A by the side. • Do not touch the connectors on the rear panel of the ANTENNA B IN ANTENNA A IN Lever WRU-806A. MB-806A • Be careful of static electricity. Bottom Panel MIX OUTPUT TUNER OUTPUT AC IN...
Page 10
Power on the wireless microphones or transmitters always set the tuners to different channels within the When you use the MB-806A Base Unit in a multi- after adjusting them to the channels of each tuner same group (other than group 00).
Page 11
Operation Muting Functions This tuner has the following three muting functions, which work in combination. (1) Muting by RF input level As sufficient S/N for the audio output may not be obtained if no RF signal is received or the RF input level is low, the audio output can be muted when the Connect the output signals to a mixer or an RF input level falls below the muting level.
Page 12
862.000 MHz Operating temperature being received, the audio signal tuner’s tone squelch circuit. Contact your nearest Sony dealer. AU66 model: 792.250 to 0°C to 40°C output is muted. If you are using a WRT-810A (AU66) wireless microphone, a 805.500 MHz...
Page 13
Dieses Produkt wurde im Hinblick auf hervorragenden free operation in multi-channel systems. To maintain interferenzfreien Betrieb in Mehrkanalsystemen this, Sony recommends that one of the original Sony entwickelt. Deshalb empfehlen wir, eine der Sony- groups, number 01, 02, 03, 04, 13, L1, L2, M1 or M2 Kanalgruppen.
Page 14
User group No. of simultaneously CE62 model/Modell CE62 Modell Gruppe-Anzeige Frequenz-raster Benutzergruppe selectable channels Anzahl der Simultankanäle Sony Original Channel Groups/Sony Kanalgruppen CE62 125 kHz Sony original channel *(111) groups Group 13/Gruppe 13 GP/CH indication (example)/GP/CH-Anzeige Group 01/Gruppe 01 Sony Kanalgruppen 12-channel group/12-Kanal-Gruppe (Beispiel): 00.
Page 15
http://getMANUAL.com Wireless Channel Lists/Übertragungskanallisten German User Group-3/Deutschen Benutzergruppe-3 German User Group-4/ German User Groups/Deutschen Benutzergruppen Deutschen GP/CH indication (example)/GP/CH-Anzeige (Beispiel): 62A 04 GP/CH indication (example)/GP/CH-Anzeige (Beispiel): 62 080 Benutzergruppe-4 Group 62A/Gruppe 62A Group 63A/Gruppe 63A Group 62: 241-channel group (single-channel operation)/Gruppe 62: 241-Kanal-Gruppe (Einkanalbetrieb) GP/CH indication (example)/GP/ 7-channel group 10-channel group/10-Kanal-Gruppe...
Page 16
Wireless Channel Lists/Übertragungskanallisten GP/CH indication (example)/GP/CH-Anzeige (Beispiel): 63 001 WL Channel Frequency WL Channel Frequency WL-Kanal Frequenz (MHz) WL-Kanal Frequenz (MHz) 62-240 804.000 62-280 805.000 Group 63: 320-channel group (single-channel operation)/Gruppe 63: 320-Kanal-Gruppe (Einkanalbetrieb) 62-241 804.025 62-281 805.025 Frequency range: 806.025 to 814.000 MHz/Frequenzbereich: 806,025 bis 814,000 MHz 62-242 804.050 62-282...
Page 17
Frequency WL Channel Frequency CE69 Model/Modell CE69 WL-Kanal Frequenz WL-Kanal Frequenz WL-Kanal Frequenz WL-Kanal Frequenz (MHz) (MHz) (MHz) (MHz) Sony Original Channel Groups Group 01/Gruppe 01 63-161 810.025 63-201 811.025 63-241 812.025 63-281 813.025 63-162 810.050 63-202 811.050 63-242 812.050 63-282 813.050...
Page 18
Use when TV channel 67 is on the air. WL Channel Frequency (MHz) WL Channel Frequency (MHz) Group 11: 12-channel group Sony Original Channel Groups 66-02 792.375 66-31 796.000 Use when TV channels both 66 and 67 are available. 66-04 792.625...
Page 19
Notes System Configuration • Be sure to power off the MB-806A before installing this unit. • The buttons and display of this unit may be damaged if they are The unit can be used with a UHF Synthesized Wireless Microphone or gripped too strongly.
Page 20
Specifications Tuner Reception type Circuit system Dual conversion superheterodyne Reception frequencies CE62 model: 800.000 to 814.000 MHz CE69 model: 854.125 to 862.000 MHz Local oscillators Crystal controlled PLL synthesizer 60 dB or more (at ±250 kHz detuned) Selectivity Spurious rejection ratio 70 dB or more Image rejection ratio 60 dB or more...
