Operation - Makita CL107FDZ Instruction Manual

NOTICE:
To prevent dust from getting into the
motor:
• Make sure that the dust bag or paper filter is
installed before use.
Insert the dust stopper together with the
•
dust bag or paper filter all the way into the
slots when installing them.
Do not use a broken or ripped bag.
•
Otherwise the motor may be broken.
NOTICE:
Do not fold the cardboard at its open-
ing when installing the paper filter.
NOTICE:
Never throw away the dust stopper
because it needs to be used repeatedly whenever
either the dust bag or the paper filter is used.
NOTICE:
The paper filter for the cleaner is an
important component for maintaining the tool
performance. Using other than the genuine paper
filter may cause smokes or ignition.
Installing dust bag
Use the dust stopper when installing dust bag. Be
careful not to take the upper side for the lower side by
mistake because they are different each other.
► Fig.11: 1. Upper side of dust stopper 2. Lower side
of dust stopper
1. Insert the protrusion of the dust bag into the
groove in the dust stopper as shown in the figure.
► Fig.12: 1. Dust stopper 2. Groove 3. Dust bag
2.
There is no distinction between the upper and
lower sides of the dust bag. You may insert its protru-
sion of either side into the lower groove of the dust
stopper.
► Fig.13: 1. Lower groove
3. Overlap the frame of dust stopper with that of the
dust bag.
► Fig.14
4. Place the dust stopper and the dust bag together
into the cleaner cavity in the same direction of arrow on
the dust stopper. Insert them all the way into the slots in
the cleaner cavity.
► Fig.15: 1. Cleaner cavity
5.
Place the entire cloth part of the dust bag inside
the cleaner itself.
► Fig.16
6. Close the front cover completely.
► Fig.17: 1. Front cover
Installing the paper filter
Use the dust stopper also when installing paper filter.
Be careful not to take the upper side for the lower side
by mistake because they are different each other.
► Fig.18: 1. Upper side of dust stopper 2. Lower side
of dust stopper
1.
Unfold the entrance of the paper filter before
setting it on the dust stopper.
► Fig.19
2. Insert the protrusion of the paper filter into the
groove in the dust stopper as shown in the figure.
► Fig.20: 1. Dust stopper 2. Groove 3. Paper filter
3.
There is no distinction between the upper and
lower sides of the paper filter. You may insert its pro-
trusion of any side into the lower groove of the dust
stopper.
► Fig.21: 1. Lower groove
4. Overlap the frame of dust stopper with that of the
paper filter.
► Fig.22
5. Place the dust stopper and the paper filter
together into the cleaner cavity in the same direction of
arrow on the dust stopper. Insert them all the way into
the slots in the cleaner cavity.
► Fig.23
6.
Place the entire container part of the paper filter
inside the tool itself.
► Fig.24
7. Close the front cover completely.

OPERATION

To connect attachments, such as nozzle, twist and
insert the attachment securely. To disconnect the
attachments, twist and extract it.
► Fig.25
Cleaning (Suction)
Nozzle
Attach the nozzle to clean off tables, desks, furniture,
etc. The nozzle slips on easily.
► Fig.26: 1. Nozzle
Nozzle + Extension wand (Straight
pipe)
The extension wand fits in between the nozzle and the
cleaner itself. This arrangement is convenient for clean-
ing a floor in a standing position.
► Fig.27: 1. Cleaner body 2. Extension wand
3. Nozzle
Corner nozzle
Fit on the corner nozzle for cleaning corners and crev-
ices of a car or furniture.
► Fig.28: 1. Corner nozzle 2. Cleaner body
Corner nozzle +Extension wand
(Straight pipe)
In tight quarters where the cleaner itself cannot
squeeze in, or in high places hard to reach, use this
arrangement.
► Fig.29: 1. Corner nozzle 2. Extension wand
3. Cleaner body
12 ENGLISH