Group Scan (GS) Mode Priority Watch Busy Channel Lockout Call Tone Roger Beep Key Beep On/Off Internal Speaker Setting On/Off Mic Gain Setting Backlight Color Backlight Brightness Operation - Special Features Channel Banks 100 User programmable RX channels UNIDEN UH9000 UHF CB Transceiver...
Page 3
Search Extra Channel Range and Programme a RX Channel CTCSS Codes Table DCS Codes Table Channel Bank List - Police (POL) Channel Bank List - Fire UHF CB Channel Guidelines UHF CB Channels & Frequencies Warranty UNIDEN UH9000 UHF CB Transceiver...
Introduction The Uniden UH9000 is designed to provide you with years of trouble free service. Its rugged components and materials are capable of withstanding harsh environments. Please read this Operating Manual carefully to ensure you gain the optimum performance of the unit.
Page 5
If there is trouble with transmitting: Check that the transmission line (coaxial cable) is securely connected to the ANTENNA connector. Check that the antenna is fully extended for proper operation. Check that all transmission line (coaxial cable) connections are secure and free of corrosion. UNIDEN UH9000 UHF CB Transceiver...
(MK900) DC Power Cord Removable Bracket & with fuse Washer Stars And Screws Screws Optional Accessories Visit the UH9000 page on the website for more information on the availability of optional accessories: www.uniden.com.au for Australia UNIDEN UH9000 UHF CB Transceiver...
Disconnecting the MIC from the MIC Jack screwdriver or similar object carefully push the lock tab of the MIC plug towards the MIC cord and at the same time tug on the MIC cord to draw back the MIC plug. UNIDEN UH9000 UHF CB Transceiver...
Conventional Mounting with Double Sided Tape (not supplied) High quality Double-Sided tape can be found at good retail stores. Secure the front and back pieces of the MIC Hanger using the supplied binding screws. Locate a suitable mounting position. UNIDEN UH9000 UHF CB Transceiver...
Align the guide rails along the side of the base and insert them into the slots provided. Then use the screws to lock them securely in position. BASE unit with secured guide rails. UNIDEN UH9000 UHF CB Transceiver...
Page 13
Slide Mount Bracket Slide the bracket along the guide rails to attach the bracket to the unit. Over the BASE unit Under the BASE unit UNIDEN UH9000 UHF CB Transceiver...
The UH9000 can operate on 12VDC (13.8V) or 24VDC (27.6V) power and HI NOTE covered by the manufacturer’s warranty. The power turns off automatically if voltage falls below 9.0VDC. locating the cause of the power supply problem. UNIDEN UH9000 UHF CB Transceiver...
Setting the Squelch Level Press Turn the rotary knob or press to select the desired squelch level. If a button is not pressed within 10 seconds the UHF CB Radio will automatically exit the Menu Mode. NOTE UNIDEN UH9000 UHF CB Transceiver...
Then carefully turn through. the rotary knob clockwise until the noise fades. Now only strong signals get through. Monitor Press and hold the squelch and receive all weak signals. Press and hold again to cancel. UNIDEN UH9000 UHF CB Transceiver...
34 - page 40. NOTE Smart-Key Function The smart key [S] provides one touch access to one of these functions; Instant Press and hold [S] to change the SMART key function between the three options. UNIDEN UH9000 UHF CB Transceiver...
2. Turn the rotary knob at the base or press on the microphone to select the desired channel. 3. Press and hold to save and exit. Recalling the Instant Channel Press [S] when Smart Key is set to Instant Channel function. UNIDEN UH9000 UHF CB Transceiver...
Emergency Calls. Select the desired channel. Press the microphone’s [PTT] button and speak normally into the microphone. Hold it approx. 7cm from your mouth. Release [PTT] to end the transmission and listen for a reply. UNIDEN UH9000 UHF CB Transceiver...
Select desired channel. 1. Press 2. Turn the rotary knob or press on the microphone to change the setting 3. Press and hold to save & exit from the menu mode. NOTE UNIDEN UH9000 UHF CB Transceiver...
