Related Manuals for QNAP Turbo NAS TS-EC2480U-E3-4GE-R2
Summary of Contents for QNAP Turbo NAS TS-EC2480U-E3-4GE-R2
- Page 1 QNAP Turbo NAS TS- ECx80 Series Hardware User Manual © 2014. QNAP Systems, Inc. All Rights Reserved.
- Page 2 Thank you for choosing QNAP products! This user manual provides description of the hardware of the Turbo NAS and relevant guideline of certain functions. Please read carefully and strictly adhere to the instructions of the manual. This user manual is applicable to the following Turbo NAS models:...
- Page 3 DISCLAIMER In no event shall QNAP Systems, Inc. (QNAP) liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, its accompanying software, or its documentation. QNAP makes no...
- Page 4 Regulatory Notice FCC Notice The QNAP NAS complies with different FCC compliance classes. Please refer to 0 for details. Once the class of the device is determined, refer to the following corresponding statement. ======================================================= FCC Class A Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference.
- Page 5 Modifications: Any modifications made to this device that are not approved by QNAP Systems, Inc. may void the authority granted to the user by the FCC to operate this equipment. CE NOTICE The QNAP NAS complies with different CE compliance classes. Please refer to 0 for details.
- Page 6 Symbols in this document This icon indicates the instructions must be strictly followed. Failure to do so could result in injury to human body or death. Warning This icon indicates the action may lead to disk clearance or loss OR failure to follow the instructions could result in data damage, disk Caution damage, or product damage.
-
Page 7: Table Of Contents
USB One Touch Copy ..............13 Chapter 4. LED and Alarm Buzzer Specifications ........... 14 Chapter 5. Upgrade Memory on QNAP Turbo NAS (RAM Module Installation) 17 TS-EC2480U-RP, TS-EC1680U-RP, TS-EC1280U-RP, TS-EC880U-RP ....17 TS-EC880 P , TS-EC1080 P ..............20 Chapter 6. -
Page 8: Safety Warnings
Safety Warnings The NAS can operate normally in temperatures of 0ºC–40ºC (32ºF -104ºF) and relative humidity of 5%–95%. Please make sure the environment is well-ventilated. The power cord and devices connected to the NAS must provide correct supply voltage (100W, 90–264V). Do not place the NAS in direct sunlight or near chemicals. -
Page 9: Chapter 1. Cpu And Memory Specifications
Caution: Modifying the hardware, software, or firmware of the QNAP products will void the warranty. QNAP is not responsible for any form of damage or loss of data caused by modding the QNAP products. Users should bear their own risks of all sorts of possible data loss or system instabilities due to changing the hardware parts, modifying the default system firmware or installing any unauthorized third party applications on QNAP products. - Page 10 System TS-EC1280U-RP TS-EC1680U-RP TS-EC2480U-RP Quad-Core Intel Xeon Quad-Core Intel Xeon Quad-Core Intel Xeon Processor E3-1200 v3 Processor E3-1200 v3 Processor E3-1200 v3 Family Family Family Memory 4GB DDR3 ECC RAM 4GB DDR3 ECC RAM 4GB DDR3 ECC RAM Flash 512MB (USB DOM) 512MB (USB DOM) 512MB (USB DOM) CPU replaceable...
-
Page 11: Chapter 2. Power Button And Reset Button Behavior
LCD panel password: (blank)* VLAN will be disabled. Service binding: All the NAS services run on all available network interfaces. *This feature is only provided by the NAS models with LCD panels. Please visit http://www.qnap.com for details. - Page 12 Advanced system reset (10 sec) Press the reset button for 10 seconds; you will hear two beeps at the third and the tenth seconds. The NAS will reset all the system settings to default as it does by web-based system reset in “Control Panel” > “System Settings” > “Backup / Restore” > “Restore to Factory Default”...