Page 21
Notes Phase Locked Loop (PLL) synthesized system • Be sure to power off the MB-806A before installing this unit. The unit has a refined phase locked loop (PLL) synthesizer circuit and • The buttons and display of this unit may be damaged if they are covers two UHF TV channels.
(Tuner Unit) 2-2. Precaution in Wiring Harness . The harness inside the MB-806A are laid out so that they are not positioned close to the heat-producing parts or high voltage present parts by routing the harnesses properly or using purse locks.
2-3. Error Messages The following error messages will appear if an error is detected by the built-in self diagnostics function of the MB-806A with WRU-806A. Error Massage Comments Countermeasure Err 01 Error the backup memory Because data is initialized, perform the group setting, channel setting again.
. If there is a fault, WRU-806A (repair unit) is defective. Check the WRU-806A then fix a faulty section, and perform “3. Electrical Alignment”. . If there is no fault found on the MB-806A, repairing WRU-806A is no longer defective. Thus the repairing MB- 806A, other than WRU-806A, is defective.
(SSG) so that the = _113 dBm 0 dBuV 50 Z meter reads 50 mV. (EMF = Electromotive force) 50 Z 50 mV 0 dBm = 1 mW at 50 Z loaded MB-806A (CE) WRU-806A (CE, AU)
Page 29
The adjustment procedures describe that the WRU-806A (to be adjusted) is installed into the Tuner [1]slot on the 2. Remove the tuner unit (WRU-806A) to be adjusted from the MB-806A. Refer to “ Section 1. Operating MB-806A. Instructions ” for removal.
Page 30
(A C3 L) LCD: (12)Set the FREQUENCY (carrier frequency) of the signal B C3 L generator as follow. FREQUENCY(carrier frequency): (B C3 L) CE62 model; 811.000 MHz CE69 model; 861.000 MHz AU66 model; 804.000 MHz MB-806A (CE) WRU-806A (CE, AU)
Page 31
(24)Indication on the LCD (Tuner [1]) appears as follows: 2. Remove the tuner unit (WRU-806A) to be adjusted LCD: from the MB-806A. Refer to “ Section 1. Operating Instructions ” for removal. . CE62 model 3. Remove the upper side case lid of the tuner unit...
Page 32
“Step 2. Tuner [1] (Tuner unit 1) adjustment” on the CE69 model; Group 00, 6933 channel (858.125 MHz) AU66 model; Group00, 6701 channel (799.250 MHz) respective tuner units that are installed in the MB-806A. Muting: OFF When performing the above described adjustments change Rear panel the following details as shown below of the “Step 2.
Page 33
(Lower side) (Upper side) RV205 Oscilloscope 5. Attach the lower side case lid to the tuner unit, and insert the tuner unit to the slot of the MB-806A. DC range setting Tuner unit (Upper side) Connection Same as “ 2. Output level adjustment ”.
(6) of “ Step 1: Tuner [1] (Tuner unit 1) adjustment” on 7. Muting level/RF indicator check ↓ the respective tuner unit that are installed in the MB-806A. When performing the above described adjustment change 8. BATT indicator check ↓...
Page 35
806A, perform the adjustments from procedures (1) to (11) of “Step 1. Tuner [1] (Tuner unit 1) checking” on the (1) Set the MB-806A as follows; respective tuner units that are installed in the MB-806A. Front panel (Tuner [1]) When performing the above described checking change the FREQUENCY(carrier frequency): following details as shown below, of the “Step 1.
Page 36
(No modulation). (7) Check that output level of the TUNER OUTPUT 1 is respective tuner units that are installed in the MB-806A. _62 dB or less (S/N is 62 dB or more with A-weighted When performing the above described checking change the filter) as compared with the level of procedure (4) following details as shown below, of the “Step 1.
Page 37
The checking procedures describe that the WRU-806A (to be When performing the above described checking change the adjusted) is installed into the Tuner [1] slot on the MB-806A. following details as shown below, of the “Step 1. Tuner [1] (Tuner unit 1) checking”.
Page 38
“Step 1. Tuner [1] (Tuner unit 1) checking” on the AU66 model; 799.250 MHz RF OUTPUT (Output level): 60 dBuV respective tuner units that are installed in the MB-806A. (= _53 dBm) When performing the above described checking change the MODULATION (Modulation frequency): 1 kHz following details as shown below, of the “Step 1.
