Related Manuals for NEC MultiSync EA304WMi
Summary of Contents for NEC MultiSync EA304WMi
- Page 1 Desktop Monitor MultiSync EA274WMi MultiSync EA304WMi User’s Manual Please fi nd your model name in the label on the backside of monitor.
-
Page 2: Table Of Contents
Index Warning, Caution ..........................English-1 Registration Information .......................English-2 Recommended use ........................English-3 Contents ............................English-5 Quick Start ............................English-6 Controls ............................English-11 Specifi cations - EA274WMi ......................English-18 Specifi cations - EA304WMi ......................English-19 Features ............................English-20 Troubleshooting ..........................English-21 Using the Auto Brightness function ....................English-23 ControlSync ..........................English-24 TCO Certifi ed Edge Displays 2.0 ....................English-25 Manufacturer’s Recycling and Energy Information ...............English-26... - Page 3 This product can only be serviced in the country where it was purchased. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K.
-
Page 4: Registration Information
Registration Information FCC Information Use the attached specifi ed cables with the MultiSync EA274WMi (L273QL)/MultiSync EA304WMi (L303QW) monitor so as not to interfere with radio and television reception. The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet the following condition. -
Page 5: Recommended Use
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. - Page 6 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
-
Page 7: Contents
Contents Your new NEC monitor box* should contain the following: • MultiSync monitor with tilt/swivel/pivot/height adjust stand • Power Cord* • Video Signal Cable (DVI-D to DVI-D cable)* • Video Signal Cable (DisplayPort cable) • USB Cable* • ControlSync Cable (ø 2.5 stereo micro plug) •... -
Page 8: Quick Start
Quick Start To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” (page 3) before installation. 1. Turn off the power of your computer. 2. For a PC with DisplayPort output: Connect the DisplayPort cable to the connector of the display card in your system (Figure A.1). - Page 9 3. Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position. 4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer (Figure C.1a).
- Page 10 8. Turn on the computer and the monitor by touching the power key on the front bezel (Figure E.1). 9. No Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup. For further adjustments, use the following OSD controls: •...
- Page 11 Tilt and Swivel Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Figure TS.1 NOTE: Handle with care when tilting the monitor screen. Flexible Arm Installation This LCD monitor is designed for use with a fl...
- Page 12 Mount Flexible Arm This LCD monitor is designed for use with a fl exible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand to attach the arm to the monitor (Figure F.1). Caution: Use ONLY the screws (4 pcs) that were removed from the stand to avoid damage to the monitor or stand.
-
Page 13: Controls
Controls OSD (On-Screen Display) control keys on the front of the monitor function are as follows: To access OSD menu, touch any of the control keys. To change signal input, touch the SELECT key. NOTE: Exit OSD in order to change signal input. EA274WMi EA304WMi 1 Ambient Light Sensor... - Page 14 ECO TOOLS BRIGHTNESS Adjusts the overall image and background screen brightness. If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear. CONTRAST Adjusts the overall image and background screen brightness by input signal level. ECO MODE Decreases the amount of power consumption by reducing the brightness level.
- Page 15 HUMAN SENSING The sensor on the front side of the monitor detects the movement of a person by using the HUMAN SENSING function. The HUMAN SENSING has three settings: OFF: No human sensing. 1 (LIGHT): After it is detected that there is no person after a period of time, the monitor shifts to low brightness mode automatically to reduce the power consumption.
- Page 16 FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust” function and the “H.Size” function do not give you a satisfactory picture setting, a fi ne tuning can be performed by using the “Fine” function. For this a Moiré...
- Page 17 Tools VOLUME Controls the volume of the speakers or headphones. To mute the speaker output, touch the “PBP/RESET” key (EA274WMi), “ /RESET” key (EA304WMi). SOUND INPUT (HDMI, DisplayPort inputs only) This function selects Audio Input, HDMI or DisplayPort. When PBP MODE is “ON”, outputs the audio signal that is associated with the adjustable screen’s video signal (HDMI or DisplayPort) or the audio from the input audio jack (AUDIO INPUT) on the back of the monitor (right side of display below USB port).
- Page 18 USB POWER Selects a power relation of USB. AUTO: Power is supplied to USB downstream port depending on related power condition. ON: Power is always supplied to USB downstream port even when in power save mode or power OFF. NOTE: Power consumption depends on connected USB even when a monitor’s power is off. FACTORY PRESET Selecting Factory Preset allows you to reset all OSD control settings back to the factory settings.
- Page 19 ECO Information CARBON SAVINGS: Displays the estimated carbon savings information in kg. CARBON USAGE: Displays the estimated carbon usages information in kg. This is the arithmetic estimation, not actual measurement value. COST SAVINGS: Displays the electricity cost savings in balance. CARBON CONVERT SETTING: Adjusts the carbon footprint factor in the carbon saving calculation.
-
Page 20: Specifi Cations - Ea274Wmi
@ 60 Hz 1440 x 900* @ 60 Hz 1920 x 1080 @ 60 Hz 2560 x 1440 @ 60 Hz (Digital)......NEC DISPLAY SOLUTIONS cites recommended. 2560 x 1440 @ 50 Hz (Analog) Active Display Area Landscape: Horiz.: 596.7 mm/23.5 inches Vert.:... -
Page 21: Specifi Cations - Ea304Wmi
1440 x 900* @ 60 Hz 1920 x 1080 @ 60 Hz 2560 x 1440 @ 60 Hz 2560 x 1600 @ 60 Hz (Digital)......NEC DISPLAY SOLUTIONS cites recommended. 2560 x 1440 @ 50 Hz (Analog) Active Display Area Landscape: Horiz.: 641.3 mm/25.2 inches... -
Page 22: Features
- conversion factor is based on OECD publication of global CO2 emissions 2008 Edition). This monitor has a manufacturing carbon footprint of approximately 42.5 kg. Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors. -
Page 23: Troubleshooting
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. - Page 24 No Video • If no video is present on the screen, turn the Power key off and on again. • Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). • Some display cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power cord under low resolution with DisplayPort.
-
Page 25: Using The Auto Brightness Function
Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient lighting within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions. -
Page 26: Controlsync
ControlSync 1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT. 2. Follow the steps of DATA COPY. When the setting of the master monitor is adjusted, it will be copied and sent to the connected sub monitor(s) automatically. -
Page 27: Tco Certifi Ed Edge Displays 2.0
TCO Certifi ed Edge Displays 2.0 Congratulations! This product is TCO Certifi ed – for Sustainable IT TCO CertiÞ ed is an international third party sustainability certiÞ cation for IT products. TCO CertiÞ ed ensures that the manufacture, use and recycling of IT products reß... -
Page 28: Manufacturer's Recycling And Energy Information
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life. - Page 29 When you need to dispose of your NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased the product, or if applicable, follow any agreements made between yourself and NEC.