Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Santec Manuals
  4. Plumbing Product
  5. Barosa 2429MC
  6. Installation instruction

Santec Barosa 2429MC Installation Instruction

Wall mount widespread lavatory set
Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
Please read the instructions completely before beginning the installation.
Barosa Collection
Model Number: 2429MC
Flush both supply lines before installation, then shut off both supply lines.
Minimum hole size for the spout and handle trim is 1-1/4" and maximum of 1-1/2"
ROUGH INSTALLATION
- Determine where the finished wall will be. This measurement is
1
necessary to accurately plumb in the valve.
- Install the valve making sure that the measurement between the
center of the valve inlet and the outside of the finish wall is 2-3/4". This
measurement is called the backset.
- Using 1/2" IPS, connect the corner of the valves to the spout
2
base at the desired spread.
- Again, allow no more than 1-1/4" diameter holes for the spout and
handles.
NOTE:
- Where tile construction is planned for the finished walls, allow for
extra thickness dimensions when roughing in the valves.
- Test for proper function before closing walls.
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
Installation Instruction
BAROSA COLLECTION
Wall Mount Widespread Lavatory Set
Backset
Finished Wall
Center of Valve Inlet
Rev 06/2016
1/6

Advertisement

loading

Related Manuals for Santec Barosa 2429MC

Summary of Contents for Santec Barosa 2429MC

  • Page 1 Rev 06/2016 Installation Instruction BAROSA COLLECTION Wall Mount Widespread Lavatory Set Please read the instructions completely before beginning the installation. Barosa Collection Model Number: 2429MC Flush both supply lines before installation, then shut off both supply lines. Minimum hole size for the spout and handle trim is 1-1/4” and maximum of 1-1/2” ROUGH INSTALLATION - Determine where the finished wall will be.

  • Page 2: Spout Installation

    SPOUT INSTALLATION - Wrap the pipe threading for the spout with teflon tape. Then, thread the spout onto the pipe until it is secured with the spout facing downward. NOTE: The length of threaded pipe coming out from the finish wall should be no longer than 1/2”.

  • Page 3: Parts Drawing

    PARTS DRAWING PART DESCRIPTION PART # PART DESCRIPTION PART # Teflon Washer PM-099 Barosa WM WS handle flange PH00149 Stem Extension SA240 Barosa Wall Mount Tub Filler Spout Flange PH00150 Belleville Washer PM-184 Barosa Wall Mount WS Spout PS-6MC00-U-1 Screw #6-32 x 1-1/4" PM-179 Valve Extension PM-1111...

  • Page 4: Specification Sheet

    SPECIFICATION SHEET 8 " 2 " 8 " 4 " 8 " 2 " POP-UP Ø 2 " " " 12" Ø 1 " The measurements shown are for reference only. Products and specifications shown are subject to change without notice. www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681...

  • Page 5: To Obtain Warranty Service

    Doing so may ruin your faucet finish and/or void the warranty. Thank you for making SANTEC a part of your lifestyle and luxury spa experience. Our products have been created as works of enduring quality and sophisticated design.

  • Page 6: Lifetime Limited Warranty

    SANTEC reserves the product components of the covered product will be repaired, refinished, or replaced at the sole discretion of SANTEC. SANTEC reserves the right to examine any product claimed defective prior to any warranty claim being accepted or processed, at its sole discretion. This warranty gives you specific legal rights and you may have other rights which may vary from state to state.