Commercial Mode Setup For Master Tv - LG 37LD320H Owner's Manual

Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel
search) is disabled if there is an Aux input active.
Commercial Mode Setup Procedure
1. Set Installer Menu Items
(Enter TV Installer Menu, see Installer menus for detailed instructions.)
a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER on
Installer remote. (This clears all installer menu custom settings, channel
labels / icons etc. and reloads the factory default settings.)
b. Set Item 003 BAND/AFC.
- Broadcast: set to 000.
- CATV: set to 001.
c. Set item 028 CH OVERIDE to 001. This allows access to channel search,
Auto Tuning and Channel List/Edit options in the Channel Menu.
d. Set other particular installer items that affect your TV programming net-
work. Enable/Disable Aux sources, set a Start Channel etc.
e. After all required installer menu item settings have been adjusted, press
ENTER on the remote to remove Installer Menu.
2. Set Up TV Features
(Channel, Picture, Audio, Lock, Time, Option, Digital Captions etc. See TV
Clonable options list and TV menus pages.)
3. Run Auto Tuning (Channel Search)
(Search for all available channels.) Go to the Channel Menu and access
the Auto Tuning option, follow onscreen instructions.
a. Edit Channel Scan. In the Channel Menu, access Channel Edit option.
• Add/Delete channels per your system requirements.
Note: Physical channel numbers are used to identify Virtual channels.
• Add familiar channel trademarks/logos like ABC, CBS, NBC etc. to the
Channel-Time onscreen display. In the Channel menu, select the Channel
Label option. Add identifiable labels (logos) for the end user to readily
know what common networks are available.
4. Transfer TV Setup to Internal TV Controller: 2-5-5 + Menu Mode
After the TV channel scan has been edited and channel label icons
added, enter the Installer menu. Once in the Installer menu, press 2-5-5
and MENU on the remote. This transfers the TV setup to the internal
controller box.
5. Add Custom Channel Labels for Analog Channels: 2-5-4 + Menu Mode
Enter Installer menu, press 2-5-4 and MENU. Add your own custom text
labels to channel onscreen displays. Note: Digital Channels often have a
broadcaster generated label. (See 2-5-4+Menu pages.)
When finished, to exit 2-5-4+Menu mode, press MENU.
Verify TV Setup
At this point, verify that the channel lineup, channel icons and custom
labels are correct. Make sure the TV features are set per your requirements.
Set item 028 Ch Overide to 000 to lock the channel scan. After the pre-
ceding has been completed, the Master TV setup is ready to be copied to a
Clone Programmer, see cloning options pages.
206-4118
This page provides an overview of a Master TV configuration.
- HRC: set to 002
- IRC: set to 003

Commercial Mode Setup for Master TV

XXLH240H INSTALLER MENU
000 INSTALLER SEQ
UPN 000-000-000-000
PTC V1.00.000 CPU V3.06.00
XXLH250H INSTALLER MENU
000 INSTALLER SEQ
UPN 000-000-000-000
PTC V1.00.000 CPU V3.06.00
XXLH260H INSTALLER MENU
000 INSTALLER SEQ
UPN 000-000-000-000
PTC V1.00.000 CPU V3.06.00
Typical TV Installer Menu
117 FACT DEFAULT
003 BAND/AFC
028 CH. OVERIDE
Adjust the settings for these
Installer Menu Items
DIGITAL 19-3
MONO STEREO SAP
WXYZ
Custom Text Label 'WXYZ' created in
2-5-4 + Menu (Add Channel Label) Mode
093 RJP AVAILABLE
Set 093 RJP Available to 001 if using a remote
028 CH. OVERIDE
After Master TV setup has been completed,
set item 028 Ch Overide to 000.
For 32LH240H
000
FPGA E0F1
For 32/37/42LH250H,
000
32/37/42LH255H
FPGA E0F1
For 37/42LH260H
000
37LH265H
FPGA E0F1
00X
00X
001
001
jack pack
000
P A G E 7