-
Page 13: Chapter 3. Usb One Touch Copy
Chapter 3. USB One Touch Copy This feature is only provided by the NAS models with a USB One Touch Copy button. Please visit http://www.qnap.com for details. Number of seconds (press the one touch copy button System to trigger data copy) All NAS models 0.5 sec... -
Page 14: Chapter 4. Led And Alarm Buzzer Specifications
Chapter 4. LED and Alarm Buzzer Specifications The LED indicators of the NAS indicate the system status and information. When the NAS is turned on, check the following items to make sure the system status is normal. Note that the following LED information is applicable only when users have properly installed the hard drive, and connected the NAS to the network and the power supply. - Page 15 Color LED Status Description The disk data is being accessed from the Orange network and a read/write error occurs during the process. Orange Flashes The NAS is connected to the network. orange The 10GbE network expansion card is Green installed. 10 GbE Green No 10GbE network expansion card is installed.
- Page 16 Beep alarm: All NAS models The beep alarm can be disabled in “Control Panel” > “System Settings” > “Hardware”. Beep sound Number of Times Description The NAS is starting up. The NAS is being shut down (software shutdown). Short beep (0.5 sec) The user presses the reset button to reset the NAS.
-
Page 17: Chapter 5. Upgrade Memory On Qnap Turbo Nas (Ram Module Installation)
QNAP provides RAM module (optional purchase) for users to upgrade the memory of the NAS. Insert an extra RAM module on the motherboard of the NAS to upgrade the memory. - Page 18 Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other connectors or cables from the NAS. Before installing the network expansion card, put on an antistatic wrist strap to prevent electrostatic discharge. The crocodile clip should be connected to the ground. Loosen the 2 screws on the rear of the NAS as shown in the illustration.
- Page 19 Release the ejector clips gently by pulling them out of the sides of the RAM slot. Grasp the edge of the RAM module. Align the notch on the gold edge of the RAM module with the notch in the RAM slot. Insert the RAM module to the RAM slot until it cannot go any further.
-
Page 20: Ts-Ec880 Pro, Ts-Ec1080 Pro
TS-EC880 Pro, TS-EC1080 Pro Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other connectors or cables from the NAS. Before installing the network expansion card, put on an antistatic wrist strap to prevent electrostatic discharge. The crocodile clip should be connected to the ground. - Page 21 Remove the case cover of the NAS gently. Loosen the cable...
- Page 22 Release the ejector clips gently by pulling them out of the sides of the RAM slot. Grasp the edge of the RAM module. Align the notch on the gold edge of the RAM module with the notch in the RAM slot. Insert the RAM module to the RAM slot until it cannot go any further.
-
Page 23: Chapter 6. Network Expansion Card Installation
Chapter 6. Network Expansion Card Installation Warning: The following instructions should only be performed by an authorized and trained technician. Strictly adhere to the instructions to install a network expansion card on the NAS. Failure to do so could result in injury to human body or death. The TS-x80 series provides expansion slots for network expansion. - Page 24 Network Expansion Card Compatibility Bracket A (X520-T2) Intel® Ethernet Server Adapter X520-T2 (E10G42B) Bracket B 1. Intel® Ethernet Server Adapter X520-SR2 (X520-SR2/X520-DA2) (E10G42BFSR) 2. Intel® Ethernet Server Adapter X520-DA2 (E10G42BTDA) Bracket C (Emulex) 1. Emulex OneConnect 10GbE Network Adapters, SFP+ Direct attach copper (OCe11102-NX) 2.
- Page 25 Remove the case cover of the NAS gently. Loosen the screws and remove the expansion slot cover.
- Page 26 Grasp the edge of the network expansion card. Align the notch on the gold edge of the card with the notch in the PCIe slot. Insert the network expansion card to the PCIe slot until it cannot go any further. Fasten the screws.
-
Page 27: Ts-Ec2480U-Rp, Ts-Ec1680U-Rp, Ts-Ec1280U-Rp, Ts-Ec880U-Rp
TS-EC2480U-RP, TS-EC1680U-RP, TS-EC1280U-RP, TS-EC880U-RP Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other connectors or cables from the NAS. Before installing the network expansion card, put on an antistatic wrist strap to prevent electrostatic discharge. The crocodile clip should be connected to the ground. Loosen the 2 screws on the rear of the NAS as shown in the illustration. - Page 28 Loosen the screw and remove the expansion slot cover. Insert the network expansion card to the PCIe slot until it cannot go any further. Then fasten the screw. Push back Motherboard Drawer. Then fasten the screw. Connect the power adaptor and cables to the NAS. To check that the network expansion is recognized by the NAS, power up the NAS and login the web interface as an administrator.
