Related Manuals for Gigabyte SB93
Summary of Contents for Gigabyte SB93
- Page 2 FCC Complicance Statement / For Users in the USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These rules are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
- Page 3 Preface / 前言 Thank you for purchasing and adopting the SB Series as your favorite computer product. To assure the safe application of this product, please carefully read the following: 感謝您採購與愛用 SB 系列電腦產品。為確保您能安全地使用本產品，請您仔細閱讀以下說明： Please strictly follow the labeled warnings and instructions given. 請務必遵守產品中的標示警告及指示。...
- Page 4 Items included in the package / 系統包裝說明圖 Software & Manual / 程式光碟與使用手冊 *Foot Stand / 腳座 *Mouse (Option) / 滑鼠（選購） Specification with “Option” are subject to change without notice. 以”*”所標示的規格與實際產品有差異時，以實際出貨產品為準。 Other Product Specifications / 其他產品規格 Small Form Factor Chassis / 精簡型電腦機殼 Small Form factor motherboard / Small Form Factor 主機板...
- Page 5 Chassis / 電腦機殼 Dimensions= 284(D) mm x 88(W) mm x 359(H) mm 外觀尺寸= 284(D) mm x 88(W) mm x 359(H) mm This chassis is made with material complied with UL specification and designed for space saving, and it can be opened easily with thumbscrew. There are one 5.25”...
- Page 6 IV. Front and Rear Panel Components / 前後面板的裝置 ① ② ② ③ ③ Front & Rear Panel Components / 前後面板圖 1. Floppy Disc (Option) / 軟碟機（選購） 2. DVD-ROM (Option) / 光碟機（選購） 3. Power Button / 電源按鈕 MIC In / 麥克風 Line Out (Audio Out or Earphone) /音源輸出...
- Page 7 Voltage Selection Switch / 電壓設定開關 Select the correct voltage setting for your local area voltage before the computer system is plug to the power source. 請在接上電源前先確定是否已將電壓開關設定為 110V。 Installing the System / 系統設備安裝 1. Unscrew the rear casing and push the upper casing toward the front panel, then loose the hook to remove the front panel.
- Page 8 For Model VB3 only / VB3 機種適用： Unscrew the black bar and remove it either. 將黑色護桿上的螺絲卸下，並移除護桿。 2. After loosening the 3 front screws, pull out the Device disk Bay. 卸下前面板的 3 顆螺絲後，即可抽出光碟及軟碟機支架。...
- Page 9 3A. For Model VB2 / VB2 機種： Put the hard disk drive & DVD-ROM into the rack, and align the screws at the screw holes. 將硬碟機及光碟機放入支架中，並對準螺絲孔位鎖上螺絲。 3B. For Model VB3 / VB3 機種： Put the floppy disk drive & DVD-ROM into the rack, and align the screws at the screw holes.
- Page 10 4. CPU / 中央處理器 4-1. Evenly spread the heat dispersion paste on the CPU and make sure it totally cover the CPU. Insert the CPU on the CPU socket. Make sure that you have lifted the transversal lever and aligned the aslant side of the CPU along the aslant side of the CPU socket.
- Page 11 A. For Model VB2 / VB2 機種： B. For Model VB3 / VB3 機種： Fix the cooler on the rack / 將 CPU 風扇固定在 CPU 上 Click the heat sink locker to the motherboard retention module. 將風扇卡勾固定在風扇支架上 Install fan on top of CPU / 將 CPU 風扇放在 CPU 上 Latch the hooks on both sides of...
- Page 12 5. Memory / 記憶體 There are fixing grooves on both sides / 兩側有固定凹槽 Make sure the direction of the foolproof groove must be the same as that of the memory slot on the motherboard. 安裝主機板上的記憶體插槽時，其方向必須與防呆凹槽的方向相同才能順利安裝。 Fixing the hooks. The hooks must be fixed into the grooves before the installation is considered complete.
- Page 13 For Model VB3 only / VB3 機種適用： Align the screws at the black bar’s screw holes. Push the hard disk drive into the rack and align the screws at the screw holes, including 2 screws holes on the black bar. 將黑色護桿上的螺絲對準螺絲孔位鎖上...
- Page 14 HDD / 硬碟機 Note: If the first pin of the red cable doesn’t align to Pin 1 labeled on the hard disk and option devices, your hard disk and option devices will not work and may cause damage to the disk. 注意：若您未將排線上有紅色標示的第一腳對齊硬碟及選購光碟機上標示為...
- Page 15 7. Connecting the power supply / 連接電源供應器 A. For Model VB2 / VB2 機種： Connect the connector of the power supply to the power supply socket of the hard disk drive and option device. Follow above note. 將電源供應器上的電源接頭連接到硬碟及選購光碟機上的電源插座。注意事項同前。 HDD / 硬碟機 B.