IMPORTANT– Read and Follow! • Before beginning, please read these Your safety and the safety of others is instructions completely and carefully. very important. We have provided many important safety • DO NOT remove permanently affixed messages in this manual and on your labels, warnings, or plates from product.
Page 4
• The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Page 5
IMPORTANT– Read and Follow! WARNING DANGER MOVING HAZARD CHEMICAL HAZARD To avoid risk of severe personal To avoid risk of property damage injury; this appliance requires two and/or personal injury or death; this appliance is not too be used or more personnel while handling as a heating source.
Specifications C/VGR530 C/VGR536 29-7/8” (75.9 cm) Overall width 35-7/8” (91.1.6 cm) Overall height To top of side trim –35-7/8” (91.1 cm) min. 37” (94.0 cm) max. Legs adjust – 1-1/8” (2.8 cm) Overall depth from To end of side panel - 24-5/16” (61.8 cm) rear* To front of door - 25-3/4”...
Page 9
Specifications C/VGR548 C/VGR560 47-7/8” (121.6 cm) Overall width 60” (152.4 cm) Overall height To top of side trim –35-7/8” (91.1 cm) min. 37” (94.0 cm) max. Legs adjust – 1-1/8” (2.8 cm) Overall depth from To end of side panel - 24-5/16” (61.8 cm) rear* To front of door - 25-3/4”...
Clearance Dimensions (Proximity to Cabinets) • This range may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. IMPORTANT: The side trim MUST be 3/8” (.95 cm) above the adjacent base cabinet countertop. This can be - 7 / ( 7 5 8 ”...
Clearance Dimensions (Wood/Composite Overlay) The bottom of a standard hood should be 30” (76.2 cm) min. to 36” (91.4 cm) max. / C o above the countertop. This would o s i e r l typically result in the bottom of the hood being 66”...
Electrical & Gas Requirements Electrical Requirements - Gas Ranges Pressure Regulator: Check your national and local codes regarding • All heavy-duty, commercial type cooking this unit. This range requires 120VAC/60 Hz; 4 ft. equipment must have a pressure (121.9 cm), 3-wire cord with grounded 3-prong regulator on the incoming service line plug attached to unit.
Page 13
Electrical & Gas Requirements Flexible Connections: If the unit is to be installed with flexible couplings and/or quick-disconnect fittings, the installer must use a heavy-duty AGA design-certified flexible connector of at least 1/2” (1.3 cm) ID NPT (with suitable strain reliefs) in compliance with ANSI Z21.41 and Z21.69.
General Information READ AND FOLLOW ALL WARNING AND CAUTION INFORMATION WHEN INSTALLING THIS APPLIANCE. • All openings in the wall behind the appliance and in the floor under the appliance must be sealed. • DO NOT obstruct the flow of combustion and ventilation air. NOTICE CAUTION DO NOT use the handle or oven door...
Leg Installation Note: It is strongly recommended Legs are packed in cardboard top pack. Note: Legs that a pallet or lift jack be used rather than tilting. Raise should be installed near to where appliance is to be unit about a foot. Unscrew shipping bolts from couplings on used, as they are not secure for long transit.
Page 17
Installation 0 . 9 Move unit into opening. Check that unit is level side to side and front to back. Side trim of the lowest corner must be 3/8” (0.95 cm) above countertop. If leveling is required, move unit out of opening. Lift unit and prop on wood blocks.
Installation Anti-tip Device Installation (Wall Mount) WARNING TIPPING HAZARD To reduce the risk of property damage or personal injury; install anti-tipping device provided in accordance with the installation instructions in this document. Device must be engaged properly to prevent product from tipping over.
Installation Connecting Gas & Electric DANGER GAS LEAK HAZARD To avoid risk of personal injury or death; leak testing of the appliance must be conducted according to the manufacturer’s instructions. Before placing appliance in operation, always check for gas leaks with soapy water solution. •...
Installation Check that unit is level side to side Burner heads and bases are packed in cardboard top and front to back. The side trim must be 3/8” (0.95 pack with the grates. Place burner bases on top of the cm) above countertop.
Final Preparation • All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner designed for this material. If buildup occurs, DO NOT use steel wool, abrasive cloths, cleansers, or powders! If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wooden or nylon scraper.
Only authorized replacement parts may be used in performing service on the appliance. All servicing should be referred to a qualified technician. Contact Viking Range, LLC, 1-888-(845-4641), for the nearest service parts distributor in your area or write to: VIKING RANGE, LLC...
Page 24
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-(845-4641) or visit vikingrange.com in the US or brigade.ca in Canada 055065-000A EN (031517)