Advertisement

MS3A
Owner's Manual

Advertisement

Table of Contents
loading

Summary of Contents for Jensen MS3ABK

  • Page 1 MS3A Owner’s Manual...
  • Page 2: Table Of Contents

    MS3A CONTENTS Introduction ....................................3 Features ....................................3 Box Content ..................................3 Compliance ..................................3 Safety Information ................................4 Installation ....................................5 Mounting the Radio................................5 Auxiliary Input ..................................6 Line Output ..................................6 Wiring Diagram ..................................7 Operation....................................8 Basic Functions ...................................
  • Page 3: Introduction

    Thank for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen receiver for maximum enjoyment.
  • Page 4: Safety Information

    MS3A Safety Information  To ensure full satisfaction with the product, please read the entire instruction manual.  Keep instructions for future reference.  Follow all operation guidelines and adhere to all safety warnings and cautions to ensure safe use. ...
  • Page 5: Installation

    MS3A INSTALLATION Mounting the Radio Choose a mounting location on the dash board or instrument panel that will allow room behind to run radio cables to the power source. Consider how you will use the AUX IN, LINE OUT and USB connectors and route the appropriate extension cables to an accessible area.
  • Page 6: Auxiliary Input

    MS3A Auxiliary Input Connect a portable audio device to the Audio Input (AUX IN RIGHT/LEFT) on the back of the unit using RCA cables. Line Output The Line Out connectors (LINE OUT RIGHT/LEFT) on the back of the unit output a line-level analog signal. Use this output to connect to an external amplifier...
  • Page 7: Wiring Diagram

    MS3A Wiring Diagram PIN NO. WIRE COLOR DESCRIPTION PURPLE RIGHT REAR SPEAKER (+) PURPLE/BLACK RIGHT REAR SPEAKER () GREEN LEFT REAR SPEAKER (+) GREEN/BLACK LEFT REAR SPEAKER (-) BLUE POWER AMP REMOTE Note: Do not connect the red wire to a BLACK GROUND constant power connection.
  • Page 8: Operation

    OPERATION Basic Functions Power Press the JENSEN power button (1) to turn the unit on/off. Restore Factory Settings Perform the following steps to reset the radio to factory default settings: Press and hold the power button (1) to display the software version.
  • Page 9: Usb Mode

    MS3A Frequency Tuning Press the l<< or >>l button (6, 7) to fine tune the radio frequency. Channel Seek Press and hold the l<< or >>l button to seek strong radio frequencies. Preset Channel Store To manually store a favorite channel to one of the six preset channels, perform the following steps: Press the l<<...
  • Page 10: Bluetooth Operation

    MS3A Bluetooth Operation The MS3A includes built-in Bluetooth technology that allows you to connect this head unit to Bluetooth-enabled devices for streaming audio playback. About Bluetooth Technology Bluetooth wireless technology is a short-range wireless radio protocol. Operating in the 2.4 GHz range, it transmits audio and data at speeds up to 2.1 Mbit/s over a range of up to 10 meters.
  • Page 11 MS3A Pairing a Bluetooth Device Before you begin, consult the owner’s manual for the Bluetooth device you want to pair with the MS3A. Make sure the device is on and ready to receive a signal from the MS3A. With the MS3A in Bluetooth Audio mode, press and hold the MODE (8) button.
  • Page 12: App Operation

    JENSEN® Specialty Controller is the ultimate wireless remote control for your JENSEN stereo system. Store away your old remotes and enjoy the convenience of all the primary functions of your JENSEN stereo right from your phone or tablet by transforming your mobile device into a functional stereo remote control!
  • Page 13: Troubleshooting

    MS3A TROUBLESHOOTING Table 1: Troubleshooting Problem Solution No power If the power supply is connected to the vehicle accessory circuits but the engine is not on, switch the ignition key to “ACC” Fuse may be blown. Replace with 10AMP ATO fuse. No AM/FM Reception Antenna cable not connected;...
  • Page 14: Specifications

    MS3A SPECIFICATIONS General Frequency band(s) (for Bluetooth)..............2.4~2.4835GHz Maximum radio-frequency power transmitted (for Bluetooth).
  • Page 15 ASA Electronics Corporation www.asaelectronics.com www.jensenheavyduty.com ©2016 ASA Electronics Corporation v. 270616...

This manual is also suitable for:

Ms3a

Table of Contents