Table of Contents
Advertisement
Available languages
Available languages
Assembly
Warning! Before assembly, remove the battery from the
tool.
Fitting and removing the battery (FIG. B)
•
To fit the battery (7), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
•
To remove the battery, push the release button (13)
while at the same time pulling the battery out of the
receptacle.
Fitting and removing a drill bit or screwdriver bit
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits.
•
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
•
Open the chuck by turning it (4) with one hand while
holding the tool with the other.
•
Insert the bit shaft into the chuck.
•
Firmly tighten the chuck by turning it (4) with one hand
while holding the tool with the other.
This tool is supplied with a double-ended screwdriver bit in
the bit holder (6).
•
To remove the screwdriver bit from the bit holder, lift the
bit from the recess.
•
To store the screwdriver bit, firmly push it into the holder.
Use
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, floors or ceilings, check
for the location of wiring and pipes.
Charging the battery (FIG.A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that
were easily done before. The battery may become warm
while charging; this is normal and does not indicate a
problem.
Warning! Do not charge the battery at ambient tempera-
tures below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 0 °C or above 40
°C. The battery should be left in the charger and the
charger will begin to charge automatically when the cell
temperature warms up or cools down.
•
To charge the battery (7), insert it into the charger (11).
(Original instructions)
The battery will only fit into the charger in one way. Do not
force. Be sure that the battery is fully seated in the
charger.
•
Plug in the charger and switch on at the mains.
The charging indicator (12) will flash green (slowly).
The charge is complete when the charging indicator (12)
lights green continuously. The charger and the battery can be
left connected indefinitely with the LED illuminated. The LED
will change to flashing green (charging) state as the charger
occasionally tops up the battery charge. The charging
indicator (12) will be lit as long as the battery is connected to
the plugged-in charger.
•
Charge discharged batteries within 1 week. Battery life
will be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the
charging indicator (12) will flash red at a fast rate. Proceed as
follows:
•
Re-insert the battery (7).
•
If the charging indicators continues flashing red at a fast
rate, use a different battery to determine if the charging
process works properly.
•
If the replaced battery charges correctly, the original
battery is defective and should be returned to a service
centre for recycling.
•
If the new battery gives the same indication as the
original battery, take the charger to be tested at an
authorised services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the direction of rotation (FIG. C)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
•
To select forward rotation, push the forward/reverse slider
(2) to the left.
•
To select reverse rotation, push the forward/reverse slider
to the right.
•
To lock the tool, set the forward/reverse slider into the
centre position
ENGLISH
7
Advertisement
Table of Contents
