TP-Link TL-SG1218MPE User Manual
  1. Manuals
  2. Brands
  3. TP-Link Manuals
  4. Switch
  5. TL-SG1218MPE
  6. User manual

TP-Link TL-SG1218MPE User Manual

Easy smart switch
Hide thumbs Also See for TL-SG1218MPE:
Table of Contents

Advertisement

Quick Links

User Guide
Easy Smart Switch
TL-SG108PE/TL-SG1016DE/TL-SG1016PE/TL-SG1024DE/TL-SG1218MPE
1910012537 REV3.3.1
March 2019

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TL-SG1218MPE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for TP-Link TL-SG1218MPE

Summary of Contents for TP-Link TL-SG1218MPE

  • Page 1 User Guide Easy Smart Switch TL-SG108PE/TL-SG1016DE/TL-SG1016PE/TL-SG1024DE/TL-SG1218MPE 1910012537 REV3.3.1 March 2019...

  • Page 2: Table Of Contents

    CONTENTS About This Guide Intended Readers ................................1 Conventions ................................... 1 More Information ................................. 1 Introduction Product Overview ................................4 Logging Into the Switch ..............................5 Managing System System ..................................... 8 Overview .........................................8 Supported Features ....................................8 Configuring System Info ..............................9 Viewing the System Information ...............................9 Specifying the Device Description ..............................9 Configuring IP ..................................
  • Page 3 Example for Configuring IGMP Snooping ..........................30 Network Requirements ................................30 Configuration Scheme ................................30 Configuration Steps ................................31 Example for Configuring LAG ................................32 Network Requirements ................................32 Configuration Steps ................................33 Appendix: Default Parameters ............................. 34 Monitoring Monitoring ................................... 36 Overview ........................................36 Supported Features ....................................36 Viewing Port Statistics ..............................
  • Page 4 Configuring Basic QoS ..............................62 Configuring QoS in Port Based Mode ............................63 Configuring QoS in 802.1P Based Mode ..........................64 Configuring QoS in DSCP/802.1P Based Mode ........................64 Configuring Bandwidth Control ........................... 65 Configuring Storm Control ............................67 Configuration Example for Basic QoS........................69 Network Requirements ..................................69 Configuration Scheme ..................................69 Configuration Steps ....................................70...

  • Page 5: About This Guide

    You can also configure the switch using the Easy Smart Configuration Utility. For more information, refer to the Easy Smart Configuration Utility User Guide. Go to the website https://www.tp-link.com/support, search the model number of your switch, and you can find this guide on the product Support web page.
  • Page 6  The Installation Guide (IG) can be found where you find this guide or inside the package of the switch.  Specifications can be found on the product page at https://www.tp-link.com.  To ask questions, find answers, and communicate with TP-Link users or engineers, please visit to join TP-Link Community.
  • Page 7 Part 1 Introduction CHAPTERS 1. Product Overview 2. Logging Into the Switch...

  • Page 8: Product Overview

     PoE: PoE (Power over Ethernet) is a remote power supply function. With this function, the switch can supply power to the connected devices over twisted-pair cables. Note： Only TL-SG1016PE/TL-SG1218MPE supports the PoE configuration. User Guide...

  • Page 9: Logging Into The Switch

    Introduction Logging Into the Switch Logging Into the Switch To configure your switch through a web browser on your PC, follow these steps: 1) Connect your switch to the network and connect your PC to the switch. 2) Find out the IP address of the switch.  By default, the switch receives an IP address from a DHCP server (or a router that functions as a DHCP server) in your network.
  • Page 10 Introduction Logging Into the Switch Figure 2-2 Logging Into the Switch 7) The typical web interface displays below. You can view the running status of the switch and configure the switch on this interface. Figure 2-3 Launching the Web Interface User Guide...

  • Page 11: Managing System

    Part 2 Managing System CHAPTERS 1. System 2. Configuring System Info 3. Configuring IP 4. Configuring User Account 5. Backing up and Restoring the Switch 6. Rebooting the Switch 7. Resetting the Switch 8. Upgrading the Firmware 9. Appendix: Default Parameters...