Page 39
806A, perform the adjustments from procedures (1) to (6) of “Step 1. Tuner [1] (Tuner unit 1) checking” on the LCD: respective tuner units that are installed in the MB-806A. When performing the above described checking change the ± 5 dB...
Page 40
806A, perform the adjustments from procedures (1) to (4) of “Step 1. Tuner [1] (Tuner unit 1) checking” on the respective tuner units that are installed in the MB-806A. The checking procedures describe that the WRU-806A(to When performing the above described checking change the be adjusted) is installed into the Tuner [1] slot on the MB- following details as shown below, of the “Step 1.
Page 41
(4) Check that RF Indicator LED lights (green) and “NO TONE” message appears on LCD (Tuner [1]). respective tuner units that are installed in the MB-806A. (5) Change the RF OUTPUT (output level) of the signal When performing the above described checking change the generator as shown below.
Page 42
“Step 1. Tuner [1] (Tuner unit 1) checking” on the (= _53 dBm) MODULATION (Modulation frequency): respective tuner units that are installed in the MB-806A. 32.782 kHz When performing the above described checking change the (32.782 kHz must be set following details as shown below, of the “Step 1.
Page 43
806A, perform the adjustments from procedures (1) to (5) of “Step 1. Tuner [1] (Tuner unit 1) checking” on the respective tuner units that are installed in the MB-806A. The checking procedures describe that the WRU-806A (to When performing the above described checking change the be adjusted) is installed into the Tuner [1] slot on the MB- following details as shown below, of the “Step 1.
Page 48
C OB C OB C OB C OB C OB C OB GAIN CELL GAIN CELL LATCH GAIN CELL SOUT C OB C OB C OB C OB C OB C OB C OB C OB MB-806A (CE) WRU-806A (CE, AU)
Page 49
0 : LOW LEVEL 1 : HIGH LEVEL TC74HC4053AFT(EL) (TOSHIBA) C-MOS TRIPLE 2-CHANNEL ANALOG MULTIPLEXER/DEMULTIPLEXER —TOP VIEW— OPEN OPEN OPEN CONTROL INPUTS SELECT ON CHANNEL : LOW LEVEL : HIGH LEVEL OPEN : DON’T CARE MB-806A (CE) WRU-806A (CE, AU)
Page 50
Judgment for model type IF-DO Serial I/O control (L: WRR-802A, H: MB-806A) TEST Test mode (L: ON) ADDRESS Judgment for slot number (MB-806A) MASTER/SLAVE MASTER/SLAVE communication DIST1 Selection 1 for destination (model type) DIST2 Selection 2 for destination (model type)
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. Parts list has the present standardized repair parts.
2-545-216-01 o INSULATING SHEET (B) 2-545-338-01 o SPRING (F) 2-545-387-11 s +BTT M3 (S TITE) 2-545-413-01 o SIELD (R) 2-545-750-01 o LID (BLIND) 4-942-568-41 s EMBLEM (N0.5), SONY 9-911-844-99 s SHEET, SPONGE Accessory 1-501-952-11 s ANTENNA Screws/Washers 7-682-246-09 s SCREW +K 3X5 (EP-FE/ZNBK/CM2)
Page 53
B 3x5 B 3x5 B 3x5 B 3x3 B 3x8 BVTT 3x6 BVTT 3x6 K 3x5 K 3x5 BVTT 3x6 K 3x5 K 3x5 BVTT 3x6 K 3x5 BVTT K 3x5 BVTT 2x4 WRU-806A (Tuner unit) MB-806A (CE) WRU-806A (CE, AU)
5-3. Electrical Parts List 5-3-1. MB-806A --------------------- ------------------------- CANON (CN-1908) BOARD CONNECTOR (CN-1907) BOARD --------------------- ------------------------- Ref. No. Ref. No. or Q'ty Part No. SP Description or Q'ty Part No. SP Description 1-674-362-11 o PRINTED WIRING BOARD, CN-1908 A-8323-049-A o CONNECTOR MOUNTED PC BOARD (A)
