Related Manuals for Icop VSX-6121-FD-V2 Series
Summary of Contents for Icop VSX-6121-FD-V2 Series
- Page 1 Full 16-bit ISA Bus VSX-6121-FD-V2 DM&P Vortex86SX 300MHz Half-Size CPU Module with 2S/4USB/GPIO/FDD 128MB DDR2 Onboard User’s Manual (Revision 1.0A)
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior written permission of the ICOP Technology Inc.. ©Copyright 2007 ICOP Technology Inc.
-
Page 3: Table Of Contents
T a b l e C o n t e n t s T a b l e o f C o n t e n t s .............iii C h a p t e r 1 Introduction……………………………………………1 Packing List............1 Product Description .......... -
Page 4: Chapter 1 Introduction
C h a p t e r Introduction Packing List Product Name Package Embedded Vortex86SX CPU All-in-One Board Manual & Drivers CD x 1 RS232 cable x 1 PRINT cable x1 VSX-6121-FD-V2 IDE cable x 1 FDD cable x 1 USB cable x 2 (USB port x 2 GPIO cable x 1... -
Page 5: Product Description
Product Description The VSX-6121-FD--V2 family of low-power x86 embedded controller is designed to meet Half-Size specification with full 16-bit ISA Bus, and integrated with the following features. 300MHz Vortex86SX System-On-Chip PC/104-Plus expansion bus 128/ 256MB DDR2 system memory Meet PC/104 stacking spec. Enhanced IDE 2 watchdog timer 4 USB 2.0 (host) -
Page 6: Specifications
Specifications Features VSX-6121-FD-V2 DM&P SoC CPU Vortex86SX- 300MHz Real Time Clock with Lithium Battery Backup Cache L1:16K I-Cache, 16K D-Cache BIOS AMI BIOS Bus Interface PC/104 Standard Compliant (Optional: PCI-104) System Memory 128 /256MB DDR2 onboard Watchdog Timer Software programmable from 30.5 us to 512 seconds x2 sets(Watchdog 1 fully compatible with M6117D) Audio CM119 USB Audio Controller (Optional) - Page 7 Flash Disk Support On board 2MB SPI Flash Disk (Driver: A) 44-pin IDE Flash Disk( EmbedDisk 16MB or above) Compact Flash Type I/II (Optional) SRAM support 512KB (Optional) Power Requirement Single Voltage +5V @ 360mA Dimension 184mm X 122mm (7.24 x4.80 inches) Weight 156g Operating...
-
Page 8: Board Dimension
Board Dimension Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2... -
Page 9: Chapter 2 Installation
C h a p t e r 2 Installation Board Outline (Note1: COM2 RS232/422/485 is selected by BIOS setting) (Note2: J39 Default setting of JTAG Has to be Disable: Pin 1 & Pin 2 short) (Note3: PCI-104 connector is optional: VI/O setting: +5V) (Note4: Redundancy Signal and System-Fail-SW are optional) Vortex86SX™... -
Page 10: Connectors & Jumpers Location
Connectors & Jumpers Location Connectors Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2... - Page 11 Jumpers & LEDs Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2...
-
Page 12: Connectors & Jumpers Summary
Connectors & Jumpers Summary Summary Table Description Type of Connections Pin nbrs. 44-pin Box Header, 2.0∅ , 22x2 USB1 10-pin Box Header, 2.54∅ , 5x2 USB2 10-pin Box Header, 2.54∅ , 5x2 JTAG 6-pin Wafer, 1.25∅ , 6x1 Reset 2-pin Pin Header, 2,54∅,1x2 Redundancy (Optional) 7-pin... -
Page 13: Pin Assignments & Jumper Settings
Pin Assignments & Jumper Settings J1: IDE (44 Pins) Pin # Signal Name Pin # Signal Name IDERST IDED7 IDED8 IDED6 IDED9 IDED5 IDED10 IDED4 IDED11 IDED3 IDED12 IDED2 IDED13 IDED1 IDED14 IDED0 IDED15 IDEREQ IDEIOW IDEIOR ICHRDY IDEACK IDEINT IDESA1 IDECBLID IDESA0... - Page 14 J3: USB 2 Pin # Signal Name Pin # Signal Name LUSBD2- LUSBD3- LUSBD2+ LUSBD3+ GGND GGND J4: JTAG Pin # Signal Name Pin # Signal Name J5: RESET Pin # Signal Name Pin # Signal Name Reset J6: Redundancy (Optional) Pin # Signal Name Pin # Signal Name...
- Page 15 J8: PS/2 KBD / Mouse Pin # Signal Name Pin # Signal Name KBCLK MSCLK KBDAT MSDAT J9: COM 1 (Optional: TTL) Signal Signal Pin # Pin # Name Name DCD1 RXD1 TXD1 DTR1 DSR1 RTS1 CTS1 J10: COM2 RS232 / RS422 / RS485 (Optional: TTL) Pin # Signal Name Pin #...
