Table of Contents
Advertisement
Circuit Descriptions, List of Abbreviations, and IC Data Sheets
•
IR. This input pin is connected to an RC5 remote control
receiver.
•
SEL-IF-LL'/ M-TRAP. For AP: All L04 AP sets are Multi
System QSS set. This is an output pin to switch the Video
SAW filter between M system and other systems.
–
0: NTSC M (default)
–
1: PAL B/G, DK, I, L
•
Write Protect. The global protection line is used to enable
and disable write protection to the NVM. When write to the
NVM is required, pin 7 of the NVM must be pulled to logic
'0' first (via Write_Protect of the micro-controller pin) before
a write is performed. Otherwise pin 7 of NVM must always
be at logic "1"
–
0: Disabled
–
1: Enabled (default)
•
Mute. This pin is use to MUTE the audio amplifier. It is
configured as push pull.
•
Rotation. This pin is configured as PWM for the Rotation
feature. The output of the PWM is proportional to the
feature control.
•
Light Sensor. This pin is configured as ADC input for the
Light Sensor.
•
Sel_SC2_Interface. This pin is use to switch between the
SC2_CVBS_OUT and the INTF_CVBS_OUT for the
SCART_2_CVBS_OUT/ MONITOR_OUT signal.
–
0: Hercules CVBS Output (default)
–
1: Interface CVBS Output
•
PWRDOWN. The AUX SMPS generates this signal. Logic
"high" (3.3 V) under normal operation of the TV and goes
"low" (0 V) when the Mains input voltage supply goes below
70 V_ac.
•
Keyboard. Following are the Keyboard functions and the
step values (8 bit) for it.
Table 9-6 Local keyboard values
Function
NAFTA Standby
Ch +
Exit Factory (Ch- and Vol-)
Ch -
Menu (Vol - and Vol +)
Vol -
DVD Eject
Vol +
•
SDM. This pin is configured as Open Drain during the cold
start only. If this pin is shorted to ground during cold start,
it will enter the SDM mode (for Service use).
•
ISP. This pin is configured as Open Drain during the cold
start only. If this pin is shorted to ground during cold start,
it will enter the ISP mode (for Service use).
•
PANEL. This pin is configured as Open Drain during the
cold start only. If this pin is shorted to ground during that,
then it will enter to the PANEL mode.
•
ResetEnabled. This is an output pin to switch the control
transistor (pos. TS7202) "high" or "low" for the reset of 1.8
V in case there is a corruption in the Hercules.
9.5
Tuner and IF
The tuner used in this chassis comes from two sources, from
Philips and from Alps. Both tuner sources have the same pin
configuration so they are 1 to 1 compatible except for the
software, which will be selected by means of Option Settings.
Some features:
•
Multi-Standard alignment free PLL-IF, including SECAM
L/L'.
•
Integrated IF-AGC time constant.
•
Integrated sound band-passes and traps (4.5 / 5.5 / 6.0 /
6.5 MHz).
•
Group delay compensation (for NTSC and for PAL).
Voltage (V_dc)
Step values (8 bit)
0
0 - 6
0.43
7 - 33
0.69
34 - 53
0.93
54 - 73
1.19
74 - 96
1.49
97 - 121
1.8
122 - 147
2.12
148 - 169
L04L AA
•
QSS versions with digital Second-Sound-IF SSIF (AM
demodulator for free).
•
FM mono operation possible: Inter-Carrier or QSS.
9.5.1
Diversity
The following Tuners can be present (depending on the region
and the set execution):
•
Normal tuner without PIP.
•
FM radio tuner without PIP.
•
Normal tuner with PIP (main tuner with splitter).
•
FM radio set with PIP (PIP tuner with splitter).
The SAW filter used, depends on the application concept
(whether it is a QSS concept or an Intercarrier):
•
OFWM3953M for QSS Video.
•
OFWK9656M for QSS Audio.
•
OFWM1971M for Intercarrier.
9.5.2
Pin Assignments and Functionality
Pin assignment of the Tuner:
Table 9-7 Pinning Tuner
Pin Pin Description
1
RF-AGC
2
FM Radio Input or N.C
3
NC (Address Pin)
4
SCL
5
SDA
6/7 Supply Voltage
8
N.C
9
Tuning Supply Voltage
10 FM Radio IF Output/Ground -
11 TV IF Output
Pin assignment of the several SAW filters (depends on region/
execution):
Table 9-8 Pinning SAW filters
QSS Video
QSS Video
Pin
(item 1002)
(item 1003)
1
Input
Input
2
Input Ground
Input Ground
3
Ground
Ground
4
Output
Output
5
Output
Output
6
-
n.c.
7
-
n.c.
8
-
Ground
9
-
Free
10
-
Switching input
The table below shows the switching behavior of SAW filter.
Table 9-9 Switching behavior SAW filter
High
System
M
Note: The logic level is measured at the base of transistor
7001.
9.
EN 87
DC Voltages
4V for Maximum Gain < 4V for Strong Signal
Condition
-
-
0 to 3.3 V_dc
0 to 3.3 V_dc
5 V_dc +/- 0.25 V
-
30 to 35 V_dc
-
QSS Audio
Intercarrier
(item 1001)
(item 1002)
Input
Input
Switching Input
Input Ground
Ground
Ground
Output
Output
Output
Output
-
-
-
-
-
-
-
-
-
-
Condition
Low
BG/DK/I/L
Advertisement
Table of Contents