Page 55
1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V C1512 1-164-156-11 s CAPACITOR,CERAMIC 0.1MF/25V F C1218 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V C1513 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V C1219 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V C1514 1-163-038-91 s CAPACITOR, CERAMIC 0.1MF/25V MB-806A (CE) WRU-806A (CE, AU)
Page 56
1-162-907-11 s CAPACITOR,CERAMIC 2PF/50V(CK) C1818 1-162-964-11 s CAPACITOR,CERAMIC 1000PF/50V B C1956 1-162-907-11 s CAPACITOR,CERAMIC 2PF/50V(CK) C1820 1-162-964-11 s CAPACITOR,CERAMIC 1000PF/50V B C1957 1-162-907-11 s CAPACITOR,CERAMIC 2PF/50V(CK) C1822 1-162-964-11 s CAPACITOR,CERAMIC 1000PF/50V B C1958 1-162-907-11 s CAPACITOR,CERAMIC 2PF/50V(CK) MB-806A (CE) WRU-806A (CE, AU)
Page 57
8-759-700-94 s IC NJM5532M L1961 1-414-461-31 s INDUCTOR, CHIP (K) 6.8NH IC1304 8-759-524-11 s IC TC4066BF(EL,N) L1962 1-414-461-31 s INDUCTOR, CHIP (K) 6.8NH IC1305 8-759-524-11 s IC TC4066BF(EL,N) L1963 1-414-461-31 s INDUCTOR, CHIP (K) 6.8NH MB-806A (CE) WRU-806A (CE, AU)
Page 58
1-218-718-11 s RESISTOR CHIP 12K 1/16W (1608) R1213 1-218-709-11 s RESISTOR,METAL 5.1K 1/16W R1009 1-218-718-11 s RESISTOR CHIP 12K 1/16W (1608) R1214 1-208-799-11 s RESISTOR,CHIP 5.1K 1/10W(2125) R1010 1-208-808-11 s RESISTOR,CHIP 12K 1/10W (2012) R1215 1-216-809-11 s RESISTOR,CHIP 100 1/16W 1608 MB-806A (CE) WRU-806A (CE, AU)
Page 59
1-216-835-11 s RESISTOR,CHIP 15K 1/16W R1627 1-216-833-11 s RESISTOR,CHIP 10K 1/16W 1608 R1423 1-216-826-11 s RESISTOR,CHIP 2.7K 1/16(1608) R1629 1-218-285-11 s RESISTOR,CHIP 75 1/16W (1608) R1429 1-218-285-11 s RESISTOR,CHIP 75 1/16W (1608) R1631 1-216-864-11 s RESISTOR,CHIP 0 1/16W (1608) MB-806A (CE) WRU-806A (CE, AU)
Page 60
1-216-797-11 s RESISTOR,CHIP 10 1/16W 1608 R1867 1-216-845-11 s RESISTOR,CHIP 100K 1/16W(1608) R1868 1-216-822-11 s RESISTOR, CHIP 1.2K 1/16W 1608 R1871 1-216-812-11 s RESISTOR,CHIP 180 1/16 1608 R1872 1-216-797-11 s RESISTOR,CHIP 10 1/16W 1608 5-10 MB-806A (CE) WRU-806A (CE, AU)
2-545-811-01 o LABEL, 5 COLOR (FOR CE62,CE69 MODEL) Ref. No. 3-867-236-21 s MANUAL, INSTRUCTION or Q'ty Part No. SP Description (FOR CE62,CE69 MODEL) 3-867-236-31 s MANUAL, INSTRUCTION 1-790-794-11 s WIRE, FLAT TYPE (35 CORE) (FOR AU66 MODEL) 5-17 MB-806A (CE) WRU-806A (CE, AU)
Page 69
MB-871 board MB-806A Tuner Base Unit CN-1907 board T1801 J1812 J1906 S1803 J1702 Q1801 T1803 MB-806A is composed of power supply block, audio block, J1811 J1905 ANTENNA B IN T1805 J1810 J1904 DISTRI- CN116 and following boards. / DC 9V OUT...
Page 70
Tuner Unit Block Diagram The audio output signal from the diversity switching circuit WRU-806A is passed through the muting circuit, de-emphasis circuit, low pass filter circuit and expander circuit then amplified by the AF amplifier. MB-806A (CE) WRU-806A (CE, AU)
Page 76
• DC Voltage are taken with digital multimeter (input impedance 1 MΩ or more) under no-signal conditions. • AF level value of AF out (2), (3), (4), (5), (6) blocks are same as AF out (1) block. MB-806A (CE) WRU-806A (CE, AU)
Page 77
C1887 (TPL3) (TPL3) ATT SW A COM R1880 C1888 R1879 220k 220k BOARD NO. 1-674-362-11 R1803 CN-1908 BOARD C1621 S1802 R1804 C1814 100p S1801 ATT SW B COM IC1605 TC4066BF(E R1851 S1803 R1852 MB-806A (CE) C1871 100p WRU-806A (CE, AU)