Master Control Section; Aux Return 1 Aux Return - Yamaha MX200-12 Operation Manual

Master control section

8
–15 +15 –15 +15
HIGH HIGH
+15 +15
–15 –15
LOW LOW
0 0
10 10
AUX 1 AUX 2
0 0
10 10
LEVEL LEVEL

AUX RETURN 1 AUX RETURN 2

7
10 10
5 5
0 0
5 5
10 10
15 15
20 20
30 30
00 00
6
AFL AFL
AUX SEND 1 AUX SEND 2
3
ON
1
4
10 10
5 5
0 0
5 5
10 10
15 15
20 20
30 30
40 40
00 00
L ST R
2
4
MIXING CONSOLE
+6 +6
+4 +4
+2 +2
0 0
–2 –2
–4 –4
–7 –7
–10 –10
–15 –15
–20 –20
–00 –00
L ST R
MONO PFL/AFL
1 AUX 2 3 AUX 4
METER SELECT
PHANTOM
10 10
PFL
5 5
0 0
5 5
10 10
10
15 15 0
REC OUT
20 20
30 30
00 00
0
10
TAPE IN
AFL AFL
AUX SEND 3 AUX SEND 4
ON
0 10
AFL
PHONES
10
5
0
5
10
15
20
30
40
00
MONO PHONES
5
1 STEREO ON switch
This switch turns the ST OUT output on/off.
When this switch is off, levels will not be displayed in the
ST meters. The MONO OUT signal will be sent regardless
of this switch.
2 STEREO L, R master faders
These faders adjust the final level of the combined signals
from all channels, and send them from the STEREO OUT
connectors.
The ST meters allow you to monitor the L and R outputs.
3 MONO ON switch
This switch turns the MONO OUT on/off.
4 MONO AFL switch
When this switch is on, the signal being output to MONO
OUT can be monitored in the headphones.
C
5 MONO fader
D
This fader adjusts the output level of the MONO OUT con-
E
nector.
6 AUX SEND 1–4 AFL switches
9
When you wish to monitor the output signals being sent to
AUX SEND 1–4, press the appropriate switch.
0
The level of the AUX SEND whose switch is on will be in-
dicated by the PFL/AFL meter.
7 AUX SEND faders
A
These faders adjust the level of the output signals sent from
AUX SEND 1–4.
The 8 METER SELECT switch can be set so that these
AUX SEND signals are monitored in the level meters.
8 AUX RETURN 1, 2 controls
<LEVEL>
The LEVEL knobs control the level at which signals from
effect units etc. connected to the L/MONO, R jacks of
B
AUX RETURN 1, 2 are sent to the L, R bus.
If a plug is inserted into only the L/MONO jack, the same
signal will be sent to both L and R buses.
<AUX1 (AUX2)>
The AUX1 knobs control the level at which signals from
effect units etc. connected to the L/MONO, R jacks of
AUX RETURN 1, 2 are sent to the AUX SEND 1 (2) fader.
After being adjusted at the fader, the signal is output from
the rear panel AUX SEND 1 (2).
<LOW>
This knob is a low frequency equalizer that provides 80Hz
shelving equalization of the signal input at AUX
RETURN.