Related Manuals for Ubiquiti RP5AC-PRISM
Summary of Contents for Ubiquiti RP5AC-PRISM
- Page 1 5 GHz airMAX ® BaseStation with airPrism ® Active RF Filtering Technology Model: R5AC-PRISM...
-
Page 2: Package Contents
ESD events with industrial‑grade, shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable ™... -
Page 3: Hardware Overview
Hardware Overview Antenna RP-SMA RP-SMA Connector Antenna Antenna Connector: Connector: Chain 1 Chain 0 LED Panel Port Cover... - Page 4 LED Panel Signal In airOS®, you can modify the wireless signal strength threshold values for each LED on the Wireless tab under Signal LED Thresholds. The default values are shown below: LED will light blue when the wireless signal strength is above ‑65 dBm. LED will light blue when the wireless signal strength is above ‑73 dBm.
- Page 5 Ports Reset Button LAN Port The Gigabit Ethernet port is used to connect the power and should be connected to the LAN. Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the Rocket is powered on.
-
Page 6: Hardware Installation
Hardware Installation The Rocket5ac Prism is designed to mount directly onto a Ubiquiti airMAX RocketDish antenna for Point‑to‑Point use or ™ an airMAX Sector antenna for Point‑to‑MultiPoint use. 1. Lift the release latch on the bottom of the Rocket and slide the Port Cover off. - Page 7 4. Connect the RF cables (included with the antenna) to the RP-SMA Antenna Connectors located on top of the Rocket. 5. Attach the Rocket to the antenna. a. Align the mounting tabs on the back of the Rocket with the four mounting slots on the antenna. b.
- Page 8 6. Attach the other end of the RF cables to the RF connectors on the antenna. Connecting to a RocketDish Connecting to a Sector Antenna 7. Connect the GPS Antenna to the GPS Antenna Connector on the Rocket. Connecting the GPS Antenna Connecting the GPS Antenna...
- Page 9 8. Attach the protective shroud. Align the hash mark on the top Slide the protective shroud of the shroud with the notch on down over the Rocket until it the RocketDish. Rotate the shroud locks into place on the Sector clockwise until it locks into place.
-
Page 10: Connecting Power Over Ethernet
Connecting Power over Ethernet 1. Connect the Ethernet cable from the Rocket’s LAN port to the adapter’s POE port. 2. Connect an Ethernet cable from your LAN to the adapter’s LAN port. 3. Connect the Power Cord to the adapter’s power port. Connect the other end of the Power Cord to a power outlet. - Page 11 Accessing airOS Connect to the airOS Configuration Interface. 1. Make sure that your host system is connected via Ethernet to the Rocket. 2. Configure the Ethernet adapter on your host system with a static IP address on the 192.168.1.x subnet. 3.
-
Page 12: Installer Compliance Responsibility
Since Ubiquiti Networks equipment can be paired with a variety of antennas and cables, the Antenna Gain, Cable Loss, and Output Power fields are provided to the professional... -
Page 13: Specifications
Specifications Rocket5ac Prism Dimensions 88 x 40 x 230 mm (3.47 x 1.58 x 9.06") Weight 400 g (14.11 oz) Networking Interface (1) 10/100/1000 Ethernet Port RF Connectors (2) RP‑SMA (Waterproof ) (1) GPS (Waterproof ) LEDs (4) Signal Strength, GPS, Power, LAN Enclosure Die‑Cast Aluminum with White Powder Coating... -
Page 14: Safety Notices
Safety Notices Read, follow, and keep these instructions. Heed all warnings. Only use attachments/accessories specified by the manufacturer. WARNING: Do not use this product in location that can be submerged by water. WARNING: Avoid using this product during an electrical storm. -
Page 15: Limited Warranty
Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation;... - Page 16 No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS during the warranty period, and the Products being received at UBIQUITI NETWORKS’ facility freight prepaid in accordance with the RMA process of UBIQUITI NETWORKS.
-
Page 17: Limitation Of Liability
Limitation of Liability EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES (INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING... - Page 18 Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.
-
Page 19: Industry Canada
Industry Canada CAN ICES‑3(A)/NMB‑3(A) This Class A digital apparatus complies with Canadian CAN ICES‑003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. - Page 20 CAN ICES‑3(A)/NMB‑3(A) Cet appareil numérique de la classe A est conforme à la norme NMB‑003 du Canada. Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie.
-
Page 21: Australia And New Zealand
Australia and New Zealand Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. RoHS/WEEE Compliance Statement English European Directive 2012/19/EU requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. - Page 22 Español La Directiva 2012/19/UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 23: Declaration Of Conformity
[German] Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet. Ελληνική Δια του παρόντος, UBIQUITI NETWORKS, δηλώνει ότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σε συμμόρφωση με τις [Greek] βασικές απαιτήσεις και τις λοιπές σχετικές διατάξεις της οδηγίας 1995/5/ΕΚ. -
Page 24: Online Resources
. u b n t . c o m ©2015‑2017 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, airPrism, Prism, Rocket, RocketDish, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc.