Download Print this page

Advertisement

Quick Links

Loose Parts
Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.
Dealer Pack
Part #
Literature Pack
Part #
Models and Required Completing Kits
Note: Use the following charts to verify the kits required for the unit you are installing the UltraVac on.
LHPUV4448
44 inch Deck
All Serial Numbers
48 inch Deck
Serial Numbers 203376 & Higher
LHPUV4650
46 inch Deck
All Serial Numbers
50 inch Deck
All Serial Numbers
LHPUV5256
52 inch Deck
All Serial Numbers
56 inch Deck
All Serial Numbers
* Required on units with a 2 post ROPS installed.
© 2008—Exmark Mfg. Co., Inc.
P.O. Box 808
Beatrice, NE 68310
Description
Warranty Registration Reminder
Description
Manual, Operator's
Manual, Parts
Qty.
Assembling the tubes.
Fill out the online warranty registration
form.
Qty.
1
Read before operating the machine.
1
Drive Kit
103-1315
Drive Kit
103-1314
Drive Kit
109-1013
Drive Kit
109-1014
Drive Kit
109-1185
Drive Kit
109-1015
ULTRA VAC
Lazer Z
®
Setup Instructions
For Serial Nos. 790,000 & Higher
Use
Use
Front Weight Kit*
103-5629
Front Weight Kit*
103-5629
Front Weight Kit
103-5629
Front Weight Kit
103-5629
Front Weight Kit*
103-5629
Front Weight Kit
103-5629
Part No. 4500-419 Rev. A
Printed in the USA
All Rights Reserved
®
HP

Advertisement

loading
Need help?

Need help?

Do you have a question about the ULTRA VAC 103-5629 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Exmark ULTRA VAC 103-5629

  • Page 1 Front Weight Kit All Serial Numbers 109-1015 103-5629 * Required on units with a 2 post ROPS installed. © 2008—Exmark Mfg. Co., Inc. Part No. 4500-419 Rev. A P.O. Box 808 Printed in the USA Beatrice, NE 68310 All Rights Reserved...
  • Page 2: Assembly Diagrams

    Assembly Diagrams Description #10 Flat Washer Description #10-24 Nyloc Nut Engine Guard 44, 46, 48, 50 units Blower Assembly Bagger Mount Rear Weight 52 Weldment inch and 56 inch units 5/16-18 X 1 inch Hex Head Screw Spacer 52 inch unit only Hood Assembly 5/16-18 X 1-3/4...
  • Page 3 UltraVac Drive Kit Ultra Vac Weight Kit – Units with a 2 post ROPS only Description Description Spacer, Asm, Weight Counterweight Plate, Weight (52 inch and 56 Mounting inch decks) (See 5/16-18 x 1 inch Figure 1) Hex Head Screw Pin, Chute Pivot 5/16-18 x 1 1/2 Pin, Hair...
  • Page 4 Safety Safety Alert Symbol This Safety Alert Symbol (Figure 3) is used both in this setup instructions and on the machine to identify important safety messages which must be followed to avoid accidents This symbol means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Figure 4 Install the chute with the tabs to the rear of the deck tabs as shown.
  • Page 5 operator’s manual. Do Not use the blade bolt to 7. Apply a light coat of Mobil HTS grease (or food prevent rotation. grade antiseize) to the top portion of the spindle shaft where the sheave mounts. 8. Install the double sheave (item 23) onto the right spindle shaft.
  • Page 6 46, 50, and 56 inch LHP Units the deck. Use the whizlock nut removed in step 2. Install the bolt with the head to inside of the deck. 1. Stop the engine, remove the key, and wait for all moving parts to stop. 11.
  • Page 7 2. Use the upper mounting holes of the weight mounting plate to mark the location to drill the mounting holes in the front panel of the floor pan. Remove the weight mounting plate and drill the 3/8 inch upper mounting holes in the front panel of the floorpan.
  • Page 8: Installing The Blower Assembly

    2. Insert the upper tube (item 6) into the hopper seal (item 4) – push in then pull out so that the seal is extended outward. 3. Align the dimple on the upper tube (item 6) with the end of hopper seal and center between the two screws (item 4) as shown in Figure 11.
  • Page 9 the tension on the latch to draw the blower up to the sure that you understand the controls, their locations deck, yet allow the release by hand. their functions and safety requirements. 2. Ensure the blower, belt cover, bags, tube and hood are in good condition, properly attached and latched.