Asus RS720A-E9-RS24-E User Manual page 21

Action PHASE
PSP Boot Loader
PSP Boot phase (Error Post
Codes)
ASUS RS720A-E9-RS24-E
POST CODE TYPE
0x39 Error
0x3A Error
0x3B Error
0x3C Error
0x3D Error
0x3E Error
0x3F Error
0x40 Error
0x41 Error
0x42 Error
0x43 Error
0x44 Error
0x45 Error
0x46 Error
0x47 Error
0x48 Error
0x49 Error
0x4A Error
0x4B Error
0x4C Error
0x4D Error
0x4E Error
0x4F Error
0x50 Error
0x51 Error
0x52 Error
0x53 Error
0x54 Error
0x55 Error
0x56 Error
0x57 Error
0x58 Error
0x59 Error
0x5A Error
0x5B Error
0x5C Error
0x5E Error
0x5F Error
0x60 Error
0x61 Error
0x62 Error
0x63 Error
0x64 Error
0x65 Error
0x66 Error
0x67 Error
0x68 Error
0x69 Error
0x6A Error
0x6B Error
0x6C Error
0x6D Error
0x94 Error
0x95 Error
0x96 Error
0x97 Error
0x98 Error
0x99 Error
0x9A Error
0x9B Error
0x9C Error
0x9D Error
0x9E Error
(continued on the next page)
DESCRIPTION
Unable to map an SMN address to AXI space
Unable to map a SYSHUB address to AXI space
The count of CCXs or cores provided by bootrom is not consistent
Uncompressed image size doesn't match value in compressed header
Compressed option used in case where not supported
Fuse info on all dies don't match
PSP sent message to SMU; SMU reported an error
Function RunPostX86ReleaseUnitTests failed in memcmp()
Interface between PSP to SMU not available.
Timer wait parameter too large
Test harness module reported an error
x86 wrote C2PMSG_0 interrupting PSP
A write to an L3 register failed
Mini-BL
Mini-BL CCP HMAC Unit-test failed
Potential stack corruption in jump to Mini BL
Error in Validate and Loading AGESA APOB SVC call
Correct fuse bits for DIAG_BL loading not set
The UmcProgramKeys() function was not called by AGESA
Secure unlock error
Syshub register programming mismatch during readback
Family ID in MP0_SFUSE_SEC[7:3] not correct
An operation was invoked that can only be performed by the GM
Failed to acquire host controller semaphore to claim ownership of SMB
Timed out waiting for host to complete pending transactions
Timed out waiting for slave to complete pending transactions
Unable to kill current transaction on host
One of: Illegal command
An SMBus transaction collision detected
Transaction failed to be started or processed by host
An unsolicited SMBus interrupt was received
An attempt to send an unsupported PSP-SMU message was made
An error/data corruption detected on response from SMU for sent msg
MCM Steady-state unit test failed
S3 Enter failed
AGESA BL did not set PSP SMU reserved addresses via SVC call
CcxSecBisiEn not set in fuse RAM
Received an unexpected result
VMG Storage Init failed
Failure in mbedTLS user app
An error occured whilst attempting to SMN map a fuse register
Fuse burn sequence/operation failed due to internal SOC error
Fuse sense operation timed out
Fuse burn sequence/operation timed out waiting for burn done
Failure status indicating that the given SecureOS has been
This PSP FW was revoked
The platform model/vendor id fuse is not matching the BIOS public key
token
The BIOS OEM public key of the BIOS was revoked for this platform
PSP level 2 directory not match expected value.
BIOS level 2 directory not match expected value.
HVB validation failure for BIOS RTM volume (OEM public/signature failed
to validate).
Generic error indicating the CCP HAL initialization failed
Knoll failed to idle correctly after being reset
Bad status returned by I2CKnollCheck
NACK to general call (no device on Knoll I2C bus)
Null pointer passed to I2CKnollCheck
Invalid device-ID found during Knoll authentication
Error during Knoll/Prom key derivation
Null pointer passed to Crypto function
Error in checksum from wrapped Knoll/Prom keys
Knoll returned an invalid response to a command
Bootloader failed in Knoll Send Command function
No Knoll device found by verifying MAC
1-11