  • Page 12: System

    System Reset is used to reset the switch to the factory default setting. All the settings will be cleared after the switch is reset. Firmware Upgrade To upgrade the firmware is to get more functions and better performance. Go to the website to download the updated firmware. https://www.tp-link.com User Guide...

  • Page 13: Configuring System Info

    Managing System Configuring System Info Configuring System Info With system information configuration, you can:  View the system information  Specify the device description 2.1 Viewing the System Information Choose the menu System > System Info to load the following page. You can view the basic system information of the switch.

  • Page 14: Configuring Ip

    Managing System Configuring IP Configuring IP You can configure the system IP address in the following two ways:  Configure the System IP Address Using DHCP  Configure the System IP Address Manually Configuring the System IP Address Using DHCP Choose the menu System >...
  • Page 15 Managing System Configuring IP Subnet Mask Specify the subnet mask of the switch.. Default Gateway Specify the default gateway of the switch. 3) Click Apply. User Guide...

  • Page 16: Configuring User Account

    Managing System Configuring User Account Configuring User Account With user account management, you can modify the administrator’s username and password in order to refuse illegal users. Choose the menu System > User Account to load the following page. Figure 4-1 Configuring User Account Follow these steps to configure the user account: 1) Specify the new username, enter the old password, specify a new password and confirm the new password.

  • Page 17: Backing Up And Restoring The Switch

    Managing System Backing up and Restoring the Switch Backing up and Restoring the Switch With backup and restore, you can:  Save the current configuration.  Restore to the previous configuration. Saving the Current Configuration Choose the menu System > System Tools > Backup and Restore to load the following page.

  • Page 18: Restoring To The Previous Configuration

    Managing System Backing up and Restoring the Switch Restoring to the Previous Configuration Choose the menu System > System Tools > Backup and Restore to load the following page. Figure 5-2 Restoring the Configuration Follow these steps to restore the switch to the previous configuration: 1) In the Config Restore section, click Browse to load the following page.
  • Page 19 Managing System Backing up and Restoring the Switch 2) Click Open and the following page will be displayed. In the Config Restore section, click Restore Config to restore the switch to the previous configuration. It will take effect after the switch automatically reboots. Figure 5-4 Restoring to the Previous Configuration Note: It will take several minutes to restore the configuration.

  • Page 20: Rebooting The Switch

    Managing System Rebooting the Switch Rebooting the Switch Choose the menu System > System Tools > System Reboot to load the following page. Click Reboot. Figure 6-1 Rebooting the Switch Note: It will take several minutes to reboot the switch. Wait without any operation while the switch •...

  • Page 21: Resetting The Switch

    Managing System Resetting the Switch Resetting the Switch Choose the menu System > System Tools > System Reset to load the following page. Figure 7-1 Resetting the Switch Follow these steps to reset the switch. 1) Click Reset, and the following page will pop up. Figure 7-2 Being Sure to Reset the Switch 2) Click OK to reset the switch.

  • Page 22: Upgrading The Firmware

    Managing System Upgrading the Firmware Upgrading the Firmware Choose the menu System > System Tools > Firmware Upgrade to load the following page. Figure 8-1 Being Ready to Upgrade the Firmware User Guide...
  • Page 23 Managing System Upgrading the Firmware Follow these steps to upgrade the firmware: 1) Click Choose File to load the following page. Specify the firmware file path and select the firmware to upgrade. Figure 8-2 Browsing the Firmware File 2) Click Open and the following page will be displayed. Click Upgrade. Figure 8-3 Upgrading the Firmware User Guide...
  • Page 24 Managing System Upgrading the Firmware Note: It will take several minutes to upgrade the firmware. Wait without any operation. • Select the proper software version matching with the hardware to upgrade. • To avoid damage, do not power down the switch while upgrading the firmware. •...

