Desktop Monitor MultiSync EA245WMi-2 User’s Manual MODEL: EA245WMi, EA245WMi-BK The regulations for this monitor applied to one of model names listed above. Please find your model name in the label on the rear side of the monitor.
Index WARNING ............................English-1 CAUTION .............................English-1 Registration Information .......................English-3 Recommended use ........................English-4 Safety Precautions and Maintenance ..................English-4 Ergonomics ..........................English-5 Cleaning the LCD Panel .......................English-5 Cleaning the Cabinet ......................English-5 Quick Start ............................English-6 ControlSync ..........................English-11 Multiple monitors connection using DisplayPort ................English-12 Recovering from no image ......................English-13 Controls ............................English-14 Specifications ..........................English-21 Features ............................English-22...
CAUTION: Please use the power cord provided with this display in accordance with the power cord table. If a power cord is not supplied with this equipment, please contact NEC. For all other cases, please use the power cord with the plug style that matches the power socket where the monitor is located.
(4) The image shown in this user’s manual is indicative only. If there is inconsistency between the image and the actual product, the actual product shall govern. (5) Notwithstanding articles (3) and (4), NEC will not be responsible for any claims on loss of profit or other matters deemed to result from using this device.
WARNING: The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by NEC Display Solutions of America, Inc. in this manual. Failure to comply with this government regulation could void your right to operate this equipment.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
Quick Start For contents, please refer to the contents sheet. To attach the Base to the LCD stand: 1. Place monitor face down on a non-abrasive surface (Figure 1). 2. Please rotate the stand 90 degrees as shown in Figure 1. NOTE: Handle with care when pulling the stand.
3. Place hands on each side of the monitor to tilt the LCD panel 35-degree angle and lift up to the highest position. 4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer (Figure C.1a).
7. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet. NOTE: Please refer to CAUTION section of this manual for proper selection of AC power cord. 8.
Tilt and Swivel Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). Figure TS.1 NOTE: Handle with care when tilting the monitor screen. Flexible Arm Installation This LCD monitor is designed for use with a flexible arm.
Mount Flexible arm This LCD monitor is designed for use with a flexible arm. 1. Follow the instructions on how to Remove Monitor Stand for Mounting. 2. Using the specified 4 screws, attach the arm to the monitor (Figure F.1). Spring washer 12 mm Flat washer...
ControlSync 1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT. 2. Follow the steps of DATA COPY. When the setting of the master monitor is adjusted, it will be copied and sent to the connected sub monitor(s) automatically.
Multiple monitors connection using DisplayPort You can connect multiple monitors by using DisplayPort daisy-chain connection. For using as multiple monitors in MST (multi-stream transport) mode, setting should be DP OUT MULTISTREAM “AUTO” at each connected monitor. Please change the monitor setting which is connected to a computer last in the connected monitors. If monitors have no image, turn off the monitor who is connected to a computer then turn it on.
Recovering from no image If monitors have no image after setting DP OUT MULTISTREAM, please set as follows: 1. Turn off the computer. 2. Touch the “MENU” key to show the No Signal OSD menu. 3. Touch the “ ” key to show VIDEO INPUT menu. 4.
Controls OSD (On-Screen Display) control keys on the front of the monitor function are as follows: To access OSD menu, touch any of the control keys. To change signal input, touch the SELECT key. NOTE: Exit OSD in order to change signal input. 1 Ambient Light Sensor Detects the level of ambient lighting and the presence of a user, allowing the monitor to Human Sensor...
ECO MODE Decreases the amount of power consumption by reducing the brightness level. OFF: No function. 1: Sets brightness variable range from 0% to 60%. This setting can adjust brightness to a range in which power is reduced by 20% compared to the maximum brightness setting.
SENSOR SETTING (HUMAN SENSING) Adjusts the threshold level of human sensing. When the human icon is located on the right side of the white color bar or vermilion color wave, a person is not detected. NOTE: Once the OSD has been closed, Human sensor starts to work. START TIME (HUMAN SENSING) Adjusts the wait time of entering to low brightness mode or power saving mode when Human Sensor detects no person.
FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust” function and the “H.SIZE” function do not give you a satisfactory picture setting, a fine tuning can be performed by using the “FINE” function. For this a Moiré...
Color Color Control System: Color presets are available for adjusting color settings. (sRGB and NATIVE color presets are standard and cannot be changed). 1, 2, 3, sRGB, 5: Increases or decreases Red, Green or Blue color depending upon which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown by the bars.
POWER SAVE TIMER POWER SAVE TIMER allows the monitor to turn off automatically after continuing power saving mode for 2 hours. LED BRIGHTNESS You can adjust the blue LED brightness. DDC/CI This function allows the DDC/CI function ON or OFF. USB POWER Selects a power relation of USB.
DATA COPY To initiate data copy from the master monitor to the sub monitor(s), select “DATA COPY” and touch “SELECT”. A “PROCEEDING...” indicator will appear on the screen. NOTE: This function is only intended for the master monitor in ControlSync. All of the settings specified in the ControlSync chart (see page 11) will be copied from the master monitor to the sub monitor(s).
Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors, and are accurate at the time of printing. NEC reserves the right to publish updated carbon footprint values. ControlSync: Follow the steps of “DATA COPY” and copy the settings from the master monitor to the sub monitors by connecting the ControlSync cable.
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
No Video • If no video is present on the screen, turn the Power key off and on again. • Make certain the computer is not in a power-saving mode (touch the keyboard or mouse). • Some display cards do not output video signal when monitor is turned OFF/ON or disconnect/connect from the AC power cord under low resolution with DisplayPort.
Using the Zoom Function Allows you to use the entire screen area, significantly expanding the size. Allows the picture displayed in the center to expand. SETUP 1. Select FULL or ASPECT in EXPANSION to activate the Zoom function (see page 17). EXPANSION OFF 2.
Human sensing function Human sensing function reduces power consumption by detecting the movement of a person. The HUMAN SENSING has following two settings: MODE HUMAN SENSING SETTING No person in front of the monitor LIGHT BRIGHTNESS 0% DEEP Power saving mode Image of human sensing operation A.
Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient lighting within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.