Advertisement
Quick Links
Loose Parts
Use the chart below to verify that all parts have been shipped. Part numbers not shown are available on the dealer
extranet.
Dealer Pack
Part No.
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Literature Pack
Manual-Operator's
© 2020—Exmark Mfg. Co., Inc.
415 Industrial Row
Beatrice, NE 68310
Description
Bolt (3/8 x 1 inch)
Locknut (3/8 inch)
Bracket-Mounting, Left weight
Bracket-Mounting, Right weight
Washer
Bolt (5/8 x 2-3/4 inches)
Weight-Suitcase
Bracket-Stabilizer
Bolt-Carriage (5/16 x 3/4 inch)
Locknut (5/16 inch)
Self-tapping screw (5/16 x 3/4 inch)
Bolt (5/16 x 1 inch)
Frame-Pivot
Hairpin cotter
Rod
Washer
Latch rod
Hairpin cotter
Bagger top
Bagger screen
Grass Bag
Upper bagger tube
Pivot bracket
Bolt (5/16 x 1 inch)
Nut (5/16 inch)
Chute
Baffle (50-inch decks only)
COLLECTION SYSTEM
142-6386, 142-6387, 142-6388
Setup Instructions
For Bagger Serial Nos. 408,644,346 & Higher
(To fit Quest Units Serial Nos. 408,644,346 & Higher)
Qty.
4
6
1
Install the weights.
1
2
2
6
1
2
4
2
Install the attachment mount
2
1
2
2
2
1
Install the latch rod.
1
1
Assemble the bagger top–All Deck
Sizes.
1
2
1
Install the bagger top.
2
4
4
1
Install the chute–All deck sizes.
1
Attaching the Discharge Tube–All
Deck Sizes
Fill out the online warranty registration
form.
All Rights Reserved *4505-498* A
Part No. 4505-498 Rev. A
Printed in the Mexico.
Use
Advertisement
Related Manuals for Exmark 142-6386
Summary of Contents for Exmark 142-6386
- Page 1 Attaching the Discharge Tube–All — Deck Sizes Fill out the online warranty registration — form. Literature Pack Manual-Operator's © 2020—Exmark Mfg. Co., Inc. All Rights Reserved *4505-498* A Part No. 4505-498 Rev. A 415 Industrial Row Printed in the Mexico. Beatrice, NE 68310...
- Page 2 Installing the Weights CAUTION The bagger changes the weight distribution of the machine. Operating the machine without the front weights may cause an unstable condition which could result in a loss of control. Ensure the front weights are properly installed before operating the machine with the bagger attachment.
- Page 3 g300204 Figure 3 g300206 Figure 5 1. 5/16 x 3/4 inch carriage 2. 5/16 inch locknut bolt 1. 5/16 x 3/4 inch self-tapping screw Install the pivot frame to the machine frame as Install the bent, flared end of a rod into the keyed shown in Figure 4.
- Page 4 g033027 Figure 7 1. Hairpin cotter 2. Latch rod Assembling the Bagger Top— All Deck Sizes Turn the bagger top over. Install the screen as shown in Figure 8 so it slopes down toward the collection bags. Make sure the screens snap into place and the tabs engage the bagger top.
- Page 5 g207349 Figure 11 Install the upper bagger tube by inserting the curved g300208 Figure 9 end into the opening in the bagger top. Make sure the flared end with the retention post is pointing 1. Bagger posts 3. Nuts (5/16 inch) down and forward in preparation to be mated with 2.
- Page 6 For 34, 42, 54 Inch Decks: Proceed to Step 3. For 50 Inch Deck: Remove and retain the existing baffle and its mounting hardware from the machine. g300212 Figure 15 Tilt the chute and install the pin into the hole on the mower deck as shown in Figure 16.
- Page 7 Attaching the Discharge Tube– All Deck Sizes Slide the curved end of the discharge tube into the opening in the bagger top. g300375 Figure 17 Secure the chute to the deck. Hook the flexible latch g010641 on the chute to the retaining clasp welded on the Figure 19 mower deck to the rear of the opening.
Need help?
Do you have a question about the 142-6386 and is the answer not in the manual?
Questions and answers