Yamaha MCX-P200 Getting Started

MCX-RC100 / MCX-A300 / MCX-P200
GETTING STARTED
This guide explains the basic way to build a WiFi network between
your MusicCAST2 products and WiFi router and enjoy digital music
distribution via the WiFi network.
Complete description of MusicCAST2 products is available on our
website. To access the MusicCAST2 website, please enter the following
URL on your browser.
MusicCAST2 website:
www.yamaha.com/musiccast
Network to build in this guide
MCX-RC100
(Music Commander)
ZONE
MUSIC/ REMOTE
VOLUME BACK HOME
MUTE
NETWORK MUSIC COMMANDER MCX-RC100
(Net Radio, etc)
MCX-A300
(Music Player with amplifier)
WIRELESS LAN
MCX-P200 WiFi router
(Music Player without amplifier)
PURE DIRECT
VOLUME
AUDIO SELECT/ TONE SEARCH STEREO/
INPUT REC OUT MENU CONTROL ENTER PRESET/TUNING/CH MEMORY MODE MONO BAND CATEGORY INFO
WIRELESS LAN MAIN ZONE STRAIGHT EFFECT MULTI ZONE ZONE 2 ZONE ON/OFF ZONE 3 ZONE CONTROLS
YPAO SILENT CINEMA S VIDEO VIDEO L AUDIO R OPTICAL
PROGRAM OPTIMIZER MIC PHONES VIDEO AUX USB
MASTER
Network receiver
(RX-V3900, etc)
PURE DIRECT
VOLUME
AUDIO CONTROL SELECT TONE ENTER PRESET/TUNING/CH MEMORY SEARCH MODE MONO STEREO/ CATEGORY INFO
MAIN ZONE INPUT STRAIGHT MULTI ZONE ZONE ON/OFF BAND ZONE CONTROLS
ON/OFF YPAO EFFECT SILENT CINEMA S VIDEO VIDEO ZONE 2 L AUDIO ZONE 3 R OPTICAL
PROGRAM OPTIMIZER MIC PHONES VIDEO AUX
OFF ON MASTER
Receiver
(RX-V1900, etc)
Wired
WiFi
Wired or WiFi
&
• This guide assumes that you have an Internet connection and
your WiFi router is being connected to the Internet.
• This guide is printed prior to production. Design and specifications
are subject to change in part as a result of improvements, etc.
1
Preparation
Charging the Music Commander (MCX-RC100)
First, charge the Music Commander (MCX-RC100) as shown below. It
takes about 135 minutes to fully charge the built-in battery.
�
AC adapter
y
The Music Commander automatically turns on by charge. If not,
press and hold the control pad for more than two seconds to turn on it.
How to use the Music Commander's control
pad
• To move the selection from • To move the page up and down
side to side or up and down
©2009 Yamaha Corporation All rights reserved. Printed in China
U
• To enter the highlighted menu or confirm the selection
y
Press the control pad until you hear click sound. It does not react to
a touch.
2

Cable connections

For MCX-A300
1 Connect front right and left speakers to the SPEAKERS (L/R)
terminals using speaker cables.
2 If desired, connect a subwoofer to the SUBWOOFER OUT jack
using a subwoofer (pin-jack) cable.
WAN 3 Plug the supplied AC adapter into the adapter connector, connect
the power cable to the AC adapter, and then plug into an AC wall
outlet.
MCX-A300
WPS
USB
SUBWOOFER OUT SPEAKERS
2 1 1
Subwoofer Right Left
Front speakers
For MCX-P200
1
Plug an analog audio cable into the AUDIO (L/R) jacks.
2
Plug the other end of the analog audio cable into analog input jacks
available on your receiver (RX-V1900, etc).
3
If desired, connect a subwoofer to the SUBWOOFER jack using a
subwoofer (pin-jack) cable.
4
Plug the supplied AC adapter into the adapter connector, connect
the power cable to the AC adapter, and then plug into an AC wall
outlet.
MCX-P200
WPS USB REMOTE CONTROL OUT
PRE OUT
AUDIO SUBWOOFER
1 3
L R
Subwoofer
BD/HD DVD DVD CBL/SAT IN DVR IN VCR
L
IN MD/
(PLAY) CD-R
R
2
CD TV
WR96010-1
y
• By using the supplied IR flasher, you can control the receiver
connected to the MCX-P200 with the Music Commander. For
details, refer to the online manual at the MusicCAST2 website.
• For information on other connections for your receiver, refer to the
manual supplied with it.
For a network receiver (RX-V3900, etc)
1 Connect your network receiver to a LAN port of the WiFi router
using a network cable (CAT-5 or higher straight cable).
2 Plug the supplied power cable into the AC inlet and then plug into
an AC wall outlet.
WAN
LAN
WiFi router
1
OFF ON
POWER
DC IN 19V
( LAN )
DOCK NETWORK y
For information on other connections for your network receiver,
refer to the manual supplied with it.
3
3
WiFi settings
AC adapter
y
If your WiFi router supports WPS, you can simply establish a
wireless connection between this WiFi router and the MusicCAST2
system using WPS. To activate the Music Players, press and hold
the WPS setup button more than one second. For complete details,
refer to the online manual at the MusicCAST2 website and WiFi
router manual.
1.
Make sure that your WiFi router is turned on.
2.
Music Commander:
ZONE
MUSIC/
REMOTE
VOLUME
MUTE
OFF ON
POWER
DC IN 19V
( LAN )
ZONE
DOCK NETWORK
MUSIC/
REMOTE
4
VOLUME
AC adapter MUTE
Receiver (RX-V1900, etc)
ZONE
MUSIC/
REMOTE
VOLUME
MUTE
3.
To WAN
Network receiver (RX-V3900, etc)
NETWORK
2
AC IN
Power cable
4.
ZONE
Setup
→
BACK HOME
NETWORK MUSIC COMMANDER MCX-RC100
ê
BACK HOME
NETWORK MUSIC COMMANDER MCX-RC100
ê
BACK HOME
NETWORK MUSIC COMMANDER MCX-RC100
[Network] – [Setup] – [Wireless LAN] – [Easy Setup]
Control
pad
[Network]
Use the control pad to select and enter the "Network" menu
[Setup] – [Wireless LAN]
as shown below. In the same way, select
– [Easy Setup].
ZONE
MUSIC/
REMOTE
BACK HOME
VOLUME
MUTE
NETWORK MUSIC COMMANDER MCX-RC100
ê
ZONE
MUSIC/
REMOTE
BACK HOME
VOLUME
MUTE
NETWORK MUSIC COMMANDER MCX-RC100
ê
ZONE
MUSIC/
REMOTE
BACK HOME
VOLUME
MUTE
NETWORK MUSIC COMMANDER MCX-RC100
Control Select a WiFi router to use for the WiFi
pad
connection.
ZONE
MUSIC/
REMOTE
BACK HOME
VOLUME
MUTE
NETWORK MUSIC COMMANDER MCX-RC100
ê
ZONE
MUSIC/
REMOTE
BACK HOME
VOLUME
MUTE
NETWORK MUSIC COMMANDER MCX-RC100
(continued on the back side)