Related Manuals for Jet JAT-404
Summary of Contents for Jet JAT-404
- Page 1 Pneumatic Die Grinder #505404, JAT-404 #505407, JAT-407 JAT-407 JAT-404 Operation & Parts Manual M-505404 Edition 2 06/2015 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2015 JET...
-
Page 2: Warranty And Service
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. -
Page 3: Safety Warnings
10. The air tool must be properly lubricated before operating. Do not use this tool for other than its intended use. If used for other purposes, JET disclaims 11. Never start a percussion type air tool (chipper, any real or implied warranty and holds itself breaker, buster, etc.) without securing the... - Page 4 33. Do not lubricate the tool with combustible or storing tool. liquids, such as kerosene, diesel or jet fuel. 23. Make sure tool is switched off, and your finger 34. Do not dispose of this tool with normal off the trigger, before connecting to air supply.
-
Page 5: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
Do not use detergent oil. Re-connect air. Run die grinder at low throttle without load for a few seconds to Figure 1 (JAT-404 shown) distribute the oil throughout tool. Loosen collet nut using the two wrenches on... - Page 8 Use a light oil containing rust inhibitors, such as If the air tool is not performing according to SAE #10. Many JET air tools have integral oil specifications, the following are among the most reservoirs, which should be kept filled when in-line common causes.
- Page 9 Figure 2 Recommended arrangement of air piping and air line system ...
- Page 10 Troubleshooting JAT-404/407 Die Grinders Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
-
Page 11: Replacement Parts
Replacement parts Service parts are listed on the following pages. To order parts or reach our service department, call 1-800- 274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately. ... - Page 12 #505404, JAT-404, Die Grinder – exploded view JAT-404,407 Die Grinders ...
- Page 13 #505404, JAT-404, Die Grinder – parts list Index Part No. Description Index Part No. Description JAT404-01 Motor housing 21 JSM5130-21 Deflector SM-30102 Spring pin 3x24L 22 51222 Spindle JSM5130-03 Air inlet 23 JAT404-23 Clamp nut JSM5130-04 Throttle lever 24 51224 Collet 1/4in.
- Page 14 #505407, JAT-407, Extended Die Grinder – exploded view JAT-404,407 Die Grinders ...
- Page 15 #505407, JAT-407, Extended Die Grinder – parts list Index Part No. Description Index Part No. Description JAT404-01 Motor housing 22 51222 Spindle SM-30102 Spring pin 3x24L 23 51223F Lock nut JSM5130-03 Air inlet 24 51224 Collet 1/4in. JSM5130-04 Throttle lever 25 51225 Collet nut Throttle lever assembly (incl.
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-404,407 Die Grinders ...