User Manual NAD11-103-SD with DM&P Vortex86DX2 500MHz processor Version 1.0 ICOP Technology Inc. ...
Page 2
No part of this manual may be reproduced, copied, translated or transmitted, in whole or in part, in any form or by any means without the prior to written permission of ICOP Technology Inc. ⓒCopyright 2015 ICOP Technology Inc Trademarks Acknowledgement Vortex86DX2 is the registered trademark of DM&P Electronics Inc.
PC/104 controller. In addition, the NAD11-103-SD family of controller is designed as a plug in replacement, with backward compatibility to support legacy software to help extend existing product life cycle without heavy re-engineering.
PS/2 Mouse cable x 1 PS/2 Keyboard cable x 1 GPIO cable x 1 NAD11-103-SD USB cable x 2 (USB port x 4) LAN cable x 1 VGA cable x 1 RS232 cable x 4 Screw Kit x 1 ICOP Technology Inc.
Onboard 4MB SPI Flash Disk Support SD Card Touch controller PS/2 interface (Optional) RS232 port x3 RS-232/485 port x1 USB port (Ver. 2.0) x4 I/O Interface USB HotSWAP x1(Optional) 16-bit GPIO port x1 10/100Mbps Ethernet port x1 C port x1 ICOP Technology Inc.
Page 10
C (Optional) Free DOS, DOS 6.22, PCDOS 7.1, DR-DOS, x-DOS, OD/2, Operating Windows Embedded Compact 7, Windows Embedded Compact 6, System Support Windows XP Professional, Windows Embedded Standard(XPE), POS Ready(WePOS), Embedded Linux, X-linux, QNX, Vxworks and FreeBSD. ICOP Technology Inc.
Pin# Single Name Pin # Single Name MSCLK MSDATA J6: USB 0&1 Pin# Single Name Pin # Single Name LUSBD0- LUSBD1- LUSBD0+ LUSBD1+ GGND GGND J7: LAN Pin# Single Name Pin # Single Name ATX+ ATX- ARX+ LED0 LED0+ ARX- LED1+ LED1 ICOP Technology Inc.
NAD11-103-SD User Manual J8: VGA Pin# Single Name Pin # Single Name R OUT G OUT B OUT HSYNC_A VSYNC_A J9: Reset Pin# Single Name Pin # Single Name RST_SW ICOP Technology Inc.
J15: COM3 (RS232) (Optional: TTL) Pin# Single Name Pin # Single Name DCD3 RXD3 TXD3 DTR3 DSR3 RTS3 CTS3 J16: COM4 (RS232) (Optional: TTL) Pin# Single Name Pin # Single Name DCD4 RXD4 TXD4 DTR4 DSR4 RTS4 CTS4 ICOP Technology Inc.
NAD11-103-SD User Manual J17: GPIO PORT 0/1 Pin# Single Name Pin # Single Name GP00 GP10 GP01 GP11 GP02 GP12 GP03 GP13 GP04 GP14 GP05 GP15 GP06 GP16 GP07 GP17 ICOP Technology Inc.
J24: Power Connector Pin# Single Name Pin # Single Name J25: Buzzer Pin# Single Name Pin # Single Name Buzzer J26: USB 2&3 Pin# Single Name Pin # Single Name LUSBD2- LUSBD3- LUSBD2+ LUSBD3+ GGND GGND ICOP Technology Inc.
000E0000 – 000EFFFF USB Legacy SCSI ROM space 000F0000 – 000FFFFF Motherboard BBIOS FEFDBC00 – FEFDBCFF Standard OpenHCD USB Host Controller FEFBB400 – FEFBB4FF Onboard Ethernet Adapter FEFDB800 – FEFDBFFF Standard Enhanced PCI to USB Host Controller ICOP Technology Inc.
Page 25
DMA High page register 0490h – 0499h Instruction counter register 04D0h – 04D1h 8259 Edge / level control register 0CF8h – 0CFFh PCI configuration port DE00h – DEFFh On board LAN FC00h – FC05h SPI Flash BIOS control register ICOP Technology Inc.
Page 26
USB/ Ethernet 10/ 100M LAN IRQ10 Serial Port 3 IRQ11 Serial Port 4 IRQ12 Mouse IRQ13 Math Coprocessor IRQ14 Multimedia Device IRQ15 Hard Disk Controller #2 DMA Mapping Address Description Usage DMA0 DMA1 DMA2 DMA3 DMA4 DMA5 DMA6 DMA7 ICOP Technology Inc.
NAD11-103-SD User Manual 3 Software Resources 3.1 ICOP Technical Resource Website In the following website, you will find our latest user manuals, including OS support resources systems such as evaluation images for Windows Embedded CE 7.0, Windows Embedded CE 6.0, Windows Embedded CE 5.0, and Windows XP Embedded (Win XPe).
4 Technical support 4.1 LCD 4.1.1 Introduction The NAD11-103-SD offers two different interfaces which support maximum resolution up to 1024 x 768 (at 60MHz) connecting to LCD Flat Panel: 18-bit/24-bit TFT-LCD and 18-bit LVDS. 4.1.2 Pin Assignment of LVDS and TFT-LCD...
4.2.2 Console Redirection Access to computer board through serial port, you can work on NAD11-103-SD without VGA display or monitor. The default access port is COM1 and disabled. If you would like to use this function, please go to the path below to enable Console Redirection.
NAD11-103-SD User Manual 4.2.3 RS232/485 Switching COM2 on NAD11-103-SD is available switching from RS232 to RS485, and vice versa. You can choose the mode you need depending on your demands. The default setting for serial port is RS232. Path: Chipset >Southbridge Configuration >TXDEN Serial Port Type Configuration ...
Path: Advanced >IDE Configuration >IDE Operate Mode [Legacy] >Standard IDE Compatible [Disabled] If you would like to install Linux on ICOP’s computer boards, please change IDE Operate Mode to [Native] and enable Standard IDE Compatible. Path: Advanced >IDE Configuration >IDE Operate Mode [Native] >Standard IDE Compatible [Enabled]...
NAD11-103-SD User Manual 4.2.5 Advanced PCI/PnP Setting Two statuses for IRQ setting: IRQ3 [Reserved]: IRQ is reserved for an ISA device. IRQ5 [Available]: IRQ is free to be allocated for an I/O device. Path: PCIPnp >IRQ ICOP Technology Inc.
Returned goods should always be accompanied by a clear problem description. Should you have questions about warranty and RMA service, please contact us directly. ICOP Technology Inc. Address: No. 15 Wugong 5th Road, Xinzhuang Dist. New Taipei City, Taiwan (R.O.C.) 24890...