CH02 on Duplex Mode will Receive on CH02 but Transmit on CH32 etc... If you transmit on CH01 Duplex mode, you are actually transmitting on CH31 the repeater station down-converts your signal and retransmits on CH01. Operation with the aid of a Repeater Station (Duplex). UNIDEN UH9000 UHF CB Transceiver...
41 - 48). 3. Press to store the setting. 4. Press and hold to save & exit the menu mode. Only channels 01 - 08 and 41 - 48 are available for Duplex. NOTE UNIDEN UH9000 UHF CB Transceiver...
Select the channel you want to store. Press and hold or [SCAN/MEM] button on the microphone to store. The icon appears and a short tone is heard. or [SCAN/MEM] button on the microphone once more. The icon disappears. UNIDEN UH9000 UHF CB Transceiver...
P-: Master Scan is ON with the current GS channel memory. Open/Group Scan is disabled. P1: Master Scan is ON with loading CH09-20 in GS. P3: Master Scan is ON with loading CH49-60 in GS. UNIDEN UH9000 UHF CB Transceiver...
To select OS Scan Mode: 1. Press 2. Turn the rotary knob or press press to save scan type setting. 3. Press and hold to save and exit from the Menu mode. UNIDEN UH9000 UHF CB Transceiver...
Priority Channel for activity while listening to the active one. To select GS Scan Mode: 1. Press 2. Turn the rotary knob or press press to save scan type setting. 3. Press and hold to save and exit from the Menu mode. UNIDEN UH9000 UHF CB Transceiver...
This is particularly important when using CTCSS/DCS. 1. Press 2. Turn the rotary knob or press on the microphone to change the setting between ON or OFF. 3. Press and hold to save & exit from the menu mode. UNIDEN UH9000 UHF CB Transceiver...
1. Press 15 times. The BEEP 2. Turn the rotary knob or press on the microphone to change the 3. Press and hold to save & exit from the menu mode. UNIDEN UH9000 UNIDEN UH9000 UHF CB Transceiver UHF CB Transceiver...
2. Turn the rotary knob or press on the microphone to select the color from CLEAR/ BLUE / RED / PURPLE/ GREEN / CYAN / YELLOW. 3. Press and hold to save & exit from the menu mode. UNIDEN UH9000 UHF CB Transceiver...
Operation Backlight Brightness 1. Press 19 times 2. Turn the rotary knob or press on the microphone to change the setting between 3. Press and hold to save & exit from the menu mode. UNIDEN UH9000 UHF CB Transceiver...
The channel banks can be selected as follows; 3. Press and hold to save and exit menu mode. 12.5kHz steps. NOTE frequencies and guidelines for their use is printed on page 34 - page 40. UNIDEN UH9000 UHF CB Transceiver...
When desired frequency is entered press the rotary knob to move to Alpha tag selection. to shift between cursor positions. If you do not wish to name the channel then skip this step. next channel if desired. Press [PTT] on the microphone to exit programming mode. UNIDEN UH9000 UHF CB Transceiver...
If you do not wish to name the channel then skip this step. next channel if desired. Press [PTT] on the microphone to exit programming mode. UNIDEN UH9000 UHF CB Transceiver...
The above situations are not a fault of the radio but a symptom of mixed wideband and narrowband radios in current use. It is expected that as older wideband radios are phased out this issue will be eliminated. UNIDEN UH9000 UHF CB Transceiver...
UNIDEN UH9000 UHF CB Transceiver IMPORTANT: Satisfactory evidence of the original purchase is required for warranty service Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below. Warrantor: Terms of Warranty: Uniden Aust warrants to the original retail purchaser only that the UH9000 UHF CB Transceiver exclusions set out below.
Page 42
Procedure for obtaining warranty service: Depending on the country in which the original purchase (such as a legible copy of the sales docket) to Uniden. Please refer to the Uniden website for the address details. You should contact Uniden regarding any compensation that may be payable for your expenses incurred in making a warranty during warranty service.