Table of Contents
Advertisement
Quick Links
GAS DRYER INSTALLATION INSTRUCTIONS
CANADIAN ELECTRIC DRYER INSTRUCTIONS
INSTRUCTIONS POUR L'INSTALLATION
DE LA SÉCHEUSE À GAZ (É.-U. ET CANADA)
ÉLECTRIQUE (CANADA UNIQUEMENT)
Table of Contents
DRYER SAFETY .......................................................................... 2
INSTALLATION REQUIREMENTS .............................................. 4
Tools and Parts ...................................................................... 4
LOCATION REQUIREMENTS ..................................................... 5
ELECTRIC DRYER POWER HOOKUP-CANADA ONLY ........... 7
GAS DRYER POWER HOOKUP ................................................. 7
INSTALL LEVELING LEGS .......................................................... 9
MAKE GAS CONNECTION ....................................................... 10
VENTING .................................................................................... 10
Venting Requirements ......................................................... 10
Plan Vent System ................................................................. 11
Install Vent System .............................................................. 12
CONNECT INLET HOSE (STEAM MODEL ONLY)................... 13
CONNECT VENT ....................................................................... 14
LEVEL DRYER ........................................................................... 15
COMPLETE INSTALLATION CHECKLIST ............................... 15
DOOR REVERSAL (OPTIONAL) ............................................... 16
INSTALLATION NOTES
__________________________________
Date of purchase:
________________________________
Date of installation:
_________________________________________
Installer:
____________________________________
Model number:
____________________________________
Serial number:
W10868945A
W10868946A-SP
Para una version de estas instrucciones en español, visite www.Whirlpool.com
Table des matières
SÉCURITÉ DE LA SÉCHEUSE ................................................. 26
EXIGENCES D'INSTALLATION................................................. 28
Outillage et pièces ............................................................ 28
EXIGENCES D'EMPLACEMENT .............................................. 29
SÉCHEUSE ÉLECTRIQUE RACCORDEMENT À
L'ALIMENTATION ÉLECTRIQUE - CANADA SEULEMENT ... 31
RACCORDEMENT D'UNE SÉCHEUSE À GAZ ....................... 31
INSTALLATION DES PIEDS DE NIVELLEMENT...................... 33
RACCORDEMENT AU GAZ ...................................................... 34
ÉVACUATION ............................................................................ 34
Exigences concernant l'évacuation ................................ 34
Planification du système d'évacuation ........................... 35
Installation du système d'évacuation .............................. 37
RACCORDEMENT DU TUYAU D'ALIMENTATION
(MODÈLE À VAPEUR UNIQUEMENT) ..................................... 37
RACCORDEMENT DU CONDUIT D'ÉVACUATION ................ 39
RÉGLAGE DE L'APLOMB DE LA SÉCHEUSE......................... 39
ACHEVER L'INSTALLATION LISTE DE VÉRIFICATION .......... 40
INVERSION DE LA PORTE (FACULTATIF) ............................... 40
NOTES CONCERNANT L'INSTALLATION
_____________________________________
Date d'achat:
_________________________________
Date d'installation:
______________________________________
Installateur:
________________________________
Numéro de modéle:
__________________________________
Numéro de série:
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Whirlpool WGD92HEFW1
Summary of Contents for Whirlpool WGD92HEFW1
-
Page 1: Table Of Contents
RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE......39 DOOR REVERSAL (OPTIONAL) ..........16 ACHEVER L’INSTALLATION LISTE DE VÉRIFICATION ..40 INVERSION DE LA PORTE (FACULTATIF) ....... 40 Para una version de estas instrucciones en español, visite www.Whirlpool.com INSTALLATION NOTES NOTES CONCERNANT L’INSTALLATION __________________________________... -
Page 2: Dryer Safety
DRYER SAFETY... -
Page 4: Installation Requirements
INSTALLATION REQUIREMENTS Tools needed for gas installations: TOOLS AND PARTS Gather the required tools and parts before starting installation. Tools needed for all installations: 8" or 10" pipe wrench 8" or 10" adjustable wrench (for gas connections) Flat-blade screwdriver #2 Phillips screwdriver Pipe-joint compound resistant to LP gas Parts supplied (all models):... -
Page 5: Location Requirements
Parts needed (steam models): DRYER DIMENSIONS Front view: 27" (686 mm) " Min. 5' (1.52 m) inlet hose (984 mm) Additional parts may be required, depending on your installation. 39" Max. Check local codes. Check existing electrical supply and venting. (990 mm) Read “Electrical Requirements”... - Page 6 Custom under counter installation: Installation Clearances For each arrangement, consider allowing more space for ease of installation and servicing; spacing for companion appliances and clearances for walls, doors, and floor moldings. Space must be large enough to allow door to fully open. Add spacing on all sides of dryer to reduce noise transfer.
-
Page 7: Electric Dryer Power Hookup-Canada Only
ELECTRIC DRYER POWER HOOKUP – GAS DRYER POWER HOOKUP CANADA ONLY ELECTRICAL REQUIREMENTS ELECTRICAL REQUIREMENTS It is your responsibility: To contact a qualified electrical installer. ■ To be sure that the electrical connection is adequate and in ■ conformance with Canadian Electrical Code, C22.1 – latest 120 Volt, 60 Hz, AC only, 15- or 20- amp fused electrical ■... - Page 8 GAS SUPPLY REQUIREMENTS GAS SUPPLY LINE Option 1 (Recommended Method) Flexible stainless steel gas connector: If local codes permit, use a new flexible stainless steel gas ■ connector (Design Certified by the American Gas Association or CSA International) to connect your dryer to the rigid gas ⁄...