  • Page 25: Appendix: Default Parameters

    Managing System Appendix: Default Parameters Appendix: Default Parameters Default settings of System Info are listed in the following table. Table 9-1 Default Settings of System Info Parameter Default Setting Device Description The model name of the switch. Default settings of IP Setting are listed in the following table. Table 9-2 Default Settings of IP Address Configuration Parameter...

  • Page 26: Switching

    Part 3 Switching CHAPTERS 1. Switching 2. Configuring Ports 3. Configuring IGMP Snooping 4. Configuring LAG 5. Configuration Examples 6. Appendix: Default Parameters...

  • Page 27: Switching

    Switching Switching Switching Overview With the switching feature, you can configure port setting, IGMP Snooping and LAG. Supported Features The switch supports the following features about switching: Port Setting You can configure port status, speed, duplex mode and flow control for ports. IGMP Snooping In a point-to-multipoint network, packets can be sent in three ways: unicast, broadcast and multicast.
  • Page 28 Switching Switching a known multicast group will be transmitted to the designated receivers instead of being broadcast in the Layer2 network. The following figure shows how IGMP snooping works. Figure 1-1 IGMP Snooping Multicast packets transmission with Multicast packets transmission without IGMP Snooping IGMP Snooping Multicast router Multicast router...

  • Page 29: Configuring Ports

    Switching Configuring Ports Configuring Ports Choose the menu Switching > Port Setting to load the following page. Figure 2-1 Configuring Ports Follow these steps to configure the port parameters. 1) Select the desired ports and set basic parameters for the ports. Status Enable or disable the port.
  • Page 30 Switching Configuring Ports Flow Control Select On or Off to enable or disable the Flow Control feature. When Flow Control is enabled, when the switch gets overloaded, it will send a PAUSE frame to notify the peer device to stop sending data for a specific period of time, thus avoiding the packet loss caused by congestion.

  • Page 31: Configuring Igmp Snooping

    Switching Configuring IGMP Snooping Configuring IGMP Snooping Choose the menu Switching > IGMP Snooping to load the following page. Figure 3-1 Configuring IGMP Snooping Follow these steps to configure IGMP Snooping. 1) Enable IGMP Snooping. Enable or disable report message suppression according to your needs.

  • Page 32: Configuring Lag

    Switching Configuring LAG Configuring LAG Choose the menu Switching > LAG to load the following page. Figure 4-1 Configuring LAG Follow these steps to configure LAG: 1) Select the desired LAG group from the drop-down list. 2) Click the ports to add to the LAG group. Click Apply. 3) In the table below, you can verify the LAG configuration result.
  • Page 33 Switching Configuring LAG Note: It is recommended to configure the LAG function before configuring the other functions • for the member ports. Ensure that devices on both ends of the aggregation link use the same number of physical • ports with the same speed and duplex mode, flow control setting and QoS setting. Mirroring and mirrored port cannot be added to an LAG group.

  • Page 34: Configuration Examples

    Switching Configuration Examples Configuration Examples Example for Configuring IGMP Snooping 5.1.1 Network Requirements Host B, Host C and Host D are in the same VLAN of the switch. All of them want to receive multicast streams sent to the same multicast group. As shown in the following topology, Host B, Host C and Host D are connected to port 1, port 2 and port 3 respectively.

  • Page 35: Configuration Steps

    Switching Configuration Examples Demonstrated with TL-SG1016PE, the following section provides configuration steps. 5.1.3 Configuration Steps 1) Choose the menu VLAN > 802.1Q VLAN to load the following page. Select the 802.1Q VLAN Configuration as Enable. Click Apply. Specify the VLAN ID as 2. Specify the VLAN name as VLAN2.

  • Page 36: Example For Configuring Lag

    Switching Configuration Examples 2) Choose the menu VLAN > 802.1Q PVID Setting to load the following page. Select port 1, port 2, port 3 and port 4, and specify the PVID as 2 for the ports. Click Apply. Figure 5-3 Configuring 802.1Q PVID 3) Choose the menu Switching >...