-
Page 29: Chapter 7. Install An Msata Flash Module To The Nas
Chapter 7. Install an mSATA Flash module to the NAS. Warning: The following instructions should only be performed by an authorized and trained technician. Strictly adhere to the instructions to install a mSATA module on the NAS. Failure to ... - Page 30 Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other connectors or cables from the NAS. Loosen the 2 screws on the rear of the NAS as shown in the illustration. Hold the handle and pull backwards to remove the Motherboard Drawer.
- Page 31 Carefully grasp the edge of the mSATA Flash Module. Align the notch on the gold edge of the mSATA module with the notch in the mSATA slot. Insert the mSATA Flash Module to the mSATA slot until it cannot go any further. Insert the module fixing Return the Motherboard Drawer to its normal position.
- Page 32 To check that the mSATA Flash Module is recognized by the NAS, power up the NAS and login to the web interface as an administrator. Go to “Control Panel” > “Storage Manager” > “Disk” and check the “Internal Cache Port”.
-
Page 33: Ts-Ec880 Pro, Ts-Ec1080 Pro
TS-EC880 Pro, TS-EC1080 Pro Turn off the NAS. Disconnect the power adaptor, network cable(s), and any other connectors or cables from the NAS. Before installing the network expansion card, put on an antistatic wrist strap to prevent electrostatic discharge. The crocodile clip should be connected to a grounded surface. - Page 34 Carefully grasp the edge of the mSATA Flash Module. Align the notch on the gold edge of the mSATA Flash Module with the notch in the mSATA slot. Insert the mSATA Flash Module to the mSATA slot until it cannot go any further. Insert and fasten screws in place as indicated.
- Page 35 Close the case cover and fasten the screws. Connect the power adaptor and cables to the NAS. To check that the mSATA Flash Module is recognized by the NAS, power up the NAS and login to the web interface as an administrator. Go to “Control Panel” > “Storage Manager”...
-
Page 36: Chapter 8. Hot-Swap Hard Drives
Chapter 8. Hot-swap Hard Drives The QNAP NAS is compatible with 2.5-inch/3.5-inch SATA hard drives from major hard drive brands. For the updated hard drive compatibility list, please visit http://www.qnap.com. Caution: QNAP disclaims any responsibility for product damage/malfunction or data loss/recovery due to misuse or improper installation of hard disks in any occasions for any reasons. - Page 37 The NAS supports hot-swapping the hard drives when 1 member drive crashes in RAID 1 or 1–2 member drives crash in RAID 5 or RAID 6. Follow the steps below to hot-swap the hard drive when a member drive fails in a RAID configuration. 1.
-
Page 38: Chapter 9. Raid Recovery
Chapter 9. RAID Recovery The QNAP NAS supports recovery of a failed RAID group from unintentional disconnection or removal of the hard drives from the system. Users can recover an inactive RAID 1, RAID 5, or RAID 6 group to degraded mode, or an inactive RAID 0 and JBOD configuration to normal. - Page 39 Standard QNAP RAID 5 Standard QNAP RAID 6 RAID 5 RAID 6 Degraded mode N-1 & N-2 N-1 & N-2 Read only N-1, bad blocks N-2, bad blocks protection (for found in the found in the immediate data surviving drives of surviving drives of backup &...
-
Page 40: Chapter 10. Use The Lcd Panel
Chapter 10. Use the LCD Panel This feature is only provided by the NAS models with LCD panels. Please visit http://www.qnap.com for details. The NAS provides a handy LCD panel for users to perform disk configuration and view the system information. - Page 41 For example, when 5 hard drives installed are available on the NAS, the LCD panel shows: → R Press the “Select” button to browse more options, for example, RAID 6. Press the “Enter” button and the following message shows. Press the “Select” button to select “Yes”...
- Page 42 Note: The data encryption functions may not be available in accordance to the legislative restrictions of some countries. View system information by the LCD panel When the LCD panel shows the server name and IP address, press the “Enter” button to enter the Main Menu.
- Page 43 2. Physical disk The following options are available: Disk Info Back to Main Menu The disk info shows the temperature and the capacity of the hard drive. ° 3. Volume This section shows the disk configuration of the NAS. The first line shows the RAID configuration and storage capacity;...
