Software License; Laser Information - Sharp MX-B200 Start Manual

CAUTIONS
Each instruction also covers the optional units used with this product.
Caution label on the unit
The label ( , ) in the fusing area of the unit indicates the following:
: Caution, risk of danger
: Caution, hot surface
Cautions on using
Follow the cautions below when using this unit.
Warning:
• The fusing area is hot. Exercise care in this area when removing misfed
paper.
• Do not look directly at the light source. Doing so may damage your eyes.
Caution:
• Place the unit on a firm, level surface.
• Do not install the unit in a humid or dusty location.
• When the unit is not used for a long time, for example during prolonged
holidays, turn the power switch off and remove the power cord from the outlet.
• When moving the unit, be sure to turn the power switch off and remove the
power cord from the outlet.
• Do not switch the unit rapidly on and off. After turning the unit off, wait 10
to 15 seconds before turning it back on.
• Do not cover the unit with a dust cover, cloth or plastic film while the power
is on. Doing so may prevent heat radiation, damaging the unit.
• Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
• The socket-outlet shall be installed near the machine and shall be easily
accessible.
Important points when selecting an installation site
Do not install your unit in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity changes, e.g., near an air
conditioner or heater.
Be sure to allow the required space
around the machine for servicing
and proper ventilation.
Cautions on handling
Be careful in handling the unit as
follows to maintain the performance of
this unit.
Do not drop the unit, subject it to shock or strike it against any object.
Store spare toner cartridges in a cool dry place without removing from
the package before use.
• If they are exposed to direct sunlight or excessive heat, poor copies may
result.
Do not touch the photoconductive drum (green portion).
• Scratches or smudges on the drum will cause dirty copies.
Proper storage
Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight
Store paper in the wrapper and lying flat.
• Paper stored out of the wrapper or in packages standing on end may curl
or get damp, resulting in paper misfeeds.
CAUTION:
Do not install the machine in a location with poor air circulation.
A small amount of ozone is created inside the machine during printing. The
amount of ozone created is not sufficient to be harmful; however, an
unpleasant odor may be noticed during large copy runs, and thus the machine
should be installed in a room with a ventilation fan or windows that provide
sufficient air circulation. (The odor may occasionally cause headaches.)
* Install the machine so that people are not directly exposed to exhaust from
the machine. If installed near a window, ensure that the machine is not
exposed to direct sunlight.
Supply and Consumables
The supply of spare parts for a repair of the appliance is guaranteed for at least
7 years following the termination of production. Spare parts are those parts of
the apparatus which may break down within the scope of ordinary use of the
product, whereas those parts which normally exceed the life of the product are
not considered spare parts. Consumables also, are available for 7 years
following the termination of production.
MSDS (Material Safety Data Sheet)
The MSDS (Material Safety Data Sheet) can be viewed at the following URL
address: http://www.sharp-world.com/corporate/info/index.html
4
20 cm
10 cm 10 cm
In some areas, the "POWER" switch positions are marked "I" and " " on
the copier instead of "ON" and "OFF".
If your copier is so marked, please read "I" for "ON" and " " for "OFF".
Caution!
For a complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall
be easily accessible.
Shielded interface cables must be used with this equipment to maintain
compliance with EMC regulations.

Laser information

780 nm+15 nm
Wave length
-10 nm
Pulse times 12.88 µs ±12.88 ns/7 mm
Output power Max 0.2 mW
At the production line, the output power of the scanner unit is adjusted to 0.18
MILLIWATT PLUS 5% and is maintained constant by the operation of the
Automatic Power Control (APC).
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition
1.2-2001)
This product is designed for commercial application only and as such it falls
outside the scope of Regulation (EC) 1275/2008 implementing EU Directive
2005/32/EC on eco-design requirements for standby and off mode electric
power consumption. Sharp does not recommend the product for domestic
application and will not accept any liability for such use.
Products that have earned the ENERGY STAR
to protect the environment through superior energy efficiency.
The products that meet the ENERGY STAR
above.
The products without the logo may not meet the ENERGY STAR

SOFTWARE LICENSE

The SOFTWARE LICENSE will appear when you install the software from the
CD-ROM. By using all or any portion of the software on the CD-ROM or in the
unit, you are agreeing to be bound by the terms of the SOFTWARE LICENSE.
Trademark acknowledgements
® ®
• Microsoft , Windows , Windows
®
Internet Explorer are registered trademarks or trademarks of Microsoft
Corporation in the U.S.A. and other countries.
® ®
• Adobe , the Adobe logo, Acrobat
registered trademarks or trademarks of Adobe Systems Incorporated in the
United States and other countries.
• IBM, PC/AT, and PowerPC are trademarks of International Business Machines
Corporation.
• Sharpdesk is a trademark of Sharp Corporation.
• All other trademarks and copyrights are the property of their respective owners.
Do not make copies of anything which is prohibited from copying by law.
The following items are normally prohibited from copying by national
law. Other items may be prohibited by local law.
Money Stamps
Bank drafts Checks
Emission density (measured according to RALUZ122: Edition
June 2006)
Measured Condition of
chemicals copier
Ozone
Dust
When copier is in
Styrene
operation
Benzene
TVOC
When on standby
®
are designed
®
guidelines carry the logo shown
®
guidelines.
® ®
2000, Windows XP, Windows Vista
® ®
, the Adobe PDF logo, and Reader
Bonds Stocks
Passports Driver's licences
Colour mode Diffusion speed
Black and white 1.5 gm/h or less
Black and white 4.0 gm/h or less
Black and white 1.0 gm/h or less
Black and white 0.05 gm/h or less
Black and white 10 gm/h or less
- 2.0 gm/h or less
®
and
TM
are