Advertisement
Preparing the filter for use
1
Mount the blender jar, with the blade unit attached onto the motor unit (A)
and fix it by turning it clockwise until you hear a 'click'. The blender jar can be
mounted in two positions (fig. 3 and fig. 4).
2
Put the filter (K) in the blender jar (fig. 6).
Make sure that the grooves of the filter fit exactly onto the ribs inside the blender
jar.
3
Make sure that the appliance is plugged in.
How to use the filter
1
Place the lid (F) on the blender jar.
Cut fruits into smaller pieces or pre-soak dry hard beans, such as soy beans, before
putting into filter.
2
Put the ingredients in the filter (fig. 7). Do not fill the filter beyond the top of
the sieve mesh.
3
Pour water or another liquid (milk, juice, etc.) into the blender jar.
4
Insert the measuring cup (G) into the hole in the lid.
Let the appliance run for approx. 40 seconds.
5
Switch the appliance off and remove the blender jar from the motor unit.
6
Pour the drink out via the pouring lip of the blender jar (fig. 8).
Do not remove the lid, the measuring cup and the filter.
7
For optimal results, put the jar with the remaining ingredients back onto the
appliance and let it run for a few more seconds.
Note: when you are processing a large quantity, we advise you not to put all the
ingredients in the filter at the same time. Start processing a small quantity and let the
appliance run for a few seconds. Then switch the appliance off and add another small
quantity, but do not exceed the top of the sieve mesh. Repeat this procedure until
you have processed all the ingredients. Always keep the lid on the blender jar during
processing.
Soy milk
Can only be prepared with the filter.
Do not process more than two batches without interruption. Let theappliance
cool down to room temperature before continue processing.
Ingredients
-
50g dry soybeans
-
500ml water
™
Soak the soy beans for 4 hours before processing them. Set aside to drain.
™
Put the soaked soy beans in the filter.
™
Pour 500ml of water in the blender jar and blend for 40 seconds.
™
Pour the milk into a pan. Bring the soy milk to the boil, then add sugar and leave
to simmer until all the sugar has melted. Serve hot or cold.
Mill (Only types HR 1721 and HR 1727)
How to use the mill
1
Put the ingredients in the jar (H) (fig. 9).
You can process wet and dry ingredients.
2
Do not fill the jar beyond the "MAX" indication.
3
Put the larger sealing ring (I) on the blade unit of the mill (J) (fig. 10).
Make sure that the rubber sealing ring has been placed correctly.
4
Screw the blade unit on the jar by turning it clockwise (fig. 11).
5
Hold the assembled mill upside down and screw it onto the motor unit (A) by
turning it clockwise until you hear a 'click' (fig. 12).
6
Make sure that the appliance is plugged in.
7
Switch the appliance on and let it run until the ingredients are fine enough.
This will take approx. 10-30 seconds.
4222 002 29382
Disassemble the mill
1
Unplug the appliance.
2
If the mill is still attached to the motor unit, turn the mill upside down and
remove the mill from the motor unit by turning it anticlockwise.
3
Remove the blade unit from the jar by turning it anticlockwise.
4
Always clean the removable parts immediately after use
Cleaning
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
We advise you to clean all the removable parts immediately after use.
Always unplug the appliance before cleaning.
Never clean the motor unit, the blade units, the filter and the sealing rings in
the dishwasher.
Always disassemble all removable parts before cleaning them. Do not forget
to remove the sealing rings from the blade units (blender and mill).
Avoid touching the blades. The blades are very sharp.
The blender and mill jar (without blade unit), lid and measuring cup are dishwasher-
proof.
Motor unit
Clean the motor unit with a moist cloth. Do not rinse the motor unit under
the tap. Do not use abrasives, scourers, alcohol, etc.
Storage
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
Wind excess mains cord round the base of the appliance.
Information & service
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
If you need information or if you have a problem, please visit the Philips Web site at
www.philips.com or contact the Philips Customer Care Centre in your country (you
will find its phone number in the worldwide guarantee leaflet). If there is no
Customer Care Centre in your country, turn to your local Philips dealer or contact
the Service Department of Philips Domestic Appliances and Personal Care BV.
3/7
Advertisement