  • Page 37: Configuration Steps

    Switching Configuration Examples Figure 5-5 Network Topology for LAG Port 1 Port 1 Port 2 Port 2 Port 3 Port 3 Switch A Switch B Hosts Servers Demonstrated with TL-SG105E, the following section provides configuration steps. The configuration steps are similar for both switches, here we take Switch A for example. 5.2.2 Configuration Steps Choose the menu Switching >...

  • Page 38: Appendix: Default Parameters

    Switching Appendix: Default Parameters Appendix: Default Parameters Default settings of Port are listed in the following table. Table 6-1 Default Settings of Port Configuration Parameter Default Setting Status Enabled Speed/Duplex Auto Flow Control Default settings of IGMP Snooping are listed in the following table. Table 6-2 Default Settings of IGMP Snooping Configuration Parameter...

  • Page 39: Monitoring

    Part 4 Monitoring CHAPTERS 1. Monitoring 2. Viewing Port Statistics 3. Configuring Port Mirror 4. Testing Cables 5. Configuring Loop Prevention 6. Appendix: Default Parameters...

  • Page 40: Monitoring

    Monitoring Monitoring Monitoring Overview With the monitoring feature, you can monitor the traffic on the switch. Supported Features Port Statistics Port Statistics is used to display the information of each port, which facilitates you to monitor the traffic and locate faults promptly. Port Mirror Port Mirror is used to monitor network traffic by forwarding copies of incoming and outgoing packets from one or multiple ports (mirrored ports) to a specified port (mirroring...

  • Page 41: Viewing Port Statistics

    Monitoring Viewing Port Statistics Viewing Port Statistics Choose the menu Monitoring > Port Statistics to load the following page. Figure 2-1 Viewing Port Statistics You can view the statistics of each port. You can click Clear to clear the data, also you can click Refresh to refresh the data.
  • Page 42 Monitoring Viewing Port Statistics Note: The frames with more than 1518 bytes, less than 64 bytes or with bad FCS (Frame Check • Sequence) are recorded as BadPkts. Because of the supporting feature of jumbo frame, the frames with more than 1518 bytes and •...

  • Page 43: Configuring Port Mirror

    Monitoring Configuring Port Mirror Configuring Port Mirror Choose the menu Monitoring > Port Mirror to load the following page. Figure 3-1 Configuring Port Mirror Follow these steps to configure port mirror: 1) Enable the port mirror feature globally. Specify a mirroring port. Click Apply. Port Mirror Enable or disable the port mirror feature globally.
  • Page 44 Monitoring Configuring Port Mirror Mirroring Port Select a port as the mirroring port. Traffic passing through the mirrored ports will be mirrored to the mirroring port. 2) Select one or more mirrored ports, enable or disable the ingress packets and egress packets to be mirrored for the ports.

  • Page 45: Testing Cables

    Monitoring Testing Cables Testing Cables Choose the menu Monitoring > Cable Test to load the following page. Figure 4-1 Testing Cables Follow these steps to diagnose the cable: 1) Select your desired ports for test. Click Apply to test cables connected to the selected ports.
  • Page 46 Monitoring Testing Cables Cable Fault Displays the length from the port to the trouble spot, if the connection Distance (m) status is short, close (or short) or crosstalk. User Guide...

  • Page 47: Configuring Loop Prevention

    Monitoring Configuring Loop Prevention Configuring Loop Prevention Choose the menu Monitoring > Loop Prevention to load the following page. Figure 5-1 Configuring Loop Prevention Follow these steps to configure loop prevention: 1) Enable or disable loop prevention. Loop Prevention Enable or disable the loop prevention feature globally. 2) Click Apply.

  • Page 48: Appendix: Default Parameters

    Monitoring Appendix: Default Parameters Appendix: Default Parameters Default settings of Port Mirror are listed in the following table. Table 6-1 Default Settings of Port Mirrror Configuration Parameter Default Setting Port Mirror Disable Default settings of Loop Prevention are listed in the following table. Table 6-2 Default Settings of Loop Preventikon Configuration Parameter...