- Page 44 6. Reboot Use this option to restart the NAS. Press the “Select” button to select “Yes”. Then press the “Enter” button to confirm. 7. Password The default password of the LCD panel is blank. Enter this option to change the password of the LCD panel.
- Page 45 System Messages When the NAS encounters a system error, an error message will be shown on the LCD panel. Press the “Enter” button to view the message. Press the “Enter” button again to view the next message. System Message Description Sys.
-
Page 46: Chapter 11. Install Power Supply Unit
Chapter 11. Install Power Supply Unit Note: The following instructions should only be performed by an authorized and trained technician. To replace a failed power supply unit on the TS-EC2480U-RP, TS-EC1680U-RP, TS-EC1280U-RP, TS-EC880U-RP Turbo NAS Turbo NAS, follow the steps below. Turn off the NAS. - Page 47 Unplug the failed power supply. Plug in a new power supply to the NAS. Turn on the NAS. Connect the power adaptor and cables to the NAS.
- Page 48 Enable warning alert for redundant power supply on the web-based interface: If two power supply units (PSU) have been installed on the NAS and connected to the power sockets, both PSU will supply the power to the NAS (applied to 1U and 2U models). Users can enable redundant power supply mode in “Control Panel”...
-
Page 49: Technical Support
Technical Support QNAP provides dedicated online support and customer service via instant messenger. Online Support: http://www.qnap.com Forum: http://forum.qnap.com Technical Support in the USA and Canada: Email: q_supportus@qnap.com TEL: +1-909-595-2782 Address: 168 University Parkway, Pomona CA 91768 Service Hours: 08:00-17:00 (GMT- 08:00 Pacific Time, Monday to Friday) -
Page 50: Product Compliance Class
Product Compliance Class NAS Models TS-EC2480U-RP Class A Class A TS-EC1680U-RP Class A Class A TS-EC1280U-RP Class A Class A TS-EC880U-RP Class A Class A TS-EC1080 Pro Class B Class B TS-EC880 Pro Class B Class B... -
Page 51: Gnu General Public License
GNU GENERAL PUBLIC LICENSE Version 3, 29 June 2007 Copyright © 2007 Free Software Foundation, Inc. <http://fsf.org/> Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. Preamble The GNU General Public License is a free, copyleft license for software and other kinds of works. - Page 52 distribute and/or modify it. For the developers' and authors' protection, the GPL clearly explains that there is no warranty for this free software. For both users' and authors' sake, the GPL requires that modified versions be marked as changed, so that their problems will not be attributed erroneously to authors of previous versions.
- Page 53 A “covered work” means either the unmodified Program or a work based on the Program. To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under applicable copyright law, except executing it on a computer or modifying a private copy.
- Page 54 needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to control those activities. However, it does not include the work's System Libraries, or general-purpose tools or generally available free programs which are used unmodified in performing those activities but which are not part of the work.
- Page 55 measures. When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention is effected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modification of the work as a means of enforcing, against the work's users, your or third parties' legal rights to forbid circumvention of technological measures.
- Page 56 by their nature extensions of the covered work, and which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate” if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation's users beyond what the individual works permit.
- Page 57 A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be included in conveying the object code work. A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or household purposes, or (2) anything designed or sold for incorporation into a dwelling.
- Page 58 Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented (and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or copying.
- Page 59 All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that term.
- Page 60 You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than this License grants you permission to propagate or modify any covered work.
- Page 61 the right to grant patent sublicenses in a manner consistent with the requirements of this License. Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor's essential patent claims, to make, use, sell, offer for sale, import and otherwise run, modify and propagate the contents of its contributor version.
- Page 62 copies), or (b) primarily for and in connection with specific products or compilations that contain the covered work, unless you entered into that arrangement, or that patent license was granted, prior to 28 March 2007. Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be available to you under applicable patent law.
- Page 63 If the Program specifies that a proxy can decide which future versions of the GNU General Public License can be used, that proxy's public statement of acceptance of a version permanently authorizes you to choose that version for the Program. Later license versions may give you additional or different permissions.
Need help?
Do you have a question about the Turbo NAS TS-EC2480U-E3-4GE-R2 and is the answer not in the manual?
Questions and answers