Functional Description - Makita UH200DZ Instruction Manual

follow the safety rules stated in this instruction
manual may cause serious personal injury.
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter,
stop operating immediately. It may result in a risk
of overheating, possible burns and even an
explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
7. Do not incinerate the battery cartridge even if it is
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use dropped or struck battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Indication lamp
The lamp blinks in red.
The lamp lights up in red. (Note 1)
The lamp lights up in red. (Note 1)
Note 1: The time at which the indication lamp lights up varies by the temperature around the work area and the battery
cartridge conditions.
12
3. Charge the battery cartridge with room

FUNCTIONAL DESCRIPTION

ENC007-4
• Always be sure that the tool is switched off and the
Installing or removing battery cartridge
(Fig. 1)
• Always switch off the tool before insertion or removal of
• To remove the battery cartridge, withdraw it from the
• To insert the battery cartridge, hold it so that the battery
• Do not use force when inserting the battery cartridge. If
Switch action (Fig. 2)
• Before inserting the battery cartridge into the tool,
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, depress the lock-off button and pull the
switch trigger. Release the switch trigger to stop. The
lock-off button can be pressed from either right or left
side.
Indication lamp (Fig. 3)
Running the tool allows the indication lamp to show the
battery cartridge capacity status.
When the tool is also overloaded and has stopped during
operation, the lamp lights up in red.
Refer to the following table for the status and action to be
taken for the indication lamp.
Status
This indicates the appropriate time to
replace the battery cartridge when the
battery power becomes low.
This function works when the battery
power is almost used up. At this time,
tool stops immediately.
Autostop due to overload.
temperature at 10°C - 40°C (50°F - 104°F). Let a hot
battery cartridge cool down before charging it.
CAUTION:
battery cartridge is removed before adjusting or
checking function on the tool.
the battery cartridge.
tool while pressing the buttons on both sides of the
cartridge.
cartridge front shape fits to that of the battery
installment opening and slip it into place. Always insert
it all the way until it locks in place with a little click. If
not, it may accidentally fall out of the tool, causing
injury to you or someone around you.
the cartridge does not slide in easily, it is not being
inserted correctly.
CAUTION:
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
Recharge the battery cartridge as soon
as possible.
Recharge the battery cartridge.
Turn off the tool.
Action to be taken