Page 3
ENGLISH Congratulations to the purchase of this Beamz product. Please read this manual thoroughly prior to using the product in order to benefit fully from all features. Read the manual prior to using the product. Follow the instructions in order not to invalidate the warranty. Take all precautions to avoid fire and/or electrical shock.
UNPACKING INSTRUCTION CAUTION! Immediately upon receiving the product, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition. Notify the shipper immediately and retain packing material for inspection if any parts appear damage from shipping or the package itself shows signs of mishandling.
OVERVIEW 1. Fixture buttons (1 – 12) Used to select relevant fixture for control. 9. Music/Bank Copy Used to activate Music mode or to create scenes and 2. Scene buttons (1-8) chase programs. Press the scene buttons to load or stored your scenes. There are a maximum of 240 programmable scenes.
1.0 OPERATION GUIDE GENERAL This unit allows you to program 12 fixture of 16 DMX channels, 30 banks of 8 programmable scenes, 6 chases of 240 programmed scenes using 8 faders and other function buttons. To tailor your special effect lighting, this unit enables you to assign or reverse the DMX channels.
6. Tap the Bank Up/Down button to select the bank you want to store your scene into. There are total 30 banks you can select, you may store up to 8 scenes into each bank. 7. Tap the Scene button to store your scene, all LEDs and the Segment Display will flash three times briefly indicating this operation, then the Segment Display will show the bank and the scene.
1.4 SCANNER COPY This function allows you to copy the settings of one scanner to another. 1. Press and hold down the Scanner button you want to copy. 2. While holding the Scanner button, tap the Scanner button you want to copy to. 1.5 SCENE COPY 1.
1.7 DELETE ALL SCENES This function will reset all DMX channel to 0 output. 1. With the power off, press and hold down the Program and Bank Down buttons at a time. 2. Apply power again, all scenes should be cleared. 1.8 BANK COPY 1.
2.1 PROGRAM A BANK OF SCENES INTO A CHASE 1. Program enable. 2. Select the chase using Chase buttons 1-6. 3. Use Bank Up/Down button to select the bank that contains the scenes you wish to copy. 4. Tap the Music/Bank Copy button. 5.
2.3 DELETE A STEP 1. Program enable. 2. Select the chase that contains the step you wish to delete. 3. Tap the Tap Sync/Display button causing the Segment Display shows the steps. 4. Tap the Bank Up/Down button to scroll to the step you wish to delete. 5.
2. Use the Bank Up/Down button to select a bank of scenes to run. 3. After selecting the bank of scenes you wish to run, you can use the Speed slider (or Tap Sync/ Display button) and Fade Time slider to adjust the scenes to your desired effect. Hints: The Tap Sync button is used to set the speed by tapping the button several times, the last two taps will define the speed with a maximum of 10 minutes.
4.0 RUNNING CHASES You must program scenes before you can run chases. 4.1 MANUAL MODE 1. When the power is turned on, this unit enters Manual mode automatically. 2. Select your desired chase by tapping one of the six Chase buttons. A second tap of this button will deactivate this function.
Page 14
TECHNICAL SPECIFICATION / TECNISCHE SPECIFICATIE / TECHNISCHE DATEN / ESPECIFICACIONES TÉCNICAS / SPÉCIFICATIONS TECHNIQUES / SPECYFIKACJA TECHNICZNA : DC 9 – 12V, 300mA min. Rated voltage DMX Connection : 3-Pin XLR Function : DMX Dimensions per unit : 482 x 132 x 75mm Weight (per unit) : 2.6 kg The specifications are typical.
Page 15
Declaration of Conformity Manufacturer: TRONIOS BV Bedrijvenpark Twente 415 7602 KM – ALMELO +31(0)546589299 +31(0)546589298 The Netherlands Product number: 154.060 Product Description: DMX192S Controller Trade Name: BEAMZ EN 60598-1/-2 Regulatory Requirement: EN 60335-1 EN 55014-1/-2 EN 61000-3 I hereby declare that the product meets the requirements stated in Directives 2014/35/EU and 2014/30/EU and conforms to the above mentioned Declarations.