System Configuration - Toshiba MMD-VNK802HEXE Owner's Manual

9-EN
Air to Air Heat Exchanger with DX Coil Unit
3

System Configuration

The control method of this product differs depending on the system configuration. Operate it following the methods
explained in the system configuration examples below.
• For the actual system configuration, ask your dealer or the installer of the product for information.
• Refer also to the installation manuals and owner's manuals of the remote controllers.
• If a central remote controller is used, refer also to its installation manual and owner's Manual.
System example
A. Air to Air Heat Exchanger with DX Coil Unit system
Outdoor unit
Air to Air Heat Air to Air Heat Air to Air Heat
Exchanger with
Exchanger with Exchanger with
DX Coil Unit DX Coil Unit DX Coil Unit
Remote controller NRC-
01HE/RBC-AMT32E
B. Air to Air Heat Exchanger with DX Coil Unit system linked with
air conditioners
Outdoor unit
Air Air Air to Air Heat
conditioner Exchanger with
conditioner
DX Coil Unit
Remote controller NRC-
01HE/RBC-AMT32E
Operation
The remote controller can be used to If two remote controllers
ON/OFF running the Air to Air Heat are used, the latter
Exchanger with DX Coil Unit. operation overrides the
former and their indications
always reflect the result of
Remote controller for the Air to Air
the latter operation.
Heat Exchanger with DX Coil Unit
(NRC-01HE)
The remote controller can be used to
select the operation mode, start and
stop the unit, control the ventilation
FAN speed, select the ventilation
Air to Air Heat
mode, and adjust the temperature.
Exchanger with
DX Coil Unit
Main remote controller (RBC-
AMT32E)
• The remote controller can be used to
select the operation mode, start and
stop the unit, and adjust the
temperature.
• The remote controller cannot be
used to change the ventilation FAN
speed or select ventilation mode.
The remote controller can be used to If two remote controllers
ON/OFF running the Air to Air Heat are used, the latter
Exchanger with DX Coil Unit. operation overrides the
former and their indications
always reflect the result of
Remote controller for the Air to Air
the latter operation.
Heat Exchanger with DX Coil Unit
(NRC-01HE)
The remote controller can be used to
select the operation mode, start and
stop the unit, control the ventilation
FAN speed, select the ventilation
mode, and adjust the temperature.
Air to Air Heat
Exchanger with
DX Coil Unit
Main remote controller (RBC-
AMT32E)
• The remote controller can be used to
select the operation mode, start and
stop the unit, and adjust the
temperature.
• The remote controller cannot be
used to change the ventilation FAN
speed or select the ventilation mode.
* The remote controller (NRC-01HE)
can be used to start and stop only
the Air to Air Heat Exchanger with
DX Coil Unit. For this operation, it is
necessary to change the settings.
Consult the dealer for details.
– 5 –
Owner's Manual
Air to Air Heat Exchanger with DX Coil Unit
C. Central control system
(When controlling the Air conditioner and the Air to Air Heat
Exchanger with DX Coil Unit separately)
Outdoor unit
Note
Air
conditioner
Remote controller NRC-
01HE/RBC-AMT32E
D. Central control system
(When controlling the Air conditioner and the Air to Air Heat
Exchanger with DX Coil Unit together)
Outdoor unit
Air
conditioner
Remote controller
NRC-01HE/RBC-
AMT32E
* When the Air to Air Heat Exchanger with DX Coil Unit system linked with indoor air conditioners is used, set the
Air to Air Heat Exchanger with DX Coil Unit as "Follower", referring to "Setting the address manually using the
remote controller" in the Installation Manual of the outdoor unit.
System example
The central controller can be used to
ON/OFF the whole system and
separately ON/OFF groups of Air
conditioners and the Air to Air Heat
Exchanger with DX Coil Units.
Central controller for 64/128 units/
The central controller cannot be used
groups
to control the ventilation FAN speed or
TCB-SC642TLE2, BMS-CM1280TLE
select the ventilation mode of the Air to
Air Heat Exchanger with DX Coil Unit.
* Use NRC-01HE or RBC-AMT32E to
control only the group of the Air to
Air Heat Exchanger with DX Coil
Air Air to Air Heat
Air to Air Heat
Unit. You cannot control the
conditioner Exchanger with
Exchanger with
ventilation FAN speed or select the
DX Coil Unit
DX Coil Unit
ventilation mode when using RBC-
AMT32E.
Remote controller NRC-
01HE/RBC-AMT32E
The central controller can be used to
ON/OFF the whole system.
The central controller cannot be used
to control the ventilation FAN speed or
Central controller for 64/128 units/ select the ventilation mode of the Air to
groups Air Heat Exchanger with DX Coil Unit.
TCB-SC642TLE2, BMS-CM1280TLE
The remote controller (NRC-01HE)
can be used to control the ventilation
FAN speed and select the ventilation
mode of the Air to Air Heat Exchanger
with DX Coil Unit.
The remote controller (RBC-AMT32E)
Air Air to Air Heat Air to Air Heat
cannot be used to control the
conditioner Exchanger with Exchanger with
ventilation FAN speed or select the
DX Coil Unit DX Coil Unit
ventilation mode of the Air to Air Heat
Exchanger with DX Coil Unit.
* The remote controller (NRC-01HE)
can be used to start and stop only
the Air to Air Heat Exchanger with
DX Coil Unit. For this operation, it is
necessary to change the settings.
Remote controller
Consult the dealer for details.
NRC-01HE/RBC-
AMT32E
10-EN
Owner's Manual
Operation Note
If two control devices are
used; the central controller
and the remote controllers
for the Air to Air Heat
Exchanger with DX Coil
Unit and Air conditioner,
the latter operation
overrides the former
regardless of which device
is used.