- Page 16 J11: GPIO (Port 0 / Port 1) Pin # Signal Name Pin # Signal Name GP00 GP10 GP01 GP11 GP02 GP12 GP03 GP13 GP04 GP14 GP05 GP15 GP06 GP16 GP07 GP17 J12: RS485 (Auto direction) Pin # Signal Name RS485＋ RS485－...
- Page 17 J18: Power Connector (Terminal Block 5.0mm) Pin # Signal Name J20: PRINT Pin # Signal Name Pin # Signal Name STB- AFD- ERR- INIT- SLIN- ACK- BUSY SLCT Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2...
- Page 18 J22: PC104 Connector – 64pin Pin # Signal Name Signal Name IOCHCHK * RESETDRV IRQ9 DRQ2 -12V +12V IOCHRDY SMEMW * SA19 SMEMR * SA18 IOW * SA17 IOR * SA16 DACK3 * SA15 DRQ3 SA14 DACK1 * SA13 DRQ1 SA12 REFRESH * SA11...
- Page 19 J24: PC104 Connector – 40pin Pin # Signal Name Pin # Signal Name MEMCS16 * SBHE * IOCS16 * SA23 IRQ10 SA22 IRQ11 SA21 IRQ12 SA20 IRQ15 SA19 IRQ14 SA18 DACK0 * SA17 DRQ0 MEMR * DACK5 * MEMW * DRQ5 DACK6 * DRQ6...
- Page 20 J27: PC/104 + (Optional) VI/O Default setting: +5V If you need to use VI/O as +3.3V, please see the page 19. Pin # AD00 VI/O(+5V) AD02 AD01 AD05 AD04 AD03 C/BE0# AD07 AD06 AD09 AD08 AD11 VI/O(+5V) AD10 AD14 AD13 AD12 +3.3V C/BE1#...
- Page 21 Please remove the R229 and add 0 ohm (1206 type) on R230 Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2...
- Page 22 J37: LINE OUT (Optional) Pin # Signal Name LOUTR LOUTL J38: MIC-IN (Optional) Pin # Signal Name MICVREF MIC-IN J39: JTAG Disable (Default setting: Pin 1 & Pin 2 short) Pin # Signal Name Pin # Signal Name JTAG Disable J41: Console Redirection (Pin 1 &...
- Page 23 J42: FDD Pin # Signal Name Pin # Signal Name DENSEL INDEX\ MTRO\ DS1\ DS0\ MTR1\ DIR\ STEP\ TR0\ HDSEL\ DSKCHG\ Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2...
-
Page 24: System Mapping
System Mapping Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2... - Page 25 Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2...
- Page 26 Vortex86SX™ Half-Size CPU Module Vortex86SX-6121-FD-V2...
-
Page 27: Watchdog Timer
Watchdog Timer There are two watchdog timers in Vortex86SX/DX CPU. One is compatible with M6117D watchdog timer and the other is new. The M6117D compatible watchdog timer is called WDT0 and new one is called WDT1. We also provide DOS, Linux and WinCE example for your reference. For more technical support, please visit: http://www.dmp.com.tw/tech or download the PDF file:... -
Page 28: Gpio
GPIO (General Purpose Input / Output) 40 GPIO pins are provided by the Vortex86SX/DX for general usage in the system. All GPIO pins are independent and can be configured as inputs or outputs, with or without pull-up/pull-down resistors. We also offer DOS, Linux and WinCE example for your reference. For more technical support, please visit: http://www.dmp.com.tw/tech or download the PDF file:... -
Page 29: Spi Flash
SPI flash (Serial Peripheral Interface) As SPI Flash Serial Peripheral Interface) offers many benefits including: reduced controller pin count, smaller and simpler PCBs, reduced switching noise, less power consumption, and lower system cost Many of users may consider using a formatted SPI flash to boot for the system or emulate SPI flash as Floppy (A: Driver or B: Driver). -
Page 30: Chapter 3 Driver Installation
C h a p t e r Driver Installation Operating system support The Vortex86SX-6121-FD-V2 ISA CPU board supports Embedded software: Free DOS, DOS 6.22, PCDOS 7.1, DR-DOS, x-DOS, OS/2, Windows CE 5.0 / 6.0 Please get the drivers from the Driver CD which attached with the standard packing of Vortex86SX-6121-FD-V2 board or please get it from DMP official website: http://www.dmp.com.tw/tech/vortex86sx/ Vortex86SX-6121-FD-V2 also supports most of the popular Linux distributions, for more detail... -
Page 31: Appendix
Mity-Mite Serial Server, Web Camera Tiny Server and RSIP Serial Server. DSock is free for All ICOP products using M6117D/Vortex86/Vortex86SX/Vortex86DX CPU and ICOP also provide the business version of DSock for those customers who are using other x86 CPUs. -
Page 32: Bios Default Setting
BIOS Default setting If the system cannot be booted after BIOS changes are made, Please follow below procedures in order to restore the CMOS as default setting. Press “End” Key, when the power on Press <Del> to enter the AMI BIOS setup Press “F9”... -
Page 33: Warranty
Warranty This product is warranted to be in good working order for a period of one year from the date of purchase. Should this product fail to be in good working order at any time during this period, we will, at our option, replace or repair it at no additional charge except as set forth in the following terms.