  • Page 49: Configuring Vlan

    Part 5 Configuring VLAN CHAPTERS 1. Overview 2. Configuring MTU VLAN 3. Configuring Port Based VLAN 4. Configuring 802.1Q VLAN 5. Configuration Example for 802.1Q VLAN 6. Appendix: Default Parameters...

  • Page 50: Overview

    Configuring VLAN Overview Overview VLAN (Virtual Local Area Network) is a network technique that solves broadcasting issues in local area networks. It is usually applied in the following occasions:  To restrict broadcast domain: VLAN technique divides a big local area network into several VLANs, and all VLAN traffic remains within its VLAN.
  • Page 51 Configuring VLAN Overview Note: The switch works in one and only one VLAN mode at any time. When a specific VLAN mode is enabled, the other two VLAN modes will be disabled automatically and the corresponding VLAN configuration will be lost. User Guide...

  • Page 52: Configuring Mtu Vlan

    Configuring VLAN Configuring MTU VLAN Configuring MTU VLAN Choose the menu VLAN > MTU VLAN to load the following page. Figure 2-1 Configuring MTU VLAN Follow these steps to configure MTU VLAN: 1) Select MTU VLAN configuration as Enable. Click Apply. MTU VLAN Enable or disable the MTU VLAN mode.

  • Page 53: Configuring Port Based Vlan

    Configuring VLAN Configuring Port Based VLAN Configuring Port Based VLAN Choose the menu VLAN > Port Based VLAN to load the following page. Figure 3-1 Configuring Port Based VLAN Follow these step to configure port based VLAN: 1) Select the port based VLAN configuration as Enable. Click Apply. Port Based Enable or disable the port based VLAN mode.

  • Page 54: Configuring 802.1Q Vlan

    Configuring VLAN Configuring 802.1Q VLAN Configuring 802.1Q VLAN To complete the 802.1Q configuration, follow these steps: 1) Configure the VLAN, including creating a VLAN and adding the ports to the VLAN. 2) Configure the PVID. Configuring the VLAN Choose the menu VLAN > 802.1Q VLAN to load the following page. Figure 4-1 Configuring 802.1Q VLAN Follow these steps to configure the VLAN: 1) Select the 802.1Q VLAN Configuration as Enable.
  • Page 55 Configuring VLAN Configuring 802.1Q VLAN 802.1Q VLAN Enable or disable the 802.1Q VLAN mode. Configuration 2) Enter a VLAN ID and a VLAN name for identification. Select the untagged port(s) and the tagged port(s) respectively to add to the created VLAN based on the network topology. Click Add/Modify.

  • Page 56: Configuring The Pvid

    Configuring VLAN Configuring 802.1Q VLAN Configuring the PVID Choose the menu VLAN > 802.1Q PVID Setting to load the following page. Figure 4-2 Configuring 802.1Q PVID Follow these steps to configure the PVID: 1) Select the ports and set the PVID for the ports. PVID Set the PVID for the ports.

  • Page 57: Configuration Example For 802.1Q Vlan

    Configuring VLAN Configuration Example for 802.1Q VLAN Configuration Example for 802.1Q VLAN Network Requirements  Offices of Department A and Department B in the company are located in different places, and some computers in different offices are connected to the same switch.  It is required that computers can communicate with each other in the same department but not with computers in the other department.

  • Page 58: Network Topology

    Configuring VLAN Configuration Example for 802.1Q VLAN Network Topology The figure below shows the network topology. Host A1 and Host A2 are in Department A, while Host B1 and Host B2 are in Department B. Switch A and Switch B are located in two different places.