-
Page 9: Install Leveling Legs
INSTALL LEVELING LEGS GAS SUPPLY CONNECTION REQUIREMENTS ⁄ ⁄ Use an elbow and a " flare x " NPT adapter fitting ■ between the flexible gas connector and the dryer gas pipe, as needed to avoid kinking. Use only pipe-joint compound. Do not use TEFLON tape. -
Page 10: Make Gas Connection
MAKE GAS CONNECTION VENTING (gas models only) Venting Requirements Connect gas supply to dryer A. Flared male fitting B. Non-flared male fitting Remove red cap from gas pipe. Using a wrench to tighten, connect gas supply to dryer. Use pipe-joint compound on threads of all non-flared male fittings. -
Page 11: Plan Vent System
Exhaust hoods: Plan Vent System An exhaust hood should cap the vent to keep rodents and ■ insects from entering the home. Choose your exhaust installation type Must be at least 12" (305 mm) from ground or any object ■ Recommended exhaust installation: that may obstruct exhaust (such as flowers, rocks, bushes, or snow). -
Page 12: Install Vent System
Special provisions for mobile homes: Long Vent System Chart Exhaust vent must be securely fastened to a noncombustible portion of mobile home and must not terminate beneath the Number of Type Angled mobile home. Terminate exhaust vent outside. 90° elbows of vent hoods Rigid metal... -
Page 13: Connect Inlet Hose (Steam Model Only)
CONNECT INLET HOSE Tighten couplings (STEAM MODEL ONLY) For non-steam models, skip to “Connect Vent.” The dryer must be connected to the cold water faucet using the new inlet hoses (not supplied). Do not use old hoses. NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. -
Page 14: Connect Vent
CONNECT VENT Attach long hose to dryer fill valve and tighten coupling Connect vent to exhaust outlet Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. -
Page 15: Level Dryer
COMPLETE INSTALLATION LEVEL DRYER CHECKLIST Level dryer Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped. Check that you have all of your tools. Dispose of/recycle all packaging materials. Place Be sure the water faucets are on. -
Page 16: Door Reversal (Optional)
DOOR REVERSAL (OPTIONAL) Move the door strike The following instructions are for models with a round and square-shaped doors. Tools needed: #2 Phillips screwdriver Min. 8" long TORX T25 ® †† screwdriver Reverse door swing round-shaped door flat glass – single handle Using a T25 screwdriver, remove the 2 screws securing the... - Page 17 Remove outer window assembly Reverse outer window assembly from trim ring Handle Fig. A Fig. A Fig. B Using a Phillips screwdriver, remove the 2 screws from the outer window retainer and rotate the outer window assembly clockwise until the square notches line up with the 4 tabs on the trim ring indicated with arrows in the figure A above.
- Page 18 Rotate and reassemble outer window Remove hinge and latch assembly to trim ring Latch Bottom of door Notches Fig. A Hinge Using a T25 screwdriver, remove the 3 screws securing ® the latch plate and latch backing plate and the 5 screws holding the hinge assembly in place.
- Page 19 Reinstall inner door assembly Reinstall door on dryer Bottom of door Using a T25 screwdriver, remove the 4 screws on the dryer. ® Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. Secure in place with the 4 T25 screws removed earlier.
- Page 20 Reverse door swing round-shaped door flat glass – double handle Remove inner door from outer door Remove door from dryer IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding. Using a T25 screwdriver, remove the 4 screws securing the ®...
- Page 21 Reinstall hinge and latch on Reinstall door on dryer opposite sides Using a T25 screwdriver, remove the 4 screws on the ® dryer. Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. Secure in place with Using a T25 screwdriver, reinstall the latch plate and latch ®...
- Page 22 Reverse door swing round-shaped door curved glass – double handle Remove inner door from outer door Remove door from dryer IMPORTANT: If the protective film has not yet been removed from the dryer, peel the film from the dryer door before proceeding.
- Page 23 Reinstall hinge and latch on Reinstall door on dryer opposite sides Using a T25 screwdriver, remove the 4 screws on the ® dryer. Insert the tabs on the hinge into the mounting slot and slide down to engage the top tab. Secure in place Using a T25 screwdriver, reinstall the latch plate and latch ®...
- Page 24 Reverse door swing square-shaped door Remove door from dryer Remove inner door from outer door Release tab Release tab Position the door with the inside of the door facing up. Using a T25 screwdriver, remove the 4 screws securing the ®...
- Page 25 Reinstall hinge and latch on Reattach door to dryer opposite sides Latch Hinge Using a T25 screwdriver, reinstall the 4 screws securing ® Using a T25 screwdriver, reinstall the latch plate and ® the door hinge to the dryer. hinge assembly on the opposite sides from which they were removed.
Need help?
Do you have a question about the WGD92HEFW1 and is the answer not in the manual?
Questions and answers