Evolution R185 CCSL Original Instructions Manual
  1. Manuals
  2. Brands
  3. Evolution Manuals
  4. Saw
  5. R185 CCSL
  6. Original instructions manual

Evolution R185 CCSL Original Instructions Manual

185mm tct multi-material circular saw
Hide thumbs Also See for R185 CCSL:
Table of Contents

Advertisement

Quick Links

027-0001B, 027-0002B, 027-0003B
Original Instructions
GB2438285
Original written in UK English
Date Published:19/01/2018

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R185 CCSL and is the answer not in the manual?

Questions and answers

Related Manuals for Evolution R185 CCSL

Summary of Contents for Evolution R185 CCSL

  • Page 1 027-0001B, 027-0002B, 027-0003B Original Instructions GB2438285 Original written in UK English Date Published:19/01/2018...

  • Page 2: Table Of Contents

    www.evolutionpowertools.com TABLE OF CONTENTS INTRODUCTION Warranty Page 3 Specifications Page 4 Vibration Page 5 Labels and Symbols Page 6 Intended use of this Power Tool Page 6 Prohibited use of this Power Tool Page 6 SAFETY PRECAUTIONS Electrical Safety Page 6 Outdoor Use Page 7 General Power Tool Safety Instructions...

  • Page 3: Warranty

    Technical Helpline, the number of which can be found on the Evolution Power Tools website. We operate several Helplines throughout our worldwide organization, but Technical help is also available from your supplier.

  • Page 4: Specifications

    www.evolutionpowertools.com SPECIFICATIONS CCSL MACHINE SPECIFICATIONS Motor EU (220-240V ~ 50 Hz) 1200W Motor UK (110V ~ 50 Hz) 1200W No-Load Speed (min /rpm) 3700 Weight 4.2kg Dust Port Diameter Ø 30mm Max. Blade Bevel Angle (degrees) Power cable length CCSL CUTTING CAPACITIES Mild Steel Plate (MaxThickness) Mild Steel Box Section (Max.

  • Page 5: Vibration

    WARNING: Do not operate this machine and fingers closely. If any of the symptoms if warning and/or instruction labels are become evident, seek immediate missing or damaged. Contact Evolution medical advice. Power Tools for replacement labels. • The measurement and assessment of...

  • Page 6: Intended Use Of This Power Tool

    WARNING: This product is a Hand Operated Volts Circular Saw and has been designed to be Amperes used with special Evolution blades. Only use accessories designed for use in this machine Hertz and/or those recommended specifically by Evolution Power Tools Ltd.

  • Page 7: Outdoor Use

    www.evolutionpowertools.com OUTDOOR USE Do not use any adapter plugs with earthed (1.13) (grounded) power tools. Unmodified plugs WARNING: For your protection if this tool is to and matching outlets will reduce risk of be used outdoors it should not be exposed to electric shock.

  • Page 8: Health Advice

    www.evolutionpowertools.com f) Keep cutting tools sharp and clean. A wrench or key left attached to a rotating part of a power tool may result in personal injury. Properly maintained cutting tools with e) Do not overreach. Keep proper footing and sharp cutting edges are less likely to bind balance at all times.

  • Page 9: Safety Instructions For All Saws

    www.evolutionpowertools.com You should always: h) Never use damaged or incorrect blade washers or bolt. The blade washers and • Work in a well-ventilated area. • Work with approved safety equipment, such bolt were specially designed for your saw, for as dust masks that are specially designed to optimum performance and safety of operation.

  • Page 10: Additional Safety Instructions For Circular Saws

    www.evolutionpowertools.com ADDITIONAL SAFETY d) Do not use dull or damaged blades. INSTRUCTIONS Unsharpened or improperly set blades produce FOR CIRCULAR SAWS narrow kerf causing excessive friction, blade binding and kickback. a) Do not use High Speed Steel e) Blade depth and bevel adjusting locking (HSS) saw blades.

  • Page 11: Items Supplied

    If you are at all unsure about any aspect of the use, care or maintenance of an Evolution product, contact the relevant Evolution helpline where up to date information and...

  • Page 12: Machine Overview

    www.evolutionpowertools.com MACHINE OVERVIEW 1. CUT MATERIAL EJECTION PORT 10. DEPTH SCALE 2. THUMB LEVER 11. REAR HANDLE INCORPORATING SAFETY START ON/OFF SWITCH 3. MULTI-MATERIAL TCT BLADE 12. UPPER BLADE GUARD 4. LOWER BLADE GUARD 13. PRECISION ENGINEERED SOLE PLATE 5. PARALLEL EDGE GUIDE 14.

  • Page 13: Preparation

    (10.1) WARNING: Use only genuine Evolution blades (or those Fig. 1 approved by Evolution Power Tools), which are designed for use in these machines. Ensure that the maximum speed of the blade is compatible with the machine. Only perform this operation with the machine disconnected from the power supply.

  • Page 14: Parallel Edge Guide

    www.evolutionpowertools.com • Safely store the outer blade flange and associated fixings. • Rotate the lower blade guard up into the upper blade guard using the manual thumb lever. (Fig. 5) • Carefully remove the blade (if fitted) from the machine. •...

  • Page 15: Cutting Depth Adjustment

    www.evolutionpowertools.com WARNING: It is potentially dangerous to install, and try to use the Edge Guide with the arm passing through only one (1) of the machined rectangular sole plate slots. Adjust the edge guide so that it is at the required distance from the blade and tighten the adjusting screw.

  • Page 16: Operating Advice (Pre Operation Checks)

    Evolution Power Tools offers the following general advice on safe operational procedures and practices for the consideration of the operator. This advice cannot be exhaustive as Evolution has no influence on the type of workshops or working environments in which these machines may be used.

  • Page 17: Ppe

    www.evolutionpowertools.com (15) • The operator should wear all relevant PPE (Personal Protection Equipment) necessary for the task ahead. This could include safety glasses,,full face mask, dust masks, safety shoes etc. Note: All CCS series machines are equipped with a cutting line debris blower.

  • Page 18: Cutting Advice

    www.evolutionpowertools.com CUTTING ADVICE A thumb operated lever is provided on (17) the lower blade guard. With care, a skilled WARNING: The operator must always be operator can retract the blade guard aware of the position and routing of the manually, either partially or fully, allowing power cable.

  • Page 19: Checking & Replacing Carbon Brushes

    www.evolutionpowertools.com Note: The lower blade guard should be rotated (manually) up into the upper blade guard. This will help accurate positioning of the engineers square and thus aid the checking process. If adjustment is required: CCSL Turn the adjustment screw (Fig. 16) clockwise or counter clockwise using a Hex Key (not supplied) until the blade is at exactly 90 to the sole plate.

  • Page 20: General Maintenance & Cleaning

    www.evolutionpowertools.com GENERAL MAINTENANCE & CLEANING (20) Note: All maintenance must be carried out with the machine switched off and disconnected from the power supply. • Check that all safety features and guards are operating correctly on a regular basis. Only use this machine if all guards/safety features are fully operational.

  • Page 21: Declaration Of Conformity

    EC DECLARATION OF CONFORMITY The manufacturer of the product covered by this Declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below.
  • Page 22 Evolution Power Tools Ltd Evolution Power Tools LLC Evolution Power Tools SAS Venture One 8363 Research Drive 61 Avenue Lafontaine Longacre Close Davenport 33560 Holbrook Industrial Estate Iowa Carbon-Blanc Sheffield 52806 Bordeaux S20 3FR +44 (0)114 251 1022 +1 866-EVO-TOOL...

Table of Contents