  • Page 59: Configuration Steps

    Configuring VLAN Configuration Example for 802.1Q VLAN Configuration Steps Demonstrated with TL-SG1016PE, the following section provides configuration steps. The configuration steps on both switches are similar, here we take Switch A for example. 1) Choose the menu VLAN > 802.1Q VLAN to load the following page. Select 802.1Q VLAN configuration as Enable.
  • Page 60 Configuring VLAN Configuration Example for 802.1Q VLAN 2) Choose the menu VLAN > 802.1Q VLAN to load the following page. Specify the VLAN ID as 2, specify the VLAN name as Dept_A. Add port 2 to the VLAN as an untagged port. Add port 4 to the VLAN as a tagged port.
  • Page 61 Configuring VLAN Configuration Example for 802.1Q VLAN 3) Choose the menu VLAN > 802.1Q VLAN to load the following page. Specify the VLAN ID as 3, specify the VLAN name as Dept_B. Add port 3 to the VLAN as an untagged port. Add port 4 to the VLAN as a tagged port.
  • Page 62 Configuring VLAN Configuration Example for 802.1Q VLAN Figure 5-5 Configuring 802.1Q PVID User Guide...

  • Page 63: Appendix: Default Parameters

    Configuring VLAN Appendix: Default Parameters Appendix: Default Parameters Default settings of VLAN are listed in the following tables. Table 6-1 Default Settings of MTU VLAN Configuration Parameter Default Setting MTU VLAN Configuration Disable Table 6-2 Default Settings of Port Based VLAN Configuration Parameter Default Setting Port Based VLAN Configuration...

  • Page 64: Configuring Qos

    Part 6 Configuring QoS CHAPTERS 1. QoS 2. Configuring Basic QoS 3. Configuring Bandwidth Control 4. Configuring Storm Control 5. Configuration Example for Basic QoS 6. Appendix: Default Parameters...

  • Page 65: Qos

    Configuring QoS Overview With network scale expanding and applications developing, internet traffic is dramatically increased, thus resulting in network congestion, packet drops and long transmission delay. Typically, networks treat all traffic equally on FIFO (First In First Out) delivery basis, but nowadays many special applications like VoD, video conferences, VoIP, etc.

  • Page 66: Configuring Basic Qos

    Configuring QoS Configuring Basic QoS Configuring Basic QoS Configuration Guidelines Select the QoS mode according to your network requirements. Three QoS modes are supported on the switch: Port Based, 802.1P Based and DSCP Based.  Port Based The port based QoS mode supports four priority queues, which are labeled as 1 (Lowest), 2 (Normal), 3 (Medium) and 4 (Highest).

  • Page 67: Configuring Qos In Port Based Mode

    Configuring QoS Configuring Basic QoS Configuring QoS in Port Based Mode Choose the menu QoS > QoS Basic to load the following page. Figure 2-1 Configuring Basic QoS in Port Based Mode Follow these steps to configure QoS in port based mode: 1) In the Global Config section, select QoS mode as Port Based.

  • Page 68: Configuring Qos In 802.1P Based Mode

    Configuring QoS Configuring Basic QoS Configuring QoS in 802.1P Based Mode Choose the menu QoS > QoS Basic to load the following page. Figure 2-2 Configuring Basic QoS in 802.1P Based Mode Follow these steps to configure QoS in 802.1P based mode: 1) Select QoS mode as 802.1P Based.

  • Page 69: Configuring Bandwidth Control

    Configuring QoS Configuring Bandwidth Control Configuring Bandwidth Control Choose the menu QoS > Bandwidth Control to load the following page. Figure 3-1 Configuring Bandwidth Control Follow these steps to configure bandwidth control: 1) Select the desired ports and configure the ingress rate and egress rate for the ports. Ingress Rate Configure the bandwidth for receiving packets on the port.
  • Page 70 Configuring QoS Configuring Bandwidth Control Note: For a port, the ingress rate control feature and the storm control feature cannot be enabled • at the same time. If you enable ingress rate control for a port, storm control will be disabled for that port automatically.

