Introduction The Uniden UH5060 is designed to provide you with years of trouble free service. Its rugged components and materials are capable of withstanding harsh environments. Please read this Operating Manual carefully to ensure you gain the optimum performance of the unit.
Page 5
PTT - Push To Talk Button DUAL - Dual Watch Button MENU/ENTER - Menu and - Select Up and Select Button Down Buttons MEM - Memory Scan Channel RJ45 type plug SCAN - Scan Button Front MIC Jack Cover OS/GS - Open Scan/Group Scan MICROPHONE UNIDEN UH5060 UHF CB Transceiver...
Owner’s Manual Microphone Hanger Microphone with screws, washers (RM500) Extension Cable Mounting Bracket with DC Power Cord mounting screws with fuse Optional Accessories: • UHF Antenna • External Speaker Visit the UH5060 page on the website for more information on the availability of optional accessories; www.uniden.com.au for Australia UNIDEN UH5060 UHF CB Transceiver...
Pull back the rubber cover and move it down along the cord. Using the flat blade of a screwdriver or similar object carefully push the lock tab of the MIC plug towards the MIC cord and at the same time tug on the MIC cord to draw back the MIC plug. UNIDEN UH5060 UHF CB Transceiver...
MIC hanger will determine which parts to use. Conventional Mounting with Screws Use the front part of the MIC Hanger only. Locate a suitable mounting position and mark and drill two 3mm holes. Fix the MIC Hanger into place with screws. UNIDEN UH5060 UHF CB Transceiver...
Page 10
MIC Hanger mounted over MIC Cable The curly cord of the Remote SPK/MIC can extend up to 1.5m. For practical installation of the MIC Hanger mounted NOTE over MIC Cable use this method with the Extension Cable. UNIDEN UH5060 UHF CB Transceiver...
Page 11
2. Drill a 13mm hole at the MIC hanger location. 3. Thread the microphone plug through the hole and connect with the extension cable. 4. Mount the MIC Hanger over the hole and cable. 5. At the Radio: Connect the extension cable plug to the MIC Jack. Fit the rubber bushing over the MIC jack. UNIDEN UH5060 UHF CB Transceiver...
NOTE If the input voltage falls below 10VDC, LO DC flashes for 5 seconds. The power turns off automatically if voltage falls below 8.5VDC. Switch your UH5060 OFF and disconnect it from the power source, before locating the cause of the power supply problem. UNIDEN UH5060 UHF CB Transceiver...
2 - med sensitivity (med squelch) 3 - min sensitivity (max/tight squelch) It requires no adjustment. 1. Press [SQL/MON]. The squelch setting flashes. 2. Press to change the setting. If tight squelch is selected SQT icon will also flash. 3. Press [MENU/ENTER] to store the setting. UNIDEN UH5060 UHF CB Transceiver...
For your reference a list of the available channels, corresponding frequencies and guidelines for their use is printed on p.27 - p.29. For Australia, Channels 05 and 35 NOTE are reserved for Emergency Calls. UNIDEN UH5060 UHF CB Transceiver...
You may select from 5 types of tones (see p.21). Current regulations require calling tones to be restricted to one transmission per minute. If a second transmission is NOTE attempted within one minute then an error tone will sound. UNIDEN UH5060 UHF CB Transceiver...
If there is a barrier that partially blocks your transmitted signal, the probability of another radio receiving the signal is very slim. Hills, tall buildings, metallic structures,...etc tend to act as a screen between radios. Standard Operation without the aid of a Repeater station. UNIDEN UH5060 UHF CB Transceiver...
ON (“ r ” for repeater channels 01 - 08 or “ n “ for repeater channels 41 - 48) or OFF (standard channel numbering). 3. Press [MENU/ENTER] to store the setting. UNIDEN UH5060 UHF CB Transceiver...
3 seconds for the signal to return, otherwise scanning resumes. After transmission in scan mode, the unit will wait 20 seconds for the signal to return, otherwise scanning resumes. To skip the active channel, press momentarily. To deactivate SCAN, press [SCAN/OS/GS]. UNIDEN UH5060 UHF CB Transceiver...
If scanning stops on a channel which is not a Priority Channel, UHF CB Radio will continue monitoring the Priority Channel for activity while listening to the active one. To deactivate SCAN, press the [SCAN/OS/GS] button. UNIDEN UH5060 UHF CB Transceiver...
- OS or GS. Select the channel you want to store. Press to [MEM] store. MEM icon appears and a short tone beep is heard. To remove the channel from SCAN memory, press [MEM] once more. The MEM icon disappears. UNIDEN UH5060 UHF CB Transceiver...
3. Press [MENU/ENTER] to store the setting. 4. Press and hold [MENU/ENTER] to save & exit from the menu mode. If a button is not pressed within 10 seconds the UHF CB Radio will automatically exit the Menu Mode. NOTE UNIDEN UH5060 UHF CB Transceiver...
CTCSS icon flashes. Press on the Remote SPK/MIC to select the desired CTCSS code 01 - 38. Press [DCS/CTCSS] once to store the new setting. To turn off CTCSS (or DCS) select the oFF code during setting. UNIDEN UH5060 UHF CB Transceiver...
1. Press [MENU/ENTER] six times. The Beep setting flashes. 2. Press to change the setting between ON or OFF. 3. Press [MENU/ENTER] to store the setting. 4. Press and hold [MENU/ENTER] to save & exit from the menu mode. UNIDEN UH5060 UHF CB Transceiver...
LCD Contrast setting flashes. 2. Press to change the setting between 01 (low contrast) to 10 (high contrast). 3. Press [MENU/ENTER] to store the setting. 4. Press and hold [MENU/ENTER] to save & exit from the menu mode. UNIDEN UH5060 UHF CB Transceiver...
The above situations are not a fault of the radio but a symptom of mixed wideband and narrowband radios in current use. It is expected that as older wideband radios are phased out this issue will be eliminated. UNIDEN UH5060 UHF CB Transceiver...
IMPORTANT: Satisfactory evidence of the original purchase is required for warranty service Please refer to our Uniden website for any details or warranty durations offered in addition to those contained below. Warrantor: The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”).
Page 31
Product, together with satisfactory evidence of your original purchase (such as a legible copy of the sales docket) to Uniden. Please refer to the Uniden website for address details. You should contact Uniden regarding any compensation that may be payable for your expenses incurred in making a warranty claim.