Daikin EKHBRD014ABV1 Operation Manual
Indoor unit for air to water heat pump system and options
Hide thumbs
Also See for EKHBRD014ABV1:
- Installation manual (48 pages) ,
- Installation manual (48 pages) ,
- Installation manual (48 pages)
Subscribe to Our Youtube Channel
Related Manuals for Daikin EKHBRD014ABV1
Summary of Contents for Daikin EKHBRD014ABV1
- Page 1 OPERATION MANUAL Indoor unit for air to water heat pump system and options EKHBRD011ABV1 EKHBRD014ABV1 EKHBRD016ABV1 EKHBRD011ABY1 EKHBRD014ABY1 EKHBRD016ABY1...
-
Page 2: Table Of Contents
EKHBRD011ABV1 EKHBRD011ABY1 Indoor unit for air to water heat pump system Operation manual EKHBRD014ABV1 EKHBRD014ABY1 and options EKHBRD016ABV1 EKHBRD016ABY1 ONTENTS Page CAREFULLY READ THIS OPERATION MANUAL Introduction ..................1 BEFORE USING THE UNIT. IT WILL TELL YOU HOW TO USE THE UNIT PROPERLY AND HELP YOU IF ANY General information .............. -
Page 3: Quick Start-Up Of The Unit
Manual storage UICK START UP OF THE UNIT Push and hold the w button for In this chapter the step-by-step procedure is explained for starting up 5 seconds both space heating and domestic water heating. The more detailed information of how the unit must be operated is explained in the chapter "Operation of the unit"... -
Page 4: Remote Controller Buttons And Icons
11. TEMPERATURE DISPLAY Remote controller buttons and icons The display shows the current temperature of the installation either leaving water temperature or actual room temperature. 6 23 When changing the room temperature set point, the set point will be flashing for 5 seconds and then return to the actual room temperature. -
Page 5: Setting The Clock
24. DOMESTIC WATER HEATING BUTTON Setting the clock This button enables or disables the different domestic hot water modes in combination with the schedule timer button. After initial installation, the user can set the clock and day of the week. This button is not used when the domestic hot water tank is not The remote controller is equipped with a schedule timer that enables installed. -
Page 6: Leaving Water Temperature Control
Leaving water temperature control Selecting space heating operation Use the y button to switch ON/OFF space heating (h). In this mode, heating will be activated as required by the water temperature set point. The set point can be set manually, through the Icon h appears on the display as well as the corresponding schedule timer or weather dependent (automatic). -
Page 7: Domestic Water Heating Operation (W)
Field settings define the parameters for the weather dependent The setback function is configured through field settings. Refer to the operation of the unit. Refer to the chapter "Field settings" on page 15 chapter "Field settings" on page 15 for a detailed description how to for a detailed description how to set one or more field settings. -
Page 8: Automatic Storage
Automatic storage NOTE If weather dependent domestic water heating is In this mode, the indoor unit will deliver hot water to the domestic hot enabled [b-02], the storage temperature will be set water tank based on the daily fixed pattern. This mode will continue automatically and the field setting [b-03] will be of no until the storage temperature set point is reached. -
Page 9: Reheat
The storage temperature set point is a field setting. Refer to the The reheat minimum and reheat maximum temperature set points chapter "Field settings" on page 15 for a detailed description how to are field settings. Refer to the chapter "Field settings" on page 15 for set one or more field settings. -
Page 10: Other Operation Modes
Other operation modes Simultaneous demand of space heating and domestic water heating Start up operation (d) The unit can not perform domestic water heating and space heating During start up, the d icon displays, indicating that the heat at the same time. If both modes are requested at the same time, the pump is starting up and is not working in a steady state condition. -
Page 11: Schedule Timer Operation
Operation example: Schedule timer based on temperature set Schedule timer operation points. In schedule timer operation, the installation is controlled by the When setback function is enabled, the setback operation will have schedule timer. The actions programmed in the schedule timer will be priority over the scheduled action in the schedule timer. -
Page 12: Domestic Water Heating
Operation example: Schedule timer based on ON/OFF instruction. Domestic water heating When setback function is enabled, the setback operation will have Domestic water heating can be done through several standard priority over the scheduled action in the schedule timer if ON operation modes: instruction is active. -
Page 13: Programming And Consulting The Schedule Timer
Programming space heating Programming and consulting the schedule timer Programming the schedule timer is flexible (you can add, remove or alter programmed actions whenever required) and straightforward (programming steps are limited to a minimum). However, before programming the schedule timer, remind: Familiarize yourself with the icons and the buttons. -
Page 14: Programming Quiet Mode Or Domestic Water Heating
Programming space heating is carried out as follows: Programming quiet mode or domestic water heating Returning to previous steps in the programming NOTE procedure without saving modified settings is done by pressing the pr button. Press the < button to enter the programming/consulting mode. Select the operation mode you would like to program by means of the pi and pj buttons. -
Page 15: Consulting Programmed Actions
11 Press the < button for 5 seconds to store the programmed Deleting one or more programmed actions actions. Deleting one or more programmed actions is done at the same time If the < button is pressed when action number 3 is displayed, as storing the programmed actions. -
Page 16: Field Settings
When running through the field settings you may notice that there are some more field settings as there are The configuration of the Daikin system is done through field settings. mentioned in the "Field settings table" on page 16. These field settings are not applicable and may not be... -
Page 17: Field Settings Table
Field settings table Installer setting at variance with default value First Second Default code code Setting name Date Value Date Value value Range Step Unit Remote control setup Installation related setting — Installation related setting –5~5 °C Not applicable. Do not change the default value. 1 (ON) —... - Page 18 Installer setting at variance with default value First Second Default code code Setting name Date Value Date Value value Range Step Unit Automatic temperature compensation Installation related setting –2~2 °C Installation related setting –5~5 °C Installation related setting –5~5 °C Option setup Installation related setting —...
-
Page 19: Maintenance
(blank display) at regular intervals, preferably yearly. This maintenance should be • The benefit kWh rate power supply is carried out by your local Daikin technician (see installation manual). active (see installation manual). One of the error codes appears Consult your local dealer. - Page 20 NOTES...
- Page 21 NOTES...
- Page 22 NOTES...
- Page 24 4PW60971-1...
Need help?
Do you have a question about the EKHBRD014ABV1 and is the answer not in the manual?
Questions and answers