  • Page 71: Configuring Storm Control

    Configuring QoS Configuring Storm Control Configuring Storm Control Choose the menu QoS > Storm Control to load the following page. Figure 4-1 Configuring Storm Control Follow these steps to configure storm control: 1) Select the desired ports and configure the upper rate limit for forwarding broadcast packets, multicast packets and UL-frames (Unknown unicast frames).
  • Page 72 Configuring QoS Configuring Storm Control Included Storm Select to filter broadcast/multicast/UL frame in the network. If the transmission Type rate of the chosen packets exceeds the total rate, the packets will be automatically discarded to avoid network broadcast storm. It is multi-optional. UL-Frame: If UL-Frame packets traffic exceeds the rate on the port, they will be discarded.

  • Page 73: Configuration Example For Basic Qos

    Configuring QoS Configuration Example for Basic QoS Configuration Example for Basic QoS Network Requirements As shown below, both RD department and Marketing department can access the internet. When congestion occurs, the traffic from two departments can both be forwarded and the traffic from the Marketing department should take precedence.

  • Page 74: Configuration Steps

    Configuring QoS Configuration Example for Basic QoS Configuration Steps 1) Choose the menu QoS > QoS Basic to load the following page. In the Global Config section, select QoS mode as Port Based. Click Apply. Figure 5-2 Configuring Basic QoS in Port Based Mode 2) In the Port Based Priority Setting section, specify the priority queue for port 1 as 1(Lowest) and click Apply.
  • Page 75 Figure 5-3 Setting Different Priorities for Port 1 and Port 2...

  • Page 76: Appendix: Default Parameters

    Appendix: Default Parameters Default settings of QoS basic configuration are listed in the following table. Table 6-1 Default Settings of QoS Basic Configuration Parameter Default Setting QoS Mode DSCP/802.1P Based Priority Queue 1 (Lowest) Default settings of Bandwidth Control configuration are listed in the following table. Table 6-2 Default Settings of Bandwidth Control Configuration Parameter...

  • Page 77: Configuring Poe

    Part 7 Configuring PoE CHAPTERS 1. Overview 2. Configuring PoE...

  • Page 78: Overview

    Powered device (PD) is a device receiving power from the PSE, for example, IP phones and access points. According to whether PDs comply with IEEE standard, they can be classified into standard PDs and non-standard PDs. Only standard PDs can be powered via TP-Link PoE switches.

  • Page 79: Configuring Poe

    Configuring PoE Configuring PoE Configuring PoE Choose the menu PoE > PoE config to load the following page. Figure 2-1 Configuring PoE Follow these steps to Configure PoE: 1) In the Global Config section, you can view the current PoE parameters. You can configure the System Power Limit.
  • Page 80 Configuring PoE Configuring PoE 2) In the Port Config section, select the ports you want to configure and specify the parameters. Click Apply. PoE Status Enable or disable the PoE function on corresponding port. The port can supply power to the PD when its status is enable. PoE Priority Select the priority level for the corresponding port.
  • Page 81 No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-Link Technologies Co., Ltd. Copyright © 2019 TP-Link Technologies Co., Ltd. All rights reserved. https://www.tp-link.com...
  • Page 82 We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
  • Page 83 • Consult the dealer or an experienced radio/TV technician for help. We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.
  • Page 84 EU declaration of conformity TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU. The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce Canadian Compliance Statement This device complies with Industry Canada license-exempt RSSs.
  • Page 85 此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要 TL-SG1016DE/TL-SG1016PE/TL-SG1024DE/TL-SG1218MPE 求採取某些適當的對策。（For ） 限用物質含有情況標示聲明書 限用物質及其化學符號 產品元件名稱 鉛 鎘 汞 六價鉻 多溴聯苯 多溴二苯醚 CrVI PBDE ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 外殼 — ○ ○ ○ ○ ○ 電源適配器 備考 1. “ 超出 0.1 wt %” 及 “ 超出 0.01 wt %” 系指限用物質之百分比含量超出百分比含量...
  • Page 86 Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk. Explanation of the symbols on the product label Symbol Explanation...

This manual is also suitable for:

Tl-sg1016deTl-sg1016peTl-sg1024deTl-sg108pe

Table of Contents

Save PDF