Download  Print this page


Basic Features
■ MPEG Noise Filter (Off / Low / Medium / High /
Auto): Reduces MPEG noise to provide improved
picture quality.
■ HDMI Black Level (Normal / Low): Selects the black
level on the screen to adjust the screen depth.
Available only in HDMI mode (RGB signals).
■ Film Mode (Off / Auto1 / Auto2): Sets the TV to
automatically sense and process film signals from all
sources and adjust the picture for optimum quality.
Available in TV, AV, COMPONENT (480i / 1080i)
and HDMI (480i / 1080i).
■ Screen Burn Protection: To reduce the possibility of
screen burn, this unit is equipped with screen burn
prevention technology. The Time setting allows you to
programme the time between movement of the picture
in minutes.
Pixel Shift (Off / On): Using this function, you can
minutely move pixels on the PDP in horizontal or vertical
direction to minimize after image on the screen.
Optimum condition for pixel shift
Time (minute)
The Pixel Shift value may differ depending on the
monitor size (inches) and mode.
This function is not available in the Screen Fit
Auto Protection Time (10 min / 20 min / 40 min /
1 hour / Off): If the screen remains idle with a still
image for a certain period of time defined by the user,
the screen saver is activated to prevent the formation of
ghost images on the screen.
Scrolling: This function removes after-images on the
screen by moving all the pixels on the PDP according
to a pattern. Use this function when there are remaining
after images or symbols on the screen, especially when
you displayed a still image on the screen for a long time.
The after-image removal function has to be
executed for a long time (approximately 1 hour)
to effectively remove after-images on the screen.
If the after-image is not removed after performing
the function, repeat the function again.
Press any key on the remote control to cancel this
Side Grey (Dark / Light): When you watch TV with the
screen ratio set to 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme
left and right sides.
1~4 min
4 min
Picture Reset (OK / Cancel)
Resets your current picture mode to its default settings.
Setting up the TV with Your PC
Set the input source to PC.
Auto Adjustment
Adjust frequency values/positions and fine tune the settings
Not available when connecting with an HDMI/DVI cable.
■ Coarse / Fine: Removes or reduces picture noise. If the
noise is not removed by Fine-tuning alone, then adjust
the frequency as best as possible (Coarse) and Fine-
tune again. After the noise has been reduced, readjust
the picture so that it is aligned to the centre of screen.
■ Position: Adjust the PC screen position with direction
button (▲ / ▼ / ◄ / ►).
■ Image Reset: Resets the image to default settings.
Using Your TV as a Computer (PC) Display
Setting Up Your PC Software (Based on Windows XP)
Depending on the version of Windows and the video card,
the actual screens on your PC may differ in which case the
same basic set-up information will almost always be applied.
(If not, contact your computer manufacturer or Samsung
1. Click on "Control Panel" on the Windows start menu.
2. Click on "Appearance and Themes" in the "Control
Panel" window and a display dialog-box will appear.
3. Click on "Display" and a display dialog box will appear.
4. Navigate to the "Settings" tab on the display dialog-box.
y The correct size setting (resolution)
[Optimum: PS42C450: 1024 X 768 / PS50C450: 1360
X 768 pixels]
y If a vertical-frequency option exists on your display
settings dialog box, the correct value is "60" or "60 Hz."
Otherwise, just click "OK" and exit the dialog box.


Table of Contents

   Also See for Samsung PS42C450B1W

   Related Manuals for Samsung PS42C450B1W

This manual is also suitable for:


Comments to this Manuals

Symbols: 0
Latest comments:
  • charedoss Mar 31, 2016 10:42:
    You can use Idealshare VideoGo to Convert MPEG to Samsung TV, MPG to Samsung TV, MPEG-1 to Samsung TV, MPEG-2 to Samsung TV supported H.264/MPEG​-4 AVC Video(*.mp​4) perfectly.
  • lrryur Dec 08, 2013 02:50:
    samsung plasma tv ps42b450b1​w how to get a download update